Fitment Instructions
1. Fitment Tools, Fasteners & Materials The tables below show the equipment, i.e. tools, fasteners, hardware and consumables required to start and finish the prep table fitment. 1.1. Tools Required: TOOL PURPOSE Drill Drill mounting holes into prep table frame and vehicle 4.8mm Drill Bit Drill mounting holes into prep table and vehicle Rivet Gun Fix rivets to mounting parts Crimping tool Crimps wires together 1.2. Fasteners required: (Included with canopy) ITEM QUANTITY 4.8X15AS Blind Rivets 4 off 4.8X10AS Black Rivets 5 off Wire crimps 4 off 1.3. Hardware Required: (Included with canopy) ITEM PURPOSE Frame 1 off Sliding Extrusion 1 off 1 off 2
1.4. Consumables Required: ITEM PURPOSE Turpentine Cleaning purposes Cloth Cleaning purposes Black silicone or Sikaflex Apply to the sliding extrusion when fixing it onto the vehicle Figure 1: Sliding Extrusion Figure 2: Frame Figure 3: 3
2. Setting up the onto the Vehicle The prep table slides into the rope mould that should be mounted onto the vehicle. 2.1. Mounting the Rope Mould to the Vehicle a) Step 1 Drilling the mounting holes into the Rope Mould Use a drill and a 4.8mm drill bit to drill 3 holes evenly spaced along the length of the rope mould as shown in Figure 4 below. Mounting Holes Sliding Extrusion Figure 4: Drilling Mounting Holes into rope mould b) Step 2 Drilling the mounting holes into the vehicle Place the rope mould in the mounting position and use as a guide to drill mounting holes into the vehicle as shown in Figure 5 below. Use the 4.8mm drill bit. Drill Vehicle Rope Mould Figure 5: Drilling Mounting Holes into vehicle 4
c) Step 3 Apply Sikaflex to the mounting surface Sikaflex Mounting Surface Figure 6: Applying Silcone/Sikaflex to the Surface d) Step 4 Riveting the rope mould to the mounting surface Place the sliding extrusion in the mounting position, insert rivets and rivet it to the surface using a rivet gun and 4.8x10AS rivets. 4.8x10AS Rivets Rivet gun Rope Mould Figure 7: Riveting rope mould to surface 5
2.2. Sliding prep table into sliding extrusion Once the sliding extrusion is fixed, the prep table slides into it as shown in Figure 8 and Figure 9. Sliding Extrusions Figure 8: Sliding into Rope Mould Sliding Extrusions Top Section Bottom Section Figure 9: in setup position 6
2.3. Installing prep table wire supports a) Step 1 Slide wire into 1 side of the crimper Crimper Wire Figure 10: Inserting wire into 1 side of crimper b) Step 2 - Fold the wire and insert into the other side of the crimper Crimper Wire Fold Figure 11: Inserting the wire into other side of crimper 7
c) Step 3 - Scrimp wires together using a crimping tool Before crimping the wires together, fit the wire fold over the 4.8x15 flange rivet and adjust the crimper to have a close fit on the rivet. Top Wire Support 4.8x15 Flange Rivet Top Section Figure 12: Adjusting Crimper for a close fit Crimping Tool Wire Fold Figure 13: Crimping wires together 8
d) Step 4 Rivet wire supports to the prep table top section Insert 4.8x15 flange rivet into wire fold, then insert into pre-drilled holes located in the top section of the prep table as shown in Figure 11 above and rivet the wire support to the prep table. 4.8x15 Flange Rivet Top Wire Support Top Section Figure 14: Rivet Top Wire Support e) Step 5 Adjusting and crimping wire supports to prep table bottom section Adjust the length of the wire support before crimping it to keep the prep table bottom section 90 degrees to the top section when table unfolds. Insert 4.8x15 flange rivet into mounting hole. Bottom Section Bottom Wire Support Top Section Bottom Section Mounting holes Wire Support Figure 15: Adjusted Wire Support 9
f) Step 6 - Use wire crimping method in step 3 for the other end of the wire support. Wire Support Crimping Tool Figure 16: Crimping other end of wire support g) Step 7 Rivet wire support to bottom section Bottom Section Rivet Gun Figure 17: Rivet bottom wire support 10
Figure 18: setup complete 3. Installing prep table frame for table storage a) Step 1 Measure mounting holes into frame Measure hole positions on the frame as shown in Figure 18. This must be done for each corner of the frame. 20mm Frame Width Mounting Hole 40mm Frame Length Figure 19: Measuring mounting holes on the frame 11
b) Step 2 Drill the mounting holes through the frame Drill Frame Figure 20: Drilling mounting holes on the frame c) Step 3 Mark off holes on the vehicle mounting surface Place the frame in the mounting position and mark off corresponding holes onto the vehicle surface Vehicle Mounting Surface Mounting holes Frame Figure 21: Marking off mounting holes 12
d) Step 4 Drilling mounting holes into vehicle surface Drill the mark off points using a drill and 4.8mm drill bit. Inside Surface of side door Hand Drill and 4.8mm Drill bit Figure 22: Drill mounting holes into canopy side door e) Step 4 Rivet the frame onto the canopy side door Place the frame in position on the inside of the side door and align the holes. Insert rivets from the outside surface of the side door into the frame mounting holes and rivet it down. Rivet Gun Outside Surface of side door Figure 23: Rivet frame from the outside surface 13
Frame Inside Surface of Side Door Rope for holding table 4.8x10AS Rivets Figure 24: Frame installed 4. Locking into Frame a) Step 1 Fold table close and Insert into the frame Prep table frame Figure 25: Inserting Table into frame 14
b) Step 2 Lock table into frame Use the rope at the bottom of the frame to fix the table in place. Swing the rope over the table and hook it onto the top of the frame. Prep table frame Locking Rope Figure 26: Fixing table in place Figure 27: Storage complete 15