Rev.2.2_ HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR The is a positive voltage regulator with a low dropout voltage, high output voltage accuracy, and low current consumption developed based on CMOS technology. A built-in low on-resistance transistor provides a low dropout voltage and large output current, and a built-in overcurrent protector prevents the load current from exceeding the current capacitance of the output transistor. An ON/OFF circuit ensures a long battery life. Compared with the voltage regulators using the conventional CMOS process, a larger variety of capacitors are available, including small ceramic capacitors. Small SOT- 23-5 and 5-Pin SON(A) packages realize highdensity mounting. The lineup includes the S-1112 and S-1122 Series, which differ in pin configuration. Features Output voltage: 1.5 V to 5.5 V, selectable in.1 V steps. High-accuracy output voltage: ±1.% Low dropout voltage: 19 mv typ. (3. V output product, I OUT = 1 ma) Low current consumption: During operation: 5 µa typ., 9 µa max. During shutdown:.1 µa typ., 1. µa max. High peak current capability: 15 ma output is possible (@ V IN V OUT(S) + 1. V) *1 Built-in ON/OFF circuit: Ensures long battery life. Low ESR capacitor can be used: A ceramic capacitor of.47 µf or more can be used for the output capacitor. High ripple rejection: 8 db typ. (@ 1. khz) Built-in overcurrent protector: Overcurrent of output transistor can be restricted. Small package: SOT-23-5, 5-Pin SON(A) *1. Attention should be paid to the power dissipation of the package when the output current is large. Applications Power supply for battery-powered devices Power supply for personal communication devices Power supply for home electric/electronic appliances Power supply for cellular phones Packages SOT-23-5 5-Pin SON(A) (Package drawing code: MP5-A) (Package drawing code: PN5-A) Seiko Instruments Inc. 1
Block Diagram Rev.2.2_ *1 VIN VOUT Overcurrent protector ON/OFF ON/OFF circuit + Reference voltage circuit VSS *1. Parasitic diode Figure 1 2 Seiko Instruments Inc.
Rev.2.2_ Product Code Structure The product types and output voltage for the can be selected at the user s request. Refer to the Product name for the meanings of the characters in the product name and Product name list for the full product names. 1. Product name (S-1112 Series) S-1112 x xx xx xxx TF IC direction in tape specifications *1 *1. Refer to the taping specifications at the end of this book. *2. Refer to the product name list. *3. Refer to 3. Shutdown (ON/OFF pin) under the Operation. Product name (abbreviation) *2 Package name (abbreviation) MC: SOT-23-5 PN: 5-Pin SON(A) Output voltage 15 to 55 (E.g., when the output voltage is 1.5 V, it is expressed as 15.) Product type *3 A: ON/OFF pin negative logic B: ON/OFF pin positive logic 2. Product name list (S-1112 Series) Table 1 Output Voltage SOT-23-5 5-Pin SON(A) 1.5 V ±1.% S-1112B15MC-L6A-TF S-1112B15PN-L6A-TF 1.8 V ±1.% S-1112B18MC-L6D-TF S-1112B18PN-L6D-TF 2.5 V ±1.% S-1112B25MC-L6K-TF S-1112B25PN-L6K-TF 2.6 V ±1.% S-1112B26MC-L6L-TF S-1112B26PN-L6L-TF 2.7 V ±1.% S-1112B27MC-L6M-TF S-1112B27PN-L6M-TF 2.8 V ±1.% S-1112B28MC-L6N-TF S-1112B28PN-L6N-TF 2.9 V ±1.% S-1112B29MC-L6O-TF S-1112B29PN-L6O-TF 3. V ±1.% S-1112B3MC-L6P-TF S-1112B3PN-L6P-TF 3.1 V ±1.% S-1112B31MC-L6Q-TF S-1112B31PN-L6Q-TF 3.3 V ±1.% S-1112B33MC-L6S-TF S-1112B33PN-L6S-TF 5. V ±1.% S-1112B5MC-L7J-TF S-1112B5PN-L7J-TF Remark Please contact the SII marketing department for products with an output voltage other than those specified above or type A products. Seiko Instruments Inc. 3
Rev.2.2_ 3. Product name (S-1122 Series) S-1122 x xx xx xxx TF IC direction in tape specifications *1 *1. Refer to the taping specifications at the end of this book. *2. Refer to the product name list. *3. Refer to 3. Shutdown pin (ON/OFF pin) under the Operation. Product name (abbreviation) *2 Package name (abbreviation) MC: SOT-23-5 PN: 5-Pin SON(A) Output voltage 15 to 55 (E.g., when the output voltage is 1.5 V, it is expressed as 15.) Product type *3 A: ON/OFF pin negative logic B: ON/OFF pin positive logic 4. Product name list (S-1122 Series) Table 2 Output Voltage SOT-23-5 5-Pin SON(A) 1.5 V ±1.% S-1122B15MC-L8A TF S-1122B15PN-L8A TF 1.8 V ±1.% S-1122B18MC-L8D TF S-1122B18PN-L8D TF 2.5 V ±1.% S-1122B25MC-L8K TF S-1122B25PN-L8K TF 2.6 V ±1.% S-1122B26MC-L8L TF S-1122B26PN-L8L TF 2.7 V ±1.% S-1122B27MC-L8M TF S-1122B27PN-L8M TF 2.8 V ±1.% S-1122B28MC-L8N TF S-1122B28PN-L8N TF 2.9 V ±1.% S-1122B29MC-L8O TF S-1122B29PN-L8O TF 3. V ±1.% S-1122B3MC-L8P TF S-1122B3PN-L8P TF 3.1 V ±1.% S-1122B31MC-L8Q TF S-1122B31PN-L8Q TF 3.3 V ±1.% S-1122B33MC-L8S TF S-1122B33PN-L8S TF 5. V ±1.% S-1122B5MC-L9J TF S-1122B5PN-L9J TF Remark Please contact the SII marketing department for products with an output voltage other than those specified above or type A products. 4 Seiko Instruments Inc.
Rev.2.2_ Pin Configuration SOT-23-5 Top view 5 4 Table 3 (S-1112 Series) Pin No. Symbol Description 1 VIN Input voltage pin 2 VSS GND pin 3 ON/OFF Shutdown pin 4 NC *1 No connection 5 VOUT Output voltage pin *1. The NC pin is electrically open. The NC pin can be connected to VIN or VSS. 1 2 3 Table 4 (S-1122 Series) Pin No. Symbol Description 1 VOUT Output voltage pin 2 VSS GND pin Figure 2 3 VIN Input voltage pin 4 ON/OFF Shutdown pin 5 NC *1 No connection *1. The NC pin is electrically open. The NC pin can be connected to VIN or VSS. Seiko Instruments Inc. 5
Rev.2.2_ 5-Pin SON(A) Top view 5 4 Table 5 (S-1112 Series) Pin No. Symbol Description 1 ON/OFF Shutdown pin 2 VSS GND pin 3 VIN Input voltage pin 4 VOUT Output voltage pin 5 NC *1 No connection 1 2 3 *1. The NC pin is electrically open. The NC pin can be connected to VIN or VSS. Table 6 (S-1122 Series) Pin No. Symbol Description 1 VOUT Output voltage pin 2 VSS GND pin Figure 3 3 NC *1 No connection 4 ON/OFF Shutdown pin 5 VIN Input voltage pin *1. The NC pin is electrically open. The NC pin can be connected to VIN or VSS. Absolute Maximum Ratings Table 7 (Ta = 25 C unless otherwise specified) Item Symbol Absolute Maximum Rating Unit Input voltage V IN V SS.3 to V SS + 7 V V ON/OFF V SS.3 to V IN +.3 Output voltage V OUT V SS.3 to V IN +.3 Power dissipation P D SOT-23-5 3 mw 5-Pin SON(A) 15 Operating ambient temperature T opr 4 to +85 C Storage ambient temperature T stg 4 to +125 Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. 6 Seiko Instruments Inc.
Rev.2.2_ Electrical Characteristics Table 8 (Ta = 25 C unless otherwise specified) Item Symbol Conditions Min. Typ. Max. Unit Test Circuit Output voltage *1 V OUT(E) V IN = V OUT(S) + 1. V, I OUT = 3 ma V OUT(S) V OUT(S) V OUT(S).99 1.1 V 1 Output current *2 I OUT V IN V OUT(S) + 1. V 15 *5 ma 3 Dropout voltage *3 V drop I OUT = 1 ma 1.5 V V OUT(S) 1.6 V.32.55 V 1 1.7 V V OUT(S) 1.8 V.28.47 1.9 V V OUT(S) 2.3 V.25.35 2.4 V V OUT(S) 2.7 V.2.29 2.8 V V OUT(S) 5.5 V.19.26 VOUT1 VOUT(S) +.5 V V IN 6.5 V, Line regulation.5.2 % / V VIN VOUT I OUT = 3 ma Load regulation V OUT2 V IN = V OUT(S) + 1. V, 1. ma I OUT 8 ma 12 4 mv Output voltage VOUT V IN = V OUT(S) + 1. V, I OUT = 1 ma, ppm temperature coefficient *4 ±1 Ta VOUT 4 C Ta 85 C / C Current consumption during operation Current consumption during shutdown I SS1 I SS2 V IN = V OUT(S) + 1. V, ON/OFF pin = ON, no load V IN = V OUT(S) + 1. V, ON/OFF pin = OFF, no load 5 9 µa 2.1 1. Input voltage V IN 2. 6.5 V Shutdown pin input voltage H V SH V IN = V OUT(S) + 1. V, R L = 1. kω 1.5 4 Shutdown pin input voltage L V SL V IN = V OUT(S) + 1. V, R L = 1. kω.3 Shutdown pin input current H I SH V IN = 6.5 V, V ON/OFF = 6.5 V.1.1 µa Shutdown pin input current L I SL V IN = 6.5 V, V ON/OFF = V.1.1 Ripple rejection RR V IN = V OUT(S) + 1. V, f = 1. khz, V rip =.5 Vrms, I OUT = 3 ma 8 db 5 Short-circuit current I short V IN = V OUT(S) + 1. V, ON/OFF pin = ON, V OUT = V 2 ma 3 *1. V OUT(S): Specified output voltage V OUT(E): Actual output voltage at the fixed load The output voltage when fixing I OUT(= 3 ma) and inputting V OUT(S) + 1. V *2. The output current at which the output voltage becomes 95% of V OUT(E) after gradually increasing the output current. *3. V drop = V IN1 (V OUT3.98) V OUT3 is the output voltage when V IN = V OUT(S) + 1. V and I OUT = 1 ma. V IN1 is the input voltage at which the output voltage becomes 98% of V OUT3 after gradually decreasing the input voltage. *4. The change in temperature [mv/ C] is calculated using the following equation. VOUT *1 *2 VOUT * [ mv/ C] = VOUT(S) [ V] [ ppm/ C] 3 1 Ta Ta VOUT *1. The change in temperature of the output voltage *2. Specified output voltage *3. Output voltage temperature coefficient *5. The output current can be at least this value. Due to restrictions on the package power dissipation, this value may not be satisfied. Attention should be paid to the power dissipation of the package when the output current is large. This specification is guaranteed by design. Seiko Instruments Inc. 7
Rev.2.2_ Test Circuits 1. VIN ON/OFF Set to power ON VOUT VSS V + + A Figure 4 2. A VIN VOUT ON/OFF VSS Set to V IN or GND Figure 5 3. VIN VOUT + A ON/OFF Set to power ON VSS + V Figure 6 4. VOUT VIN + + A ON/OFF V R L VSS Figure 7 5. VIN ON/OFF Set to Power ON VOUT VSS V + RL Figure 8 8 Seiko Instruments Inc.
Rev.2.2_ Standard Circuit Input VIN VOUT Output *1 *2 C IN ON/OFF C L VSS Single GND GND *1. C IN is a capacitor for stabilizing the input. *2. A ceramic capacitor of.47 µf or more can be used for C L. Figure 9 Caution The above connection diagram and constant will not guarantee successful operation. Perform thorough evaluation using the actual application to set the constant. Application Conditions Input capacitor (C IN ): Output capacitor (C L ): ESR of output capacitor: 1. µf or more.47 µf or more 1 Ω or less Caution A general series regulator may oscillate, depending on the external components selected. Check that no oscillation occurs with the application using the above capacitor. Seiko Instruments Inc. 9
Explanation of Terms Rev.2.2_ 1. Low dropout voltage regulator The low dropout voltage regulator is a voltage regulator whose dropout voltage is low due to its built-in low on-resistance transistor. 2. Low ESR A capacitor whose ESR (Equivalent Series Resistance) is low. The enables use of a low ESR capacitor, such as a ceramic capacitor, for the output-side capacitor C L. A capacitor whose ESR is 1 Ω or less can be used. 3. Output voltage (V OUT ) The accuracy of the output voltage is ensured at ±1.% under the specified conditions of fixed input voltage *1, fixed output current, and fixed temperature. *1. Differs depending the product. Caution If the above conditions change, the output voltage value may vary and exceed the accuracy range of the output voltage. Please see the electrical characteristics and attached characteristics data for details. VOUT1 4. Line regulation VIN VOUT Indicates the dependency of the output voltage on the input voltage. That is, the values show how much the output voltage changes due to a change in the input voltage with the output current remaining unchanged. 5. Load regulation ( V OUT2 ) Indicates the dependency of the output voltage on the output current. That is, the values show how much the output voltage changes due to a change in the output current with the input voltage remaining unchanged. 6. Dropout voltage (V drop ) Indicates the difference between the input voltage V IN1, which is the input voltage (V IN ) at the point where the output voltage has fallen to 98% of the output voltage value V OUT3 after V IN was gradually decreased from V IN = V OUT(S) + 1. V, and the output voltage at that point (V OUT3.98). V drop = V IN1 (V OUT3.98) 1 Seiko Instruments Inc.
Rev.2.2_ VOUT 7. Temperatur e coefficient of output voltage Ta VOUT The shadowed area in Figure 1 is the range where V OUT varies in the operating temperature range when the temperature coefficient of the output voltage is ±1 ppm/ C. Ex. S-1112/1122B28 Typ. V OUT [V] +.28 mv / C V OUT(E) *1.28 mv / C 4 25 85 Ta [ C] *1. V OUT(E) is the value of the output voltage measured at 25 C. Figure 1 A change in the temperature of the output voltage [mv/ C] is calculated using the following equation. VOUT *1 *2 VOUT * [ mv/ C] = VOUT(S) [ V] [ ppm/ C] 3 1 Ta Ta VOUT *1. Change in temperature of output voltage *2. Specified output voltage *3. Output voltage temperature coefficient Seiko Instruments Inc. 11
Operation Rev.2.2_ 1. Basic operation Figure 11 shows the block diagram of the. The error amplifier compares the reference voltage (V ref ) with V fb, which is the output voltage resistancedivided by feedback resistors R s and R f. It supplies the output transistor with the gate voltage necessary to ensure a certain output voltage free of any fluctuations of input voltage and temperature. VIN Current supply Error amplifier *1 VOUT V ref + R f V fb Reference voltage circuit R s VSS *1. Parasitic diode Figure 11 2. Output transistor The uses a low on-resistance P-channel MOS FET as the output transistor. Be sure that V OUT does not exceed V IN +.3 V to prevent the voltage regulator from being damaged due to inverse current flowing from VOUT pin through a parasitic diode to VIN pin. 12 Seiko Instruments Inc.
Rev.2.2_ 3. Shutdown pin (ON/OFF pin) This pin starts and stops the regulator. When the ON/OFF pin is set to the shutdown level, the operation of all internal circuits stops, and the builtin P-channel MOS FET output transistor between the VIN pin and VOUT pin is turned off to substantially reduce the current consumption. The VOUT pin becomes the V SS level due to the internally divided resistance of several MΩ between the VOUT pin and VSS pin. The structure of the ON/OFF pin is as shown in Figure 12. Since the ON/OFF pin is neither pulled down nor pulled up internally, do not use it in the floating state. In addition, note that the current consumption increases if a voltage of.3 V to V IN.3 V is applied to the ON/OFF pin. When the ON/OFF pin is not used, connect it to the VSS pin if the logic type is A and to the VIN pin if it is B. Table 9 Logic Type ON/OFF Pin Internal Circuits VOUT Pin Voltage Current Consumption A L : Power on Operating Set value I SS1 A H : Power off Stopped V SS level I SS2 B L : Power off Stopped V SS level I SS2 B H : Power on Operating Set value I SS1 VIN ON/OFF VSS Figure 12 Selection of Output Capacitor (C L ) The requires an output capacitor between the VOUT and VSS pins for phase compensation. A ceramic capacitor with a capacitance of.47 µf or more can be used. Even if using an OS capacitor, tantalum capacitor, or aluminum electrolytic capacitor, a capacitance of.47 µf or more and an ESR of 1 Ω or less are required. The value of the output overshoot or undershoot transient response varies depending on the value of the output capacitor. When selecting the output capacitor, perform sufficient evaluation, including evaluation of temperature characteristics, on the actual device. Seiko Instruments Inc. 13
Precautions Rev.2.2_ Wiring patterns for the VIN, VOUT and GND pins should be designed so that the impedance is low. When mounting an output capacitor between the VOUT and VSS pins (C L ) and a capacitor for stabilizing the input between VIN and VSS pins (C IN ), the distance from the capacitors to these pins should be as short as possible. Note that the output voltage may increase when a series regulator is used at low load current (1. ma or less). Generally a series regulator may cause oscillation, depending on the selection of external parts. The following conditions are recommended for this IC. However, be sure to perform sufficient evaluation under the actual usage conditions for selection, including evaluation of temperature characteristics. Input capacitor (C IN ): 1. µf or more Output capacitor (C L ):.47 µf or more Equivalent series resistance (ESR): 1 Ω or less The voltage regulator may oscillate when the impedance of the power supply is high and the input capacitor is small or an input capacitor is not connected. The application conditions for the input voltage, output voltage, and load current should not exceed the package power dissipation. Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic protection circuit. In determining the output current, attention should be paid to the output current value specified in Table 8 in the electrical characteristics and footnote *5) of the table. SII claims no responsibility for any disputes arising out of or in connection with any infringement by products including this IC of patents owned by a third party. 14 Seiko Instruments Inc.
Rev.2.2_ Typical Characteristics Remark The following, which describes the S-1112 Series as the typical product, shows typical data common to the S-1122 Series. (1) Output Voltage vs. Output current (when load current increases) S-1112B15 (Ta = 25 C) 1.8 1.6 1.4 1.2 6.5 V 1. V IN = 1.8 V.8.6.4.2 2.5 V 1 2 3 4 5 6 S-1112B3 (Ta = 25 C) 3.5 3. 2.5 V IN = 3.3 V 2. 6.5 V 1.5 1..5 4. V 1 2 3 4 5 6 S-1112B5 (Ta = 25 C) IOUT [ma] IOUT [ma] 6 5 4 3 V IN = 5.3 V 6. V 2 1 6.5 V 1 2 3 4 IOUT [ma] (2) Output voltage vs. Input voltage 5 6 Remark In determining the output current, attention should be paid to the following. 1) The minimum output current value and footnote *5 in the electrical characteristics 2) The package power dissipation S-1112B15 (Ta = 25 C) S-1112B3 (Ta = 25 C) 1.6 3.1 1.5 3. 1.4 1.3 1.2 1.1 I OUT = 1 ma 3 ma 5 ma 2.9 2.8 2.7 2.6 I OUT = 1 ma 3 ma 5 ma 1. 1. 1.5 2. 2.5 3. 3.5 2.5 2.5 3. 3.5 4. 4.5 5. S-1112B5 (Ta = 25 C) VIN [V] VIN [V] 5.5 5. 4.5 4. 3.5 3. I OUT = 1 ma 5 ma 3 ma 2.5 2. 3. 4. 5. 6. 7. VIN [V] Seiko Instruments Inc. 15
Rev.2.2_ (3) Dropout voltage vs. Output current S-1112B15 S-1112B3 Vdrop [V].45.4.35 85 C 25 C.3.25.2.15.1.5 5 1 4 C 15 2 Vdrop [V].45.4.35.3 85 C 25 C.25.2.15.1.5 5 1 4 C 15 2 IOUT [ma] IOUT [ma] S-1112B5 Vdrop [V].45.4.35.3 85 C 25 C.25.2.15.1.5 5 1 4 C 15 2 IOUT [ma] (4) Dropout voltage vs. Set output voltage Vdrop [V].4.35.3.25.2.15.1.5 15 ma 1 ma 5 ma 3 ma 1 ma 1 2 3 4 5 6 7 VOTA [V] 16 Seiko Instruments Inc.
Rev.2.2_ (5) Output voltage vs. Ambient temperature S-1112B15 S-1112B3 1.6 1.55 1.5 1.45 1.4 5 25 25 5 75 1 3.2 3.15 3.1 3.5 3. 2.95 2.9 2.85 2.8 5 25 25 5 75 1 Ta [ C] Ta [ C] S-1112B5 5.3 5.2 5.1 5. 4.9 4.8 4.7 5 25 25 5 75 1 Ta [ C] (6) Current consumption vs. Input voltage S-1112B15 S-1112B3 12 12 ISS1 [µa] 1 8 6 4 2 85 C 25 C 4 C ISS1 [µa] 1 8 6 4 2 25 C 4 C 85 C 2 4 6 8 2 4 6 8 VIN [V] VIN [V] S-1112B5 12 ISS1 [µa] 1 25 C 8 6 4 C 4 85 C 2 2 4 6 8 VIN [V] Seiko Instruments Inc. 17
Rev.2.2_ (7) Ripple rejection S-1112B15 (Ta = 25 C) S-1112B3 (Ta = 25 C) VIN = 2.5 V, COUT =.47 µf VIN = 4. V, COUT =.47 µf Ripple Rejection [db] 1 8 6 4 2 1 5 ma IOUT = 1 ma 3 ma 1 1k 1k 1k 1M Ripple Rejection [db] 1 8 6 4 2 1 5 ma IOUT = 1 ma 3 ma 1 1k 1k 1k 1M Frequency [Hz] Frequency [Hz] S-1112B5 (Ta = 25 C) VIN = 6. V, COUT =.47 µf 1 Ripple Rejection [db] 8 6 4 2 1 5 ma IOUT = 1 ma 3 ma 1 1k 1k 1k 1M Frequency [Hz] 18 Seiko Instruments Inc.
Rev.2.2_ Reference Data (1) Input transient response characteristics S-1112B15 (Ta = 25 C) S-1112B3 (Ta = 25 C) IOUT = 3 ma, tr = tf = 5. µs, COUT =.47 µf, CIN = µf IOUT = 3 ma, tr = tf = 5. µs, COUT =.47 µf, CIN = µf 1.62 1.6 1.58 1.56 1.54 1.52 1.5 1.48 1.46 V IN V OUT -4-2 2 4 6 8 1 12 14 16 4. 3.5 3. 2.5 2. 1.5 1..5 VIN [V] 3.8 3.6 3.4 3.2 3. 2.98 2.96 V IN V OUT -4-2 2 4 6 8 1 12 14 16 6 5 4 3 2 1 VIN [V] S-1112B5 (Ta = 25 C) t [µs] IOUT = 3 ma, tr = tf = 5. µs, COUT =.47 µf, CIN = µf t [µs] 5.12 5.1 5.8 5.6 5.4 5.2 5. 4.98 4.96 V IN V OUT -4-2 2 4 6 8 1 12 14 16 8 7 6 5 4 3 2 1 VIN [V] t [µs] (2) Load transient response characteristics S-1112B15 (Ta = 25 C) VIN = 2.5 V, COUT =.47 µf, CIN = 1. µf, IOUT = 5 1 ma S-1112B3 (Ta = 25 C) VIN = 4. V, COUT =.47 µf, CIN = 1. µf, IOUT = 5 1 ma 1.7 15 3.2 15 1.65 1.6 1.55 1.5 1.45 1.4 I OUT V OUT 1 5 5 1 15-4 -2 2 4 6 8 1 12 14 16 IOUT [ma] 3.15 1 I OUT 3.1 5 3.5 V OUT 3. 5 2.95 1 2.9 15-4 -2 2 4 6 8 1 12 14 16 IOUT [ma] S-1112B5 (Ta = 25 C) t [µs] VIN = 6. V, COUT =.47 µf, CIN = 1. µf, IOUT = 5 1 ma t [µs] 5.2 5.15 5.1 5.5 5. 4.95 4.9 I OUT V OUT 15 1 5 5 1 15-4 -2 2 4 6 8 1 12 14 16 IOUT [ma] t [µs] Seiko Instruments Inc. 19
Rev.2.2_ (3) Shutdown pin transient response characteristics S-1112B15 (Ta = 25 C) VIN = 2.5 V, COUT =.47 µf, CIN = 1. µf, IOUT = 1 ma S-1112B3 (Ta = 25 C) VIN = 4. V, COUT =.47 µf, CIN = 1. µf, IOUT = 1 ma 5 3 1 6 4 2 8 4 3 2 1 V OUT V ON/OFF 1 1 2 VON/OFF [V] 6 4 2 V OUT V ON/OFF 2 2 4 VON/OFF [V] 1 -.4 -.2.2.4.6.8 1. 1.2 1.4 1.6 3 2 -.4 -.2.2.4.6.8 1. 1.2 1.4 1.6 6 t [ms] t [ms] 2 Seiko Instruments Inc.
The information described herein is subject to change without notice. Seiko Instruments Inc. is not responsible for any problems caused by circuits or diagrams described herein whose related industrial properties, patents, or other rights belong to third parties. The application circuit examples explain typical applications of the products, and do not guarantee the success of any specific mass-production design. When the products described herein are regulated products subject to the Wassenaar Arrangement or other agreements, they may not be exported without authorization from the appropriate governmental authority. Use of the information described herein for other purposes and/or reproduction or copying without the express permission of Seiko Instruments Inc. is strictly prohibited. The products described herein cannot be used as part of any device or equipment affecting the human body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus installed in airplanes and other vehicles, without prior written permission of Seiko Instruments Inc. Although Seiko Instruments Inc. exerts the greatest possible effort to ensure high quality and reliability, the failure or malfunction of semiconductor products may occur. The user of these products should therefore give thorough consideration to safety design, including redundancy, fire-prevention measures, and malfunction prevention, to prevent any accidents, fires, or community damage that may ensue.