Eo2 TM Ethernet over 2-wire Transceiver with PoE+ Model NV-EC1701U Data Sheet Application Example: 6 Watt IP Camera Door Access or other IP device Cat5 100m ( 328ft) NV-EC1701U Model NV-EC1701 Ethernet over Coax Transceiver www.nvt.com (+1) 650.462.8100 (+44) (0) 208 977 6614 2-wire Cable NV-EC1701U Model NV-EC1701 Ethernet over Coax Transceiver www.nvt.com (+1) 650.462.8100 (+44) (0) 208 977 6614 Cat5 100m ( 328ft) Ethernet Switch LAN/ WAN 56 VDC Power Supply Features: 100 BaseT transmission; Network speeds up to 93 Mbps*; Up to 1,000ft (305m)* One NV-EC1701U transceiver at the network-end can support multiple* remote transceivers/ip cameras 56 VDC is distributed over the coax to all connected equipment. Powers PoE, PoE+, or High Power PoE cameras (or other PoE devices), up to 50 watts* Easy configuration, no PC required Transparently supports all networking protocols (UDP, TCP/IP, HTTP, Multicast*, etc.) 128-bit AES encrypted transmission Built-in transient protection; Industrial temperature range Available in 1-4 Camera System Kits Limited lifetime warranty The NVT Model NV-EC1701U Ethernet over 2-wire Transceiver is a compact media converter that allows 10/100 BaseT Ethernet and PoE+ power to be transmitted using ordinary 2-wire cable. These devices are often used in legacy installations where existing cable is re-deployed as part of an upgrade to IP cameras. 56 VDC class 2 power is delivered to one transceiver, which distributes it to multiple* remote transmitters, and their PoE, PoE+, or High Power PoE cameras*. These transceivers are extremely simple to use, with no IP or MAC addressing required. Status LEDs indicate power and link connectivity/activity for each port. They are backed by NVT s award winning customer support and limited lifetime warranty. * Distance and number of devices supported may be lower due to power supply capacity and wire voltage-drop. See Wire Distance Charts on pages 5 & 6. Bandwidth is dynamically allocated. Multicast requires an IGMP Querier within your network switch. High bandwidth streaming devices (>15Mbps) that employ unusually chatty protocols (TCP/IP, TFTP, etc.) are not recommended. Use RTP/UDP instead. Page 1 of 6
TECHNICAL SPECIFICATIONS R J 4 5 E T H E R N E T I N T E R FA C E Connectivity: RJ45, auto-crossover Wire type: Cat5 or better Distance: up to 328ft (100m) Speed: 10/100 Base T, half/full duplex, auto-negotiation auto MDI/MDIX cross-over Latency: 3mS Data throughput: 85Mbps ±10% useable bandwidth per network Example: Four megapixel cameras, all sharing one coax network, each sending 20Mbps video stream(s). Power Output: This Power Sourcing Equipment (PSE) supports Powered Devices (PDs) that are compatible with IEEE 802.3af/at, or PDs that draw up to 50 watts*. For maximum power/distance, 56 VDC appears on all eight RJ45 pins, and are current-protected and transient-protected. 2 - W I R E B U I L D I N G W I R I N G I N T E R FA C E E Connectivity: Screw terminals using the NV-BNCA adaptor Impedance: 25 to 100Ω Distance: See pages 5 & 6 Topology: Bus architecture supports star, daisy-chain, or any combination. One control-room NV-EC1701U may support multiple remote NV-EC1701Us. Transmission technology: IEEE 1901, 128-bit AES encryption * I M P O R TA N T N O T E : Distance will often be shorter due to power supply capacity and wire voltage-drop. See Maximum Per-Camera Wire Distance Chart on page 5. WARNING: For safety, never use more than two power supplies. Never exceed 120 watts. L E D S TAT U S I N D I C AT O R S Power: BNC/2-wire interface: RJ45 Interface: Blue Power On Green Link Green Link P O W E R C O N S U M P T I O N Consumption per transceiver: 3.0 W @ 10 to 56 VDC Generated heat: 10 BTU/hour Total system consumption: = total consumption of transceivers + total consumption of PDs (IP cameras) + total power dissipated in the wire L E D S TAT U S I N D I C AT O R S Power Flashes when initializing or Joining M E C H A N I C A L / E N V I R O N M E N TA L Transceiver body dimensions: 5.1 in (131mm) long x 1.3 in (33mm) high x 1.5 in (38mm) wide (excluding connectors and NV-BNCA adaptor) Transceiver weight: 0.32lb. (145g) Operating and storage temperature: 40 F to 185 F (-40 C to +85 C) 20 to 85% RH non-condensing Transient Immunity: 5x20µS 3000A, 6000V ESD 20KV, 200pF P O W E R S U P P LY Power supplies are external inline, with an IEC380-C14 power inlet and a 6 ft (1.18 m) line cord. Input voltage + 56VDC is 100~240VAC 50/60Hz. A molded P1J 5.5mm barrel connector provides a class 2 (SELV) regulated output with one of these ratings: Model NV-PS56-60W 56V 60W 4.90 in (125 mm) long x 2.00 in (50 mm) wide x 1.25 in (32 mm) high 0.67 lb (0.30 Kg) shipping weight Model NV-PS56-90W 56V 90W 5.77 in (147 mm) long x 2.86 in (60 mm) wide x 1.27 in (32 mm) high 0.94 lb (0.43 Kg) shipping weight Operating / storage temperature: -40 F to +185 F (-40 C to +85 C 20 to 5% relative humidity non-condensing) Transient immunity: 5 x 20µS 3,000A, 6,000V ESD 20KV, 200pF Use only the power cord provided with the unit or equivalent UL approved type SPT-2, SVT, or SJT 18/3 AWG 100~240 VAC, 1 Amp 60 C max 15 ft (4.5 m) long. One end with IEC380-C13 appliance coupler and the other end with NEMA 1015P or equivalent for your country. R E G U L AT O R Y 56VDC Power RoHS BNC RJ45 PoE BNC On when Link detected Flashes with Data RJ45 On when connected Flashes with Data UL Listed to IEC/UL 60950-1 Complies with FCC part 15A limits W A R R A N T Y Limited Lifetime Specifications subject to change without notice. Page 2 of 6
NV-EC1701U ACCESSORIES NV-PS56-60W: 56VDC power supply, 60 watts NV-PS56-90W: 56VDC power supply, 90 watts NV-BNCA: BNC Screw terminal adaptor NV-PC4PR: RJ45 Patch Cord, 4-pair 3 (1m) Grey NV-DPSC4: Detachable Power Supply Cord Splitter 1:4 2ft NV-RMEC16U Rack mounting chassis, 19 x 1U Holds up to 4 NV-EC1701U transceivers plus 60W or 90W power supplies. Includes NV-DPSC4 Power Cord Splitter (Transceivers and power supplies not included) Page 3 of 6
NV-EC1701U TRANSCEIVER KITS Single 60 Watt Eo2 Transmission System NV-EC1701U-KIT1: 2 NV-EC1701U Transceivers 2 NV-PC4PR patch-cord Single 90 Watt Eo2 Transmission System NV-EC1701U-K1H: 2 NV-EC1701U Transceivers 1 1 NV-PS56-90W Power Supply 2 NV-PC4PR patch-cord Dual 60 Watt Eo2 Transmission System NV-EC1701U-KIT2: 3 NV-EC1701U Transceivers 3 NV-PC4PR patch-cord Dual 90 Watt Eo2 Transmission System NV-EC1701U-K2H: 3 NV-EC1701U Transceivers 1 NV-PS56-90W Power Supply 3 NV-PC4PR patch-cord Triple 60 Watt Eo2 Transmission System NV-EC1701U-KIT3: 4 NV-EC1701U Transceivers 4 NV-PC4PR patch-cord Triple 90 Watt Eo2 Transmission System NV-EC1701U-K3H: 4 NV-EC1701U Transceivers 1 NV-PS56-90W Power Supply 4 NV-PC4PR patch-cord Quadruple 60 Watt Eo2 Transmission System NV-EC1701U-KIT4: 5 NV-EC1701U Transceivers 5 NV-PC4PR patch-cord Quadruple 90 Watt Eo2 Transmission System NV-EC1701U-K4H: 5 NV-EC1701U Transceivers 1 NV-PS56-90W Power Supply 5 NV-PC4PR patch-cord Page 4 of 6
NV-EC1701U POWER DISTANCE CHART The distance capability of wire is dependant on its ability to deliver DC power, and separately, to deliver high-frequency data signals. The graph below shows maximum power delivery when using a 56V power supply. If you are locally powering your camera (or other remote device), then this graph does not apply. The graph on the next page shows the maximum data delivery rate. A Distance Calculator can be found at www.nvt.com. PoE devices require a minimum of 43V to operate. With a 56V supply, we have up to 13V of allowable voltage drop on the wire. The voltage will dip in proportion to the remote (camera) load. The graph below shows what PoE power distances are supported for various loads and wire types. Start with the camera wattage at the left. Sometimes IP cameras are listed as to their PoE Class rather than wattage. Now read over to the right until you find your kind of wire. Then look up (feet) or down (meters) to find your maximum distance. If your wire is not among the examples, simply measure its total resistance and find the value on the right side of the graph. The maximum supported wattage is on the left. NV-EC1701U Power Distance Camera Wattage 50 W 40 W 30 W 25 W 20 W 18 W 15 W 12 W 10 W 8.0 W 6.0 W 5.0 W 4.0 W 3.0 W 2.5 W 2.0 W 98 ft 197 ft 164 ft 131 ft High Powe wer PoE Class 4 PoE Class 1 262 ft 984 ft 820 ft 656 ft 590 ft 492 ft 397 ft 328 ft 5 RG59/U 22 AWG RG59/U 23 AWG CATV 20 AWG 2-Wire 24 AWG 2-Wire 2-Wire 22 AWG 4-pair Cat5 or 2-Wire 18 AWG 20 AWG TV 2 1,312 ft C ATV 22 AWG 1,968 ft 1,640 ft 2,624 ft RG59/U 20 AWG RG6 6,560 ft 5,904 ft 4,920 ft 3,936 ft 3,280 ft 18 AWG AW RG11 9,840 ft 8,200 ft 14 AWG AW 13,120 ft 19,680 ft 16,400 ft 26,240 ft 32,800 ft 3 Ω 4 Ω 6 Ω 7 Ω 9 Ω 11 Ω 12 Ω 14 Ω 16 Ω 19 Ω 21 Ω 23 Ω 24 Ω 28 Ω Total Wire Resistance 0 W 38 Ω 30 m 60 m 50 m 40 m 80 m 300 m 250 m 200 m 180 m 150 m 120 m 100 m 400 m 600 m 500 m 800 m 2,000 m 1,800 m 1,500 m 1,200 m 1,000 m NV-EC1701U Power Distance 3,000 m 2,500 m 4,000 m 6,000 m 5,000 m 8,000 m 10,000 m Page 5 of 6
NV-EC1701U WIRE DISTANCE CHART Wire Type and Data Distance Capacity There are a wide variety of wire qualities. The graph below will help you determine your data throughput as a function of wire type and distance. A Distance Calculator can be found at www.nvt.com. NV-EC1701U Wire Distance 1000 ft 820 ft 656 ft 492 ft 328 ft 262 ft 197 ft 164 ft 131 ft 98 ft 66 ft 49 ft 33 ft 100 Mbps Ethernet Aggregate Data Throughput 90 Mbps 80 Mbps 70 Mbps 60 Mbps 50 Mbps 40 Mbps 30 Mbps 20 Mbps 10 Mbps 0 Mbps Shielded Sh e ded 18/2 18/2 Cat5 300 m 250 m 200 m 150 m 100 m 80 m 60 m 50 m 40 m 30 m 20 m 15 m 10 m NV-EC1701U Wire Distance Page 6 of 6 Copyright 2014 NVT, Inc. 411-2137-1-E2