Emergency stops and safety stops

Emergency stops and safety stops www.jokabsafety.com

Contents Page Why do you need an Emergency stop? : Emergency stop for enclosure installation INC : Emergency stop for enclosure installation INC Tina : Emergency stop with LED Smile : Emergency stop with LED Smile Tina :0 Emergency stop with LED Smile S-i : Emergency stop Grab Wire Safety Switch Stop-Line : Safety stop Inca and Smile :0 Reset button Smile R : 7 8 9 0 While every effort has been taken to ensure the accuracy of information contained in this book or any associated promotional and information material BB Jokab Safety cannot accept responsibility for errors or omissions and reserves the right to make any improvements without notice. It is the users responsibility to ensure that this equipment is correctly designed, specified, installed, cared for and operated to meet all applicable local, national and international codes/regulations. Technical data in our book is correct to the level of accuracy of BB Jokab Safety s test procedures as verified by various international approved bodies. Other information (such as application examples, wiring diagrams, operation or use) is intended solely to illustrate the various uses of our products. BB Jokab Safety does not guarantee or imply that the product when used in accordance with such examples in a particular environment will fulfil any particular safety requirement and does not assume any responsibility or liability for actual use of the product based on the examples given. 0. www.jokabsafety.com :

Why do you need an Emergency stop? So that anyone shall be able to stop a machine during a machine break-down or if someone is in danger. How do I recognise an E-stop? E-stop buttons shall according to relevant standards be red with a yellow background. n emergency stop grab wire shall be red for high visibility. sign that indicates the location of the E-stop shall be green with a white picture and possibly with text in the local country's language. How shall an E-stop stop the machine? n E-stop shall stop the machine as quickly as possible. To obtain a quick stop one either removes the power directly or one lets a frequency converter 'run down' and afterwards after a little delay, remove the power. n E-stop shall not create other hazards. Therefore a risk analysis must be made for the E-stop to be correctly connected. From 00//EC, clause...... This device must: - have clearly identifiable, clearly visible and quickly accessible control devices, - stop the hazardous process as quickly as possible, without creating additional risks, - where necessary, trigger or permit the triggering of certain safeguard movements.... Requirements for E-stops are stated in the following standards and regulations 00//EC The Machinery Directive Clause... in nnex gives requirements for the emergency stop function for new machines). See also clause.. Control devices. (see chapter Standard and Regulations ) Council Directive 89//EEC (with amendments) concerning the minimum safety and health requirements for the use of work equipment by workers at work Clause. gives the requirements for the emergency stop function for older machines. See also clause.. (see chapter Standard and Regulations ) EN ISO 80 Safety of machinery Emergency stop Principles for design harmonized standard that gives technical specifications for the requirements in the Machinery Directive. Could also be used for older machinery. EN 00- Safety of Machinery - Electrical equipment of machines Part : General requirements. Harmonized standard that gives requirements for the electrical equipment of machinery including the emergency stop actuator/function. Se clauses 9.. and 9... : www.jokabsafety.com

Emergency stop for enclosure installation INC pproval: pplication: CE RTI FIED BY Emergency push button for installation in cabinets dvantages: Terminal blocks Emergency push button up to cat. /PL e acc. to EN ISO 89- Only mm's construction depth With LED info in print Push button IP, connector IP0 vailable as safety stop (black push button) 7 INC is an emergency stop designed for installation in. mm holes on cabinets. INC has potential free contacts for connection to safety relays. The connection is made in cabinets via a removable terminal which also have excellent measuring points. Inca is also available with a black pushbutton and used as a safety stop. See section on safety stops. In the emergency stop button there is a LED that displays current status on: Green = everything ok Red = this emergency push button has been pressed Off = a unit earlier in the circuit is affected 8 9 +V IQ 0 pulse I RT (+) S S () S S S INC Yellow front ring and emergency stop signs for emergency stop. 0 www.jokabsafety.com :

Emergency stop for enclosure installation INC Tina pproval: CE RTI FIED BY pplication: Emergency push button for installation in cabinets dvantages: Terminal blocks Emergency push button up to cat. /PL e acc. to EN ISO 89- Only mm's construction depth With LED info in push button Info output (Inca Tina) Push button IP, connector IP0 vailable as safety stop (black push button) INC Tina is an emergency stop designed for installation in. mm holes in equipment cabinets. In addition to the INC version, "INC Tina" is also available with electronic adjustment of the dynamic safety loop for connection to the Vital and units. The connection is made in equipment cabinets via a removable terminal block which also has marked measuring points. Inca Tina is also available with black push button and is used in this case as a safety stop. See section on safety stops. The emergency stop button has a LED that displays the current status: Green = everything is OK Red = this emergency stop has been pressed. Flashing red/green = a protection device earlier in the loop has been actuated. Vital INC Tina +V IQ 0 pulse B T B R Yellow front ring and emergency stop signs for emergency stop. Info PLC : www.jokabsafety.com

Technical data - INC /INC Tina Manufacturer: rticle no./ordering data: INC INC Tina Impact resistance (half sinusoidal) Vibration resistance (sinusoidal) Climate resistance Damp heat, cyclical Damp heat, sustained Dry heat Cooling Salt mist Level of safety: Cat. /PL e Category SIL SIL PFH d : INC INC Tina: Colour: Weight: Size: Material: Temperature: Enclosure classification Installation: BB B/Jokab Safety, Sweden TLJ000R000 TLJ000R0000 Max. 0m/s², pulse width ms, -axis, acc. to EN IEC 008--7 Max. 0 m/s² at 0 Hz 00 Hz, 0 cycles, axis, acc. to EN IEC 008-- 9 hours, + C / 97%, + C / 9 % relative humidity, as per EN IEC 008--0 days, +0 C / 9 % relative humidity, as per EN IEC 008--78 9 hours, +70 C, as per EN IEC 008-- 9 hours, -0 C, as per EN IEC 008-- 9 hours, + C in a chemical solution with NaCl as per EN IEC 008-- EN ISO 89- EN 9- EN 0 IEC/EN 08-...7 PFH d :,0 0-0 PFH d :. 0-9 Yellow, red and black pprox. grams See drawing Polyamide P, Macromelt, Polybutylenterephthalate PBT UL 9 V0-0 C to + C (operation), -0 C to +70 C (storage) Print: IP, Connector: IP0, mm Emergency stop LEDs: INC : Green: Safety device OK. Not lit: unit earlier in the circuit is affected. Red: This emergency stop has been pressed. INC Tina: Green: Safety device OK, safety circuit OK Flashing: Safety device OK, safety circuit previously broken. Red: This button is pressed in, and the safety circuit is broken. Operating voltage (LED): Current consumption (LED): Emergency stop button Operating force: Operating movement: Contact material: INC : VDC INC Tina: VDC +% -% INC : m INC Tina: 7 m ± N pprox. mm to locked position Gold-plated silver alloy Minimum current: INC : 0 m, 0 VDC/0 VC INC Tina: Maximum current: INC : VDC, VC INC Tina: Mechanical life: > 0 000 operations Standards: EN 00, EN 097-- & - EN ISO 80 ccessories: Front ring yellow for INC Emergency stop sign S D F,,mm Emergency stop sign E FT,,mm Conformity: TLJ000R000 TLJ000R000 TLJ000R000 00//EG EN 9-, EN ISO 89-, EN 0, EN 00-, EN 9-, IEC 0-, EN 000--, EN 000--, EN 097--, EN 088 7 8 9 0 www.jokabsafety.com :

Emergency stop with indication Smile pprovals; CE RTI FIED BY pplication: To stop a machine or a process Features: Emergency push button up to cat. /PL e acc. to EN ISO 89- With LED info in push button Robust Push button IP, housing IP7 vailable as safety stop (black push button) Smile - small and cost effective E-stop In order to fulfil the need for a small and easy to install E-stop, Smile has been developed. The size of the device makes it possible to be installed wherever you want. With M connection/s or cable and centralised mounting holes Smile is very easy to install, especially on aluminium extrusions. Smile is available for E-stops in both dynamic and static safety circuits i.e. for interfacing to Vital/ and Safety relays. Each version is available with either one or two M connections or cable. t the top of Smile, a LED shows the current status as: green = protection OK, red = this emergency stop has been pressed and if the LED is off, an emergency stop earlier in the loop has been actuated. Smile is also available with black push button and is used as a safety stop. See section on safety stops. Smile emergency stop has six different variants:. Smile 0E has a m cable connected through the base of the unit.. Smile 0EK has four m short connecting leads through the base of the unit. No LED.. Smile E has a five-pole M connector on one end of the unit.. Smile E has two five-pole M connectors, one on each end of the unit.. Smile ER has one -pole M connector at one end.. Smile ER has two -pole M connectors at each end. : www.jokabsafety.com

Connection examples Smile Smile 0E can be connected to either or a safety relay. Single channel example with LED indication. Safety category. The connection cable exits from underneath the unit. safety PLC +V (+) S Safety relay E.g. RT, RT9 Smile 0E Smile E can be connected to either or a safety relay. Single channel example with LED indication. Safety category. Connection via M connector. safety PLC +V Safety relay E.g. RT, RT9 Smile E can be connected to either or a safety relay. Single channel example with LED indication. Safety category. Connection via M connector + termination connector. S S (+) S S S Smile E Smile 0E can be connected to either or a safety relay. Two channel example with LED indication. Safety circuit category. safety PLC +V IQ 0 -pulse I (+) S Safety relay E.g. RT, RT9 Smile 0E Smile E can be connected to either or a safety relay. Two channel example with LED indication. Safety circuit category. Connection via M connector. safety PLC +V IQ 0 -pulse I Safety relay E.g. RT, RT9 S () S (+) S S Smile E can be connected to either or a safety relay. Two channel example with LED indication. Safety circuit category. Connection via M connector + termination connector. S S () S S S Smile E 7 8 safety PLC +V (+) S Safety relay E.g. RT, RT9 S S Smile E JST safety PLC +V IQ 0 -pulse I Safety relay E.g. RT, RT9 (+) S S () S S S Smile E JST 9 0 Smile E can be connected to either or a safety relay. Two channel serial connection example with LED indication. Safety circuit category. Connection via M connectors. Connection is made here without a termination device for Smile E (C), this unit is reconnected to the /safety relay via a separate cable. You can also use JST as a termination device after SmileE (C). safety PLC +V IQ 0 -pulse I +V IQ 0 -pulse I Safety relay E.g. RT, RT9 (+) S S () S S S (+) S S () S S S Smile E Smile E Smile E B B C www.jokabsafety.com :7 C

Connection examples Smile Smile E and E can be connected to either or safety relay. Two channel example with LED indication. Safety circuit category. Connection via M connectors. Note that there is no termination connector as the Smile E (C) completes the circuit without the need for a termination connector (JST) or return cable. safety PLC +V IQ 0 -pulse I (+) S Safety relay E.g. RT, RT9 S () S S S Smile E Smile E Smile E E-Stop Button status LED Indication The table shows the LED indication status of the E-Stop B C B C buttons from the example shown in above example. R R R G G G R R D G G Rd = Smile E R D R G Rd B B = Smile E R D D G Rd B C = Smile E R = Released D R R Rd B B D = Depressed D R D Rd B B G = Green light from the top of the button D D R Rd B B Rd = Red light from the top of the button D D D Rd B B Termination B = Blank, no light device JST Smile 0E/E/E are like any other emergency stops when to the LED indication is not connected. This means that any suitable Safety PLC or safety relay can be used. If the LED indication is used, the voltage between Pin (+) and Pin (-) should be between 9. 8.8 VDC. The following examples show connections to Safety PLC and Safety relay. B C Single channel PLC connection Two channel Safety relay connection Output Output PLC Safety Relay Output Input Input Smile E Input Smile E Brown White Blue Black Grey Smile 0E Brown White Black Grey Smile 0EK The cable is connected to Smile 0E via the lid at the back.. Input. Input. 0 VDC (to be connected only if LED indication is required). Output. Output Brown White Blue Black Grey Smile E (R) Brown White Blue Black Grey The leads are connected to Smile 0EK via the lid at the back. No LED connection. Brown Input White Input Black Output Grey Output Smile E (R) Brown White Blue Black Grey. Input. Input. 0 VDC (to be connected only if LED indication is required). Output. Output. Input. Input. 0 VDC (to be connected only if LED indication is required). Output, feedback. Output, feedback. Output. Output. 0 VDC. Input, feedback. Input, feedback :8 www.jokabsafety.com

Technical data Smile Manufacturer: rticle number/ ordering data: Smile 0E with m cable Smile 0EK with short connecting leads (No LED connection) Smile E with M male connector Smile E with male and female M connectors Smile ER Smile ER JST termination for Smile. Note. There are versions for dynamic technology (with Tina). Impact resistance (half sinusoidal) Vibration resistance (sinusoidal) Climate resistance Damp heat, cyclical Damp heat, sustained Dry heat Cooling Salt mist Level of safety: IEC/EN 08-...7 SIL PFH d : Colour: Weight: Size: Material: mbient temperature: BB B/Jokab Safety, Sweden TLJ000R000 TLJ000R000 TLJ000R0000 TLJ000R000 TLJ000R000 TLJ000R000 TLJ000R00 max. 0 m/s, pulse width ms, -axis, as per EN IEC 008--7 max. 0 m/s at 0 Hz, 0 cycles, -axis, as per EN IEC 008-- 9 hours, + C / 97%, + C / 9 % relative humidity, as per EN IEC 008--0 days, +0 C / 9 % relative humidity, as per EN IEC 008--78 9 hours, +70 C, as per EN IEC 008-- 9 hours, -0 C, as per EN IEC 008-- 9 hours, + C in a chemical solution with NaCl as per EN IEC 008--,0E-0 Protection class: IP Yellow, red and black pprox. grams Length: 8 mm + M contact(s) (. mm each) Width: 0 mm Height: mm Polyamide P, Macromelt, Polybutylentere phthalate PBT, Polypropylene PP, UL 9 V0-0 C to + C (operation), -0 C to +70 C (stock) Mounting: LED on E-Stop: Sign for emergency stop Two M recessed hexagon head screws, L mm. Hole cc: mm Green: Safety device ok, Safety circuit closed Off: Safety circuit broken (When an E-Stop is depressed all following units in the circuit lose the LED function). Red: Safety device actuator depressed and Safety circuit broken. Input voltage (LED): 7-7 VDC ripple ±0% (LED supply voltage) Current consumption (LED): E-Stop button ctuating force: ctuator travel: Material, contacts: Min current: Max current: Life, mechanical: ccessories: Emergency stop button S D F,,mm Emergency stop button E F T,,mm m ± N pprox. mm to latch Silver alloy gold plated 0 m 0 VDC/ 0 VC VDC, VC > 0 000 operationer TLJ000R0700 TLJ000R0800 Conformity: EN ISO 80, EN 00, EN 097-- & - 7 8 9 0 www.jokabsafety.com :9

Emergency stop with indication Smile Tina pprovals: CE RTI FIED BY pplication: To stop a machine or a process Features: Smile Tina - small and cost effective E-stop In order to fulfil the need for a small and easy to install E-stop, Smile has been developed. The size of the device makes it possible to be installed wherever you want. With M connections or cable and centralised mounting holes Smile is very easy to install, especially on aluminium extrusions. Smile is available for E-stops in both dynamic and static safety circuits i.e. for interfacing to Vital system/ safety PLC and Safety relays. Each version is available with either one or two M connections or cable. Two M connectors are used to enable the connection of E-stops in series, which is often used with dynamic safety circuits fulfilling safety category. In the top of the Smile Tina E-stop unit, LEDs show the actual status according to the dynamic system: Green = everything is OK, Red = E-stop activated. Flashing Red/Green = Stop activated from another preceding device. Smile is also available with black push button and used as a safety stop. See section on safety stops. The Smile Tina emergency stop is available in four versions:. Smile 0E Tina has a m cable connected via the base of the unit.. Smile E Tina has a five-pole M connector on the end of the unit for connecting the BB Jokab Safety cable.. Smile E Tina has two five-pole M connectors, one on each end of the unit for connecting the BB Jokab Safety cable.. Smile ER Tina has one -pole M connector at one end for connection of cable from BB Jokab Safety. Emergency push button up to cat. /PL e acc. to EN ISO 89- Light grids, emergency stop and Eden in the same safety loop together with Vital or gives cat. /PL e acc. to EN ISO 89- With LED indication on push button Robust Info-signal from each emergency stop Push button IP, housing IP7 vailable as safety stop (black push button) :0 www.jokabsafety.com

Connection examples Smile Tina Smile 0E Tina can be connected to either a or Vital system. Safety circuit category with LED indication/information. The connection cable exits from underneath the unit. IQ0 Vital T R Smile 0E Tina Smile E Tina can be connected to either a or Vital system. Safety circuit category with LED indication/information. Connection via M connectors. The circuit below shows three Smile E Tina units connected in series via connection terminals in the electrical cabinet. Electrical cabinet IQ0 Vital T R Connection termination Smile E Tina Smile E Tina Smile E Tina B C 7 8 Smile E Tina can be connected to either a or Vital system. Safety circuit category with LED indication/information. Connection via M connectors. The circuit below shows three Smile E Tina units and one Eden connected in series via a Tina connection block. IQ0 Vital Tina T R Smile E Tina Smile E Tina Smile E Tina B C 9 0 Eden = dam & Eva www.jokabsafety.com :

Connection examples Smile Tina E-Stop Button status Information output signal B C B C R R R H H H R R D H H L R R R H L H R R D H L L D R R L H H D R D L H L D D R L L H D D D L L L The table shows the information output signal status from each of the Smile E Tina units in the previous connection examples. In the example showing connection with an Eden sensor, the Eden status information signal acts in the same way as the Smile Tina E units. The status information signal can be connected to e.g. PLC input. Note. The information signal must not be used as a safety signal. The signal should only be used to indicate the status of connected devices. = Smile E Tina B = Smile E Tina C = Smile E Tina R = Released Smile E can be connected to either a or Vital system. Safety circuit category with LED indication/information. Connection via M connectors. The last Smile E Tina unit feeds the dynamic signal back to the /Vital. D = Depressed H = High (i.e. supply voltage) L = Low (= 0 VDC) B C IQ0 Vital T R Smile E Tina Smile E Tina Smile E Tina E-Stop Button status LED Indication B C B C R R R G G G R R D G G Rd R D R G Rd F R D D G Rd Rd D R R Rd F F D R D Rd F Rd D D R Rd Rd F D D D Rd Rd Rd The table shows the LED indication status of the E-Stop buttons in the previous connection examples, where three Smile 0 E, Smile E or E Tina units are connected in series. = Smile 0// E Tina B = Smile 0// E Tina C = Smile 0// E Tina R = Released D = Depressed G = Green light from the top of the button Rd = Red light from the top of the button F = Flashes between green and red light Smile E can be connected to either a or Vital system. Safety circuit category with LED indication/information. Connection via M connectors. The circuit shows two Smile E Tina s, one Eden sensor and one Focus Light Curtain connected in series. Eden = dam & Eva Focus IQ0 Vital T R Smile E Tina Smile E Tina M- M- M-B Tina 0 Brown White Blue Black Grey + - Smile 0E Tina. Input voltage,7-7 VDC ripple+/- 0%. Dynamic input signal. 0 VDC. Dynamic output signal. Information output The connection cable is connected to the Smile 0E Tina unit via the back panel. Brown White Blue Black Grey + - Smile E Tina Brown White Blue Black Grey + - Smile E Tina + - Brown White Blue Black Grey. Input voltage,7-7 VDC ripple+/- 0%. Dynamic input signal. 0 VDC. Dynamic output signal. Information output. Input voltage,7-7 VDC ripple+/- 0%. Dynamic input signal. 0 VDC. Not used. Not used. Output voltage to next unit. Dynamic output signal (To next Smile or to or Vital system). 0 VDC. Not used. Information output : www.jokabsafety.com

Technical data Smile Tina Manufacturer: rticle number/ ordering data: Smile 0E Tina with m connection cable Smile E Tina with M male connector Smile E Tina with male and female M connectors Smile ER Tina Note. There are versions for use with relay technology (without Tina). Impact resistance (half sinusoidal) Vibration resistance (sinusoidal) Climate resistance Damp heat, cyclical Damp heat, sustained Dry heat Cooling Salt mist Level of safety: IEC/EN 08-...7 SIL PFH d : Colour: Weight: Size: Material: mbient temperature: BB B/Jokab Safety, Sweden TLJ0000R000 TLJ0000R0000 TLJ0000R000 TLJ0000R000 max. 0 m/s, pulse width ms, -axis, as per EN IEC 008--7 max. 0 m/s at 0 Hz, 0 cycles, -axis, as per EN IEC 008-- 9 hours, + C / 97%, + C / 9 % relative humidity, as per EN IEC 008--0 days, +0 C / 9 % relative humidity, as per EN IEC 008--78 9 hours, +70 C, as per EN IEC 008-- 9 hours, -0 C, as per EN IEC 008-- 9 hours, + C in a chemical solution with NaCl as per EN IEC 008--,E-09 Protection class: IP Mounting: Yellow, red and black pprox. grams Length: 8 mm + M contact(s) (.mm each) Width: 0 mm Height: mm Polyamid P, Macromelt, Polybutylenterephthalate PBT, Polypropylen PP, UL 9 V0-0 C to + C (operation) -0 C to +70 C (stock) Two M hexagon socket screws, L mm. Hole centres: mm LED on E-Stop: Time delay: Sign for emergency stop Green: Safety device OK, Safety circuit OK Flashing: Safety device OK, safety circuit broken. Red: Breaks in safety device and safety circuit :. (Two Smile units are equal to three Edens in time delay) Input voltage: 7-7 VDC ripple ±0% Current consumption: Current from information output: E-Stop button ctuating force: ctuator travel: Material, contacts: Life, mechanical: ccessories: Emergency stop sign S D F,.mm Emergency stop sign E F T,.mm 7 m (7m with max. current from information output) 0 m max ± N pprox. mm to latch Silver alloy gold plated > 0 000 operations TLJ000R0700 TLJ000R0800 Conformity: EN ISO 80, EN 00, EN 097-- & - 7 8 9 0 www.jokabsafety.com :

Emergency stop with indication Smile S-i pprovals: CE RTI FIED BY pplication: To stop a machine or a process Safe input node in S-i systems Features: Smile E S-i is an emergency stop with a built-in dual channel safe S-i input node. The S-i bus and the safety around it is specified by the two organisations S-International ssociation and S-Interface Safety at Work, and is described in publications such as S-Interface The utomatic Solution. Smile E S-i is supplied with 0 V DC from the S-i bus. The recommended connection to the S-i bus is made via a flat cable terminal to M (see Figure), which makes it possible to quickly and easily connect the device to the yellow S-i cable. Smile S-i can also be connected directly to the S-i bus using only two conductors (pins and on the unit's M contact). Smile is also available with black push button and is used in this case as a safety stop. See section on safety stops. Emergency push button up to cat. /PL e acc. to EN ISO 89- Simple connection to S-i bus With LED indication on push button and S-i status indication Robust Push button IP, housing IP7 vailable as safety stop (black push button) : www.jokabsafety.com

Technical data Smile S-i Manufacturer: rticle number/ ordering data: Smile E S-i BB B/Jokab Safety, Sweden TLJ000R0000 S-i data S-i profile S-7.B.0 ddressing M-contact Node address on delivery 0 Response time across the S-i bus ms (+ response time for safety monitor) Pin configuration () S-i + () Not used () S-i () Not used () Not used Voltage supply Output voltage Total current consumption < 0 m 0 V DC from the S-i bus. Tolerance.. V DC. General Enclosure protection class IP mbient temperature - +0 C Dimensions x 0 x 8 (+, mm M contact) (H x B x D) Colour Base: Yellow Emergency stop button (Smile E S-i): Red Safe stop button (Smile S S-i): Black ctuating force ± N ctuating movement Ca mm till lås Mechanical life > 0 000 operationer PFH d,9x0-9 Safety/Harmonised standards IEC/EN 08-..7 SIL, PFDavr:,9x0 - EN 0 SIL EN ISO 89- Performance level PL e, Category, MTTF d : high EN 097-- & - For emergency stop buttons/ safety stop buttons EN ISO 80:008 For emergency stop buttons/ safety stop buttons Certification TÜV Nord Push button control panel LED in emergency stop button LED displays can be individually programmed in the PLC program as shown below. LED in pushbutton Indicator Description Red ON Output bit ON OFF Output bit OFF or Output bit & ON Green ON Output bit ON OFF Output bit OFF or Output bit & ON S-i LED and Fault LED in combination LED pair at the M contact. S-i (Green) Fault (Red) OFF OFF S-i voltage missing ON OFF Normal operation ON ON No data exchange with master Flash ON No data exchange due to address = 0 7 8 9 0 Smile xxxx-x with one S-i node for four pushbuttons. Smile Exxxx-x with one S-i safety node for e-stop and one S-i node for three pushbuttons. Smile EKxxxx-x with two safety nodes (e-stop and mode selector) and one S-i node for two pushbuttons. www.jokabsafety.com :

Emergency stop Grab Wire Safety Switch Stop-Line pprovals: BG pplication: Emergency stop Grab Wire Safety Switch along machines or conveyors Features: Duplicate extraction in two directions Up to 7 m length Robust IP 7 Integrated emergency stop button Warned before the safety circuit is broken Duplicated safety in both directions Stop-Line is used for easy reach of an emergency stop along machines, conveyors and processes. Stop-Line is easier to install than a system of several emergency stop buttons along a carriage path. Stop-Line indicates operation status, reset or triggered mode. There is also indication of how taut the wire is. Stop-Line can be used as protection for conveyors with low risks. The wire can, for example, be installed at waist height in front of the conveyor, which provides an emergency stop if someone falls towards the conveyor. Stop-Line has four contacts. If someone pulls the wire or if the wire is broken, all the contacts are affected. In both cases, the machine is emergency-stopped. Just before the safety contacts are broken an indication is given since the wire may accidentally trigger the stop signal as a result of temperature differences. To reset the Stop-Line the combined emergency- and reset button must be pulled out. Forced Disconnected Contacts The contacts of the Stop-Line are forced-disconnected. Forced disconnection means that the contacts are mechanically pulled apart, thus ensuring protection against contact welding or sticking. Safety level The forced disconnected contacts provide a high level of safety. To achieve a high level of safety in respect to the connection with the machine control system, it is appropriate to use a safety relay manufactured by BB Jokab Safety. Stop-Line can be combined with Tina devices for use in a safety circuit containing other safety devices and emergency stops according to PL e. Regulations and Standards The Stop-Line is designed and approved in accordance with relevant standards. See technical data. Emergency-stop Grab Wire easily accessible during normal work operation along a machine : www.jokabsafety.com

Technical data Stop-Line Manufacturer: rticle number/ Ordering data Stop-Line 7 Stop-Line 7 Stop-Line 7B Stop-Line 7B Colour Mounting Stop-Line The wire should be mounted at least 0 mm from the underlying surface. If the wire is longer than m it must be supported with low friction supports. The ambient temperature during installation should be the same as during operation. For the Stop-Line type.. fter installation, pull the wire strongly several times and then adjust the tension to compensate for any extensions due to deformation of the thimbles. Stop-Line 7/7 BB B/Jokab Safety, Sweden TLJ000R0000 TLJ000R0000 TLJ000R000 TLJ000R000 Black with yellow label Level of safety Cat. /PL e, EN ISO 89- Housing Material Lid Material Operating temperature Switching contacts Cast aluminium Cast aluminium -0 C to +80 C NC + NO Protection class IP 7, EN 09 Mechanical life Max. switching frequency Reset method 00 000 switching cycles 0/min Max. wire length 7, m./7 m. Mounting Terminals mushroom-head slam button x M/ x M Screw terminal, 8 x M Cable access x M0 x. Weight Max. voltage Information output Rated voltage Rated current Thermal current 0,9 kg 0 VC Ue 0-0 V DC Ie 0m 0 Utilisation category C, DC Short-circuit protection Melting Fuse DII type gg Conformity EN ISO 89-, EN ISO 80, EN097-, EN 097--, VDE 0, EN ISO 00-, - och VDE 00 T00. Support (Pulley block or Eye bolt) Support Max 7m/7m 0,m -m 0,m Pull rope spring 7 8 9 0 www.jokabsafety.com :7

Contact djustment Stop-Line The tension is adjusted using the built-in set screw until the arrowhead is aligned with the label in the window (see picture below). When the combined emergency- and reset button is then pulled making the status window show green, all contact pairs are in operational mode and the machine can be started. Pulling the wire, or if the wire is broken, all the contact pairs shift position and the machine is stopped. Before doing so, an electronic warning signal is provided which can be used to alert an operator to compensate for slow variations of the tension in the Stop-Line wire. This is useful to avoid unnecessary stops caused by e.g. ambient temperature variations. Tolerance: distance ± 0. mm, power ± % on (closed) off (open) for contacts - S Electrical Connection Stop-Line Electrical connection of Stop-Line, highest level of safety. Connection terminal and : Connection of supply voltage 0- DC Connection terminal and : Connection to signal circuit or lamp for indication Note! The connection shows the Stop-Line in a correctly tensioned condition. :8 www.jokabsafety.com

Ordering data Stop-Line accessories Installation kit Installation kit Wire mm (sheath mm) Wire clamp for mm Thimble Turnbuckle Swivel Eye bolt Mx0 Eye bolt M8x0 Pull wire spring QF 7 Pull wire spring QF 7 Pulley block, unhinged Fastener for pulley block Pulley block, hinged Deflection pulley Ø 7mm Nut M TLJ000R00 Contents: TLJ000R000 x Wire TLJ000R000 x Wire clamp TLJ000R000 x Thimble TLJ000R000 x Turnbuckle TLJ000R0900 x 8 Eye bolt M8x0 TLJ000R00 Contents: TLJ000R000 x 0 Wire TLJ000R000 x Pull wire spring TLJ000R000 x 9 Pullay block TLJ000R000 x 9 Fastener for pulley block TLJ000R000 TLJ000R000 TLJ000R000 TLJ000R000 TLJ000R00 TLJ000R000 TLJ000R0900 TLJ000R0000 TLJ000R000 TLJ000R000 TLJ000R000 TLJ000R000 TLJ000R000 TLJ000R000 7 8 9 0 www.jokabsafety.com :9

Safety stop Inca and Smile When should I use the safety stop? Safety stops are used to stop the operation of a machine in a safe manner. It must not be used as an emergency stop, but only as a stop for an individual hazardous motion. This is indicated by black push button. Likewise, an emergency stop push button with red push button must not be used as a safety stop. Inca for panel mounting The Inca series is available with black push button and is called Inca S/Inca S Tina. The safety stop is identical to the corresponding emergency stop apart from the black push button. For technical data see the Inca emergency stop. Smile with indication The Smile series is available with black push button and has a similar designation apart from an S in the name instead of E. The safety stops are identical to the corresponding emergency stops apart from the black push button. For technical data see the Smile emergency stop. rticle number TLJ000R000 TLJ000R000 Ordering data INC S INC S Tina rticle number Ordering data TLJ000R0900 Smile S TLJ000R000 Smile S TLJ000R00 Smile SR TLJ0000R000 Smile S Tina TLJ0000R000 Smile S Tina TLJ0000R0700 Smile SR Tina TLJ0000R0800 Smile SR Tina TLJ000R000 Smile S S-i :0 www.jokabsafety.com

Reset button Smile R When do I need reset push button? Smile R/B are reset Push buttons intended to reset safety circuits. Smile R has a connections for the NO-contact and for the LED in the PB. The reset LED is o be turned of after reset of the safety circuit. Smile RB is used together with our Safety Plc in order to reduce the numder of terminals, on terminal is used as both input for the reset as well as output for the LED. 7 Technical data Smile R Manufacturer rticle number/ ordering data Smile R Smile RB Colour Base Pushbutton Material Housing Pushbutton contact BB B/Jokab Safety, Sweden TLJ000R0000 TLJ000R000 yellow blue Polyprobylene PP u mbient temperature Humidity range Protection class Connectors Size Weight Mechanical life Switching reliability -...+ C to 8% (with no icing or condensation) IP -pole male M connector 8x0x (LxWxH) + mm for M connector (L) aprox. 0 g.000.000 operations at 0 m/ VDC 0 x 0 - at m/ VDC 8 9 0 Power Supply LED operating voltage LED current consumption Pushbutton operating voltage Pushbutton current consumption Pushbutton rated power VDC (maximum VDC) 0 m at VDC 0 m at VDC Min: V, max: V Min: M, max 00 m Max: 0 mw www.jokabsafety.com :