nstallation and ssembly- ncore Projector Mount Protected by U.S. Patent No. 6,042,068 Model: PRL4 MPORTNT! Read entire instruction sheet before you start installation and assembly. WRNN! nstaller must verify that the will safely support the combined weight of the ase Unit, Projector dapter Plate, and video projector. This product contains all mounting hardware for direct attachment to a wood joist. oncrete anchors (accessory kit 200, see page 2) sold separately. This product is to be used in combination with one of several Projector dapter Plates (PP models). To order Projector dapter Plates, xtension olumns, or additional mounting hardware call customer service at -800-729-0307 or 708-865-8870. efore you start check the parts list below to make sure all of the parts shown are included. Peerless ndustries, nc., 980 awthorne venue, Melrose Park, L 6060 www.peerlessindustries.com D Parts List Description projector mount plate washer head wood screw #4 x 2.5 (6mm x 65mm) M6 x x 20mm socket head screw w/ flat and lock washer security allen wrench M5 x.8 x 8mm socket pin screw main bracket assembly fiber washer retaining collar M5 x.8 x 0mm socket pin screw roll adapter bracket interface bracket Qty. 2 9 2 3 Part Number 054-003 5S-05-03 520-029 560-9646 520-062 054-044 540-9432 800-375 520-64 054-050 055-25 * R This product is intended for use with UL Listed products and must be installed by a qualified professional installer. Note: ctual parts may appear slightly different than illustrated. our.406 dia. holes provided for threaded rod * installations. Materials and procedure for such installations are the sole responsibility of the installer. D 2003 Peerless ndustries, nc. ll rights reserved. Peerless is a registered trademark of Peerless ndustries, nc. ncore is a trademark of Peerless ndustries, nc. ll other brand and product names are trademarks or registered trademarks of their respective owners. of 5 Parts,, and are used only for installations that incorporate an extension column. SSUD: 09-09-02 ST #: 054-922-3 --03 Visit the Peerless Web Site at www.peerlessindustries.com or customer service call -800-729-0307 or 708-865-8870.
wood joist 5/32"(4mm) 5/6"(8mm) oncrete nchor ttachment to a Wood oist. Use a stud finder to locate joist. Drill two 5/32" (4mm) dia. holes 2.5" (65mm) deep into joist center. ttach projector mount plate () using #4 x 2.5" (6mm x 65mm) wood screws (). UTON: Tighten wood screws so plate is firmly attached. ut DO NOT TTN WT XS- SV OR! Overtightening can cause stress damage to wood screws, greatly reducing their holding power! Tighten to 80 in. lbs. (9 N.M.) maximum torque. SUR TO DRLL NTO OST NTR! Skip to Step 4 ttachment to a oncrete eiling. NOT: oncrete anchors are sold separately. Order accessory kit #200. Drill two 5/6" (8mm) dia. holes.75" (45mm) deep. ttach projector mount plate () using two concrete anchors. Tighten to 80 in. lbs. (9 N.M.) maximum torque. See also ONRT NOR NSTLLTON below. Skip to Step 4 US ONLY RWL TM #5005 OR LT TM L84 ONRT XPNSON NORS [.32 x.625 (8mm x 4mm)]. Order accessory kit #200. ROSS STON concrete concrete anchor Tighten to 80 in. lbs. (9 N.M.) maximum torque. TS ONRT NORS R OR DRT TTMNT TO LOD RN ONRT ONLY! NOT OR TTMNT TO ONRT LN OVRD WT PLSTR, DRYWLL, TL OR OTR NSN MTRL! ONRT NOR NSTLLTON 2 of 5 SSUD: 09-09-02 ST #: 054-922-3 --03 Visit the Peerless Web Site at www.peerlessindustries.com or customer service call -800-729-0307 or 708-865-8870.
xtension column applications only: nsert end of extension column into threaded fitting in plate. Tighten securely - four or five complete turns. lign slot in extension column with one of the small holes in the side of the threaded fitting. nsert and tighten one M5 x.8 x 0mm socket pin screw ( ) into hole to lock extension column to threaded fitting. Tighten screw allen wrench (D). WRNN: or safety, extension column must be locked to threaded fitting with screw ( )! ttach projector mount plate () with fiber washer () and retaining collar (). Tighten retaining collar securely, four or five complete turns, aligning one hole in the side of retaining collar with slot in the end of extension column. rom inside insert and tighten one M5 x.8 x 0mm socket pin screw ( ) into hole in retaining collar. Tighten screw with allen wrench (D). slot threaded fitting plate (sold separately) extension column (sold separately) Note: You may need to thread the socket pin screw from the outside first (approximately 3 turns) to loosen any buildup that may be on the threads. WRNN: or safety, retaining collar must be locked to extension column with screw ( )! ttach roll adaptor bracket () to plate () using four M6 x x 20mm socket head security screws (). Tighten using 4mm allen wrench provided. Next attach main bracket () using remaining fasteners (). Tighten using 4mm allen wrench provided. MPORTNT: Do not lose or dispose of allen wrench. t will be required to attach the Projector dapter Plate. NOT: rrow indicates front of main bracket (). 3 of 5 SSUD: 09-09-02 ST #: 054-922-3 --03 Visit the Peerless Web Site at www.peerlessindustries.com or customer service call -800-729-0307 or 708-865-8870.
Note: ttach adapter plate to projector (see PP instructions) prior to proceeding to step 5 Note: The Projector dapter Plate and projector you are installing may differ in appearance from the sample illustrated below. Place interface bracket () on top of adapter plate as shown. NOT: # Notch on interface bracket indicates front of projector. *Notch on adapter bracket indicates front of projector. Rotate interface bracket until the two holes line up with two holes on adapter plate. Make sure that both front of interface bracket () and projector adapter plate are closely aligned. # * asten interface bracket () to adapter plate using two M5 socket-pin screws (). Tighten screws () using 4mm allen wrench (). 4 of 5 SSUD: 09-09-02 ST #: 054-922-3 --03 Visit the Peerless Web Site at www.peerlessindustries.com or customer service call -800-729-0307 or 708-865-8870.
Position four tabs in interface bracket () behind four tabs in base unit. Slide forward to engage latch. SUR TT LT S ND! WRNN: Do not lift more weight than you can handle! Use additional man power or mechanical lifting equipment to safely handle placement of the video projector! SURTY OPTON Lock the latch by tightening M6 x x 20mm socket head security screw () through hole in base unit, into threaded hole in latch. Tighten using 4mm allen wrench. MPORTNT: llen wrench is your key for projector removal. Store it in a safe place. (cutaway) (cutaway) latch latch inal lignment To adjust Yaw (swivel) for flush mounting applications: Loosen wood screws until projector mount can be rotated. Rotate mount to desired position and retighten screws. To adjust Yaw (swivel) for extension column applications: Rotate mount to desired position. nsert and tighten one remaining socket pin screw ( ) into tab in projector mount plate () as shown below. To adjust pitch (forward and backward tilt), loosen the two screws on each side of the main bracket assembly (). Tilt mount to desired position and tighten screws. To adjust roll (side to side tilt), loosen the two screws on each side of the roll adapter bracket (). Tilt mount to desired position and tighten screws. Peerless offers several Projector Mounts to fit various video projectors. New Projector Mounts are continually being developed to meet the demands of a growing projector market. To find out if a mount is available for your particular projector call Peerless customer service at -800-729-0307 or 708-865-8870. 5 of 5 SSUD: 09-09-02 ST #: 054-922-3 --03 Visit the Peerless Web Site at www.peerlessindustries.com or customer service call -800-729-0307 or 708-865-8870.