Installation and ssembly: Flat-Panel Base Lock-own Kit for Samsung isplay Models Models: HLG452-SM, HLG452-SM-Q10 Maximum isplay Size: 100 lb (45.35 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or (708) 865-8870 Fax: (708) 865-2941 www.peerlessmounts.com
Note: Read instruction sheet before you start installation and assembly. Parts may appear slightly different than illustrated. Parts List HLG452-SM HLG452-SM-Q10 escription qty part # qty part # lock-down plate 1 090-1757 10 090-1757 B adhesive strip 4 570-0017 40 570-0017 1/4-20 x 1 3/4" carrage bolt 2 520-1017 20 520-1017 1/4-20 sloped nut 3 530-0035 23 530-0035 e plastic cap 2 590-1294 20 590-1294 F rubber pad - 3/16 x 1" x 3/4" 6 590-1159 60 590-1159 G # 10 x 3/8 phillips pan TEk screw 4 520-2612 40 520-2612 H M4 x 16 phillips pan trilobe screw 2 520-2621 20 520-2621 I M4 x 16 security screw 2 520-1087 20 520-1087 J 4mm security allen wrench 1 560-9646 3 560-9646 B E F G H I J Tools Needed for ssembly drill 1/4" drill bit 5/8" open box wrench phillips screwdriver 3M Rubber & Vinyl 80 Spray dhesive (generic name: ontact 80 Neoprene Vinyl Spray dhesive) This product can be found at hardware and craft stores, as well as on the 3M website: http://solutions.3m.com/. ccessory 939-1/4-20 x 2 1/4" replacement carriage bolts (ontact ustomer Service) 943 - Installation Template (plate only) Installation Option 1 (Fasteners) Pages 3 and 4 Installation Option 2 (dhesive Strips) Pages 5 and 6 Installation of Security Screws for Base/Screen ssembly Page 7 2 of 7
Installation Option 1 (Fasteners) ISPLY MOEL HOLE PTTERNS SMSUNG LN-T2353HTX LN-T2653HTX LN224501HX2 LN264501HX2 LN-T3253HTX LN-T4053HTX LN324501HXZ LN374501HXZ LN404501HXZ LN326501HXZ LN406501HXZ LN466501HXZ LN526501HXZ LN32B4506HXZ LN32B4576HXZ LN37B4576HXZ LN40B4576HXZ (4) # 10 x 3/8 phillips pan screws (self drillers) (G) (4) # 10 x 3/8 phillips pan screws (self drillers) (G) Note: Mounting hole bumpout must be placed on bottom flush with raised section on base. 1 Use lock-down plate () as a template to mark location of holes, point 1 and point 2, approximately 7" apart on table. rill two holes using a 1/4'' drill bit. 2 Slide two 1/4-20 x 1 3/4" bolts () through slots as shown below. NOTE: 2 1/4" carriage bolts (939) are available for use with thicker mounting surfaces. 7" POINT 1 (178 mm) POINT 2 TBLE TOP Skip to page five for Installation Option 2 (dhesive Strips) 3 of 7
3 ttach lock-down plate to display base bottom using screws provided. Refer to page three for lock-down plate/ display base stand hole pattern. NOTE: Remove existing rubber feet from display base that interfere with the lock-down plate. Larger display bases may require additional rubber pads (F) to provide additional support at the perimeter of the base. ISPLY BSE STN RUBBER FEET SREWS PROVIE NOTE: isplay base stand and mounting hole locations may appear different than illustrated. Mounting Lock down Slope Nuts 4 Hand tighten slope nuts () onto two of the 1/4-20 x 1 3/4" screw bolt () until snug against bottom of table as shown in etail 1. Thread another slope nut () upside-down, about two turns from first slope nut () as shown in etail 2. Insert a 5/8" open box wrench between both slope nuts () and tighten as shown in detail 3. fter slope nut is secure remove bottom slope nut and add plastic cap (E) as shown in figure 4.1. Repeat with remaining 1/4-20 x 1 3/4" screw bolt (). etail 1 BOTTOM OF ESK etail 3 NOTE: void jamming both slope nuts (G) together, doing so may make it difficult to remove slope nut used for tightening. fter slope nut is secure remove bottom slope nut. etail 2 LEVE SPE IN BETWEEN SLOPE NUTS BOTTOM OF ESK TIGHTENING SLOPE NUT (F) E TIGHTENING SLOPE NUT () 5/8" OPEN BOX WRENH FIG 4.1 4 of 7
Installation Option 2 (dhesive Strips) ISPLY MOEL HOLE PTTERNS SMSUNG LN-T2353HTX LN-T2653HTX LN224501HX2 LN264501HX2 LN-T3253HTX LN-T4053HTX LN324501HXZ LN374501HXZ LN404501HXZ LN326501HXZ LN406501HXZ LN466501HXZ LN526501HXZ LN32B4506HXZ LN32B4576HXZ LN37B4576HXZ LN40B4576HXZ (4) # 10 x 3/8 phillips pan screws (self drillers) (G) (4) # 10 x 3/8 phillips pan screws (self drillers) (G) Note: Mounting hole bumpout must be placed on bottom flush with raised section on base. 1 ttach lock-down plate to display base bottom using screws provided. Refer to page five for lock-down plate/display base stand hole pattern. NOTE: Remove existing rubber feet from display base that interfere with the lock-down plate. Larger display bases may require additional rubber pads (F) to provide additional support at the perimeter of the base. ISPLY BSE STN RUBBER FEET SREWS PROVIE NOTE: isplay base stand and mounting hole locations may appear different than illustrated. 5 of 7
2 lean bottom of lock-down plate () with rubbing alcohol. Spray bottom of lock-down plate () only where tape will be applied, with 3M rubber and vinyl #80 spray adhesive (not supplied). Pull apart the four adhesive strips (B) and remove red backing from one side. Wait at least 4 minutes for adhesive spray to dry before applying adhesive strip (B). ttach adhesive strips (B) firmly to bottom of lock-down plate () as shown below. lean with rubbing alcohol ried 3M rubber and vinyl #80 spray adhesive B 3 lean desk surface with rubbing alcohol. Use 3M rubber and vinyl #80 spray adhesive (not supplied) on the mounting surface area only. NOTE: Spray adhesive will not remove easily. Wait at least 4 minutes to dry before removing tape backing from lock-down plate () and placing firmly on surface. NOTE: There is a recommended 72 hour cure time for tape on lock-down plate (). Note: Once tape backing is removed be careful not to touch the sticky surface of the tape with fingers, as this can cause the tape to lose some of its holding power. NOTE: fter application of tape on lock-down plate (), the bond strength will increase as the adhesive flows onto the surface. t room temperature, approximately 50% of the ultimate strength will be achieved after 20 minutes, 90% after 24 hours, and 100% after 72 hours. In some cases, bond strength can be achieved more quickly by exposure to elevated temperatures (e.g. 150 F [66 ] for 1 hour). ISPLY BSE STN ried 3M rubber and vinyl #80 spray adhesive (not supplied) NOTE: isplay base stand may appear different than illustrated. desk surface 6 of 7
Installation of Security Screws for Base/Screen ssembly 4 Thread two M4 x 16 phillips pan trilobe screws (H) to top display attachment holes as shown in fig. 4.1. Remove the two M4 x 16 phillips pan trilobe screws (H) and attach display screen to display base using two M4 x 16 mm socket pin screws (I), as shown in figure 4.2. Tighten with 4 mm security allen wrench (J). Use TV supplied screws for remaining holes. NOTE: Screws are installed at a diagonal. isplay screen isplay screen H I fig 4.1 isplay base fig 4.2 NOTE: isplay and base may appear different than illustrated 7 of 7 2009, Peerless Industries, Inc. ll rights reserved. ll other brand and product names are trademarks or registered trademarks of their respective owners.