Cove cutting on the table saw For cutting just the occasional cove, feeding a piece of wood over the saw blade at an angle is really the ideal way to go. Sure, it takes many passes, but it offers a lot of flexibility and a minimum of set up. So after I wrote my cove cutting table calculator, I figured I might as well write a companion article about cutting coves on the table saw. Cutting a cove on the table saw is a simple matter of feeding the work piece over the blade at an angle. However, the saw blade is really not designed for this kind of cut, as it only has teeth at the edges. So you can really only cut about 2 mm of depth with each pass. A multitude of passes is needed to cut coves of any significant depth. The trick with getting coves right is to get the fence in the right position. This can be a matter of trial and error, although my cove cutting calculator helps. It generates a lookup table for various coves, so you don't need to go back and forth between your computer and your workshop. It helps to clamp your angled temporary fence to the table saw's main fence. This leaves the flexibility of being able to move the fence parallel, to adjust the 1 of 5 08/22/2016 11:32 PM
cove's lateral position without changing its overall geometry. Rather than generating an angle, the cove cutting table calculates the distance from the fence that the temporary fence should have at the near side for smaller angles up to 30 degrees. That way, there's no need to mess with a protractor. Handibot CNC router for cutting wood, plastic, aluminum, HDPE and many other materials. On cutting the cove, its important to securely push the work piece against the fence. Commercial cove jigs have a fence on either side. I'm not sure this is a good idea, as it means the fence will either have play, which results in messy coves, or be too tight, and make it hard to push the piece through. Whatever your do, its best to have the fence angled so that the blade pushes 2 of 5 08/22/2016 11:32 PM
the work piece towards the fence. Although if you feed the work piece too fast, the angle of the blade relative to the work piece will push it away from the work piece. Attaching the temporary cove cutting fence to the main table saw fence is only practical to about 30 degrees. After that, it gets a bit awkward. But at 30 degrees and beyond, most miter gauges can be used, as these will usually go up to 90 degrees from a right angle, which is 30 degrees from the rip fence. Then its just a matter of 3 of 5 08/22/2016 11:32 PM
sliding forwards and back. note the clamp at left. securing the miter gauge to keep it from My cove cutting calculator outputs angles in degrees for angles larger than 30 degrees for this reason. Here's a relatively small cove cut on the table saw. Note the hands for scale. You can see its a fairly smooth cut, though not as smooth as a planed surface. Still, quite satisfactory. And here's a narrow cove cut on the table saw. Note the double bottom of the cove. This cove is only 17 mm wide, but 14 mm deep. The fence was only at about a 5 degree angle. The double peak is because the saw blade doesn't cut as deep in the middle as it does on the edges because the way the teeth are angled. for coves this narrow, its probably better to use a 7 1/4" circular saw blade instead. With a 7 1/4" saw blade, a fence angle of 20 Handibot CNC Router Bits A wide selection of bits & kits for cutting wood, plastic and other surfaces. degrees would be used for those dimensions, and the double bottom would be eliminated. 4 of 5 08/22/2016 11:32 PM
the double bottom wouldn't be visible, so it wouldn't matter. Although really, I'd primarily use a cove that narrow for drawer handles, at which point See also: Improvements to the cove cutting method Making a large picture frame Making a pirate sword out of wood Asymetric cove cutting Making molding with small router bits Molding tricks with a tilting router lift Cove cutting table calculator Tilting router lift Trammel points compass To my Woodworking website 5 of 5 08/22/2016 11:32 PM