Instruction Sheet VDM Series FIXED & TILT WALL MOUNT VDM-800-F VDM-800-T THANK YOU Thank you for purchasing the Vision Display fixed and tilt wall mounts. Please read these instructions thoroughly before installing or assembling these products. PRODUCT FEATURES Open wall plate design maximizes accessibility to connections and cable pass-through behind the display Post-install leveling mechanism enables quick micro-adjustment of horizontal plane of display Safety locking features keep the display securely mounted VESA Capability: VDM-800-F 75x75mm - 800x600mm VDM-800-T 75x75mm - 800x600mm I-00809 Rev A
IMPORTANT SAFETY INSTRUCTIONS / INSTRUCTIONS IMPORTAANTES SUR LA SÉCURITÉ SAVE ALL INSTRUCTIONS / CONSERVER CES INSTRUCTIONS WARNING/AVERTISSEMENT and the exclamation point within an equilateral triangle is intended to alert the user to the possibility of serious injury or death if the instructions are not followed. Avertissement et le point d'exclamation dans un triangle équilatéral est destiné à alerter l'utilisateur de la possibilité de blessures graves ou la mort si les instructions ne sont pas suivies. CAUTION/ATTENTION and the exclamation point within an equilateral triangle is intended to alert the user to the possibility of damaging or destroying the equipment if the instructions are not followed. Attention et le point d'exclamation dans un triangle équilatéral est destiné à alerter l'utilisateur de la possibilité d'endommager ou de détruire l'équipement si les instructions ne sont pas suivies. WARNING: Failure to read, understand and follow the following information can result in serious personal injury, damage to the equipment or voiding of the warranty. AVERTISSEMENT: Ne pas lire, comprendre et suivre les informations suivantes peut entraîner des blessures graves, des dommages à l'équipement ou de la nullité de la garantie. WARNING: Failure to provide correct structural strength for the component may result in serious personal injury or damage the equipment. The 2x4 stud wall to which the component is being attached may have a maximum drywall thickness of 5/8 (1.6 cm). AVERTISSEMENT: Le défaut de fournir une résistance structurelle correcte pour le composant peut entraîner des blessures graves ou endommager l'équipement. Le goujon de 2x4 auquel le composant mur est connecté peut avoir un maximum de 1.6 cm (5/8 ) d'épaisseur cloison sèche. WARNING: Exceeding the weight capacity may result in personal injury or equipment damage. The combined weight of all components attached to the mount must not exceed weights listed on page 3. AVERTISSEMENT: Dépasser la capacité de poids peut entraîner des blessures ou des dommages matériels. Le poids combiné de tous les composants reliés au support de montage ne doit pas dépasser les grammages indiqués à la page 3. WARNING: Be aware of pinch points and do not place fingers in between moving parts. AVERTISSEMENT: Soyez conscient des points de pincement et de ne pas placer les doigts entre les pièces mobiles. WARNING: Use this product for its intended use and only use attachments recommended by the manufacturer. AVERTISSEMENT: Utilisez ce produit pour son utilisation prévue et utiliser uniquement les accessoires recommandés par le fabricant. WARNING: Do not use a damaged product. Return damaged products to a qualified service center for repair. AVERTISSEMENT: Ne pas utiliser un produit endommagé. Retour produits endommagés à un centre de service qualifié pour la réparation. WARNING: Not intended for outdoor use. AVERTISSEMENT: Non destiné à une utilisation en extérieur. Page 2
WEIGHT RATINGS Model VDM-800-F VDM-800-T Weight Rating 200 lbs. Maximum Total Rated Load 200 lbs. Maximum Total Rated Load TOOLS REQUIRED #2 Phillips Screwdriver Drill Protective Eyewear 7/32 Wood Bit or 7/16 Masonary Bit Level Hammer 1/2 Hex Socket WARNING: Use tools with caution and follow all necessary safety protocols. AVERTISSEMENT: Utiliser des outils avec prudence et suivre tous les protocoles de sécurité nécessaires. SUPPLIED COMPONENTS (2) Extension Brackets VDM-800-F (B1) (1) Wall Mount Bracket (A) (2) Fixed Display Mount Brackets VDM-800-F (B) Page 3 (2) Extension Brackets VDM-800-T (C1) (2) Tilt Display Mount Brackets VDM-800-T (C)
COMPONENTS SUPPLIED (CONTINUED) (8) Extension Screws (F) (6) Wall Anchor (E) (6) Hex Head Screw (D) M5 Washer (H) (14) M8 Washer (G) Display Mount Spacers M6 Short Spacer (J) M6 Long Spacer (K) M8 Short Spacer (L) M8 Long Spacer (M) Display Mount Screws M4 x 12 M4 x 16 M4 x 20 (N-B) (N-C) (N-A) M5 x 12 M5 x 16 M5 x 20 M5 x 30 (N-E) (N-D) (N-G) (N-F) (1) Proximity Mounting Plate Kit (P) M6 x 12 (N-H) M6 x 20 (N-J) M6 x 30 (N-K) M8 x 16 (N-L) M8 x 20 (N-M) Page 4 M8 x 40 (N-N)
WOOD STUD WALL BRACKET INSTALLATION 1. Determine height for display and find center of stud closest to desired position on wall. Locate the center of the stud to the left and right of desired location. 2. Using a level, scribe a 10 long line down the center of all 3 studs at the desired height. (FIGURE A) FIGURE A 3. Using a level and the wall mount bracket (A) as a template, mark the center of the 6 mounting holes in line with the scribed center line of each stud. (FIGURE B) Mounting holes A FIGURE B 4. Remove wall mount bracket and using a 7/32 drill bit, drill a 2.5 deep pilot hole in each of the 6 marked center points. Page 5
WOOD STUD WALL BRACKET INSTALLATION CONT. 1) Install wall mounting bracket (A) using (6x) hex head screw (D) and (6x) 8M washers (G). (FIGURE C) D G A FIGURE C BLOCK OR CEMENT WALL BRACKET INSTALLATION 1. Determine position and height for display. Using a level and the wall mount bracket (A) as a template, mark the center of the 6 mounting slots that are spaced the farthest apart. (FIGURE D) Mounting holes A FIGURE D Page 6
BLOCK OR CEMENT WALL BRACKET INSTALLATION CONT. 2. Remove wall mount bracket and using a 7/16 drill bit, drill a 2.5 deep hole in each of the 6 marked center points. (FIGURE E) 3. Press a wall anchor (E) into each of the 6 drilled holes (Wall Anchors may require a hammer to install). (FIGURE E) NOTE: Wall anchors may require a hammer to install. E FIGURE E 4. Install wall mounting bracket (A) using (6x) hex head screws (D) and (6x) M8 washers (G). (FIGURE F) NOTE: To prevent anchors from stripping, only use a hand tool to install. D G A FIGURE F Page 7
STOP These display mounts are supplied with a Proximity Series Mounting Plate PRX-MP-9X12. Before installing display mounting brackets to your display, follow the supplied mounting plate installation instructions I-00804 to find the best location for mounting your plate. Page 8
DISPLAY MOUNT BRACKET EXTENSION INSTALLATION FIXED MOUNT VDM-800-F 1. For larger displays, it may be necessary to attach extension bracket (B1) to align display mounting bracket (B) mounting holes with VESA holes in display. B1 F B TILT MOUNT VDM-800-T 1. For larger displays, it may be necessary to attach extension (C1) to align display mounting bracket (C) mounting holes with VESA holes in display using (8x) extension screws (F). Both extension brackets can be attached to the top or bottom of display mounting brackets. NOTE: Adding to top of brackets will raise the display slightly on the wall mount bracket. Attaching to the bottom will lower the display slightly on the wall mount bracket. (FIGURE G) C1 Top of brackets F C FIGURE G Page 9 Bottom of brackets
FLUSH DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied display mount screws,select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw. If supplied screws are still too long, use supplied spacers to take up slack. 2. Align display mount bracket (B or C) with mounting holes on the back of display. Using (4x) display mount screws (N-A - N-N) and (4x) washers (G or H) to secure the display mount brackets to your display. (FIGURE H) TV TV TV TV B or C N-A - N-N C G or H B FIGURE H Page 10
RECESSED OR RAISED BACK DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied display mount screws,select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw. If supplied screws are still too long, use supplied spacers to take up slack. 2. Align display mount bracket (B or C) with mounting holes on the back of display. Using (4x) display mount screws (N-H - N-N), (4x) washers (G or H) and (4x) spacers (J - M) to secure the display mount brackets to your display. (FIGURE J) TV TV TV TV B or C J-M N-A - N-N C G or H B FIGURE J Page 11
HANGING DISPLAY (FIXED MOUNT) 1. Tilt display and hook display bracket onto flange of wall mount bracket (A). Standoff support may be used to prevent display from locking into place while connecting wires. (FIGURE K) 2. Swing standoff supports up to lower display in place. Push along the bottom of display until the mount clicks into place. (FIGURE L) 3. To remove display from the wall bracket, pull both release cord rings down while pulling bottom of display away from wall and lift display off flange of wall mount bracket. (FIGURE M) FIGURE K FIGURE L FIGURE M Standoff Support Release Cord 4. Once installation is complete, use level adjustment screws on top of display mount brackets to level display. After display is level, screw in both display lock screws on bottom of brackets to secure display to wall mount. (FIGURE N) Leveling Screws FIGURE N Display Lock Screws Page 12
HANGING DISPLAY (TILT MOUNT) 1. Tilt display and hook onto flange of wall mount bracket. (FIGURE P) 2. Push along the bottom of display until the mount clicks into place. (FIGURE R) 3. To remove display from the wall mount bracket, pull both release cord rings down while pulling bottom of display away from wall. Lift display off flange of wall mount bracket. (FIGURE S) FIGURE P FIGURE R FIGURE S Release Cord 4. Once installation is complete, use level adjustment screws on top of display mount brackets to level display. After display is level, screw in both display lock screws on bottom of brackets to secure display to wall mount. (FIGURE T) Leveling Screws FIGURE T Display Lock Screws Page 13
ADJUSTING DISPLAY TILT (VDM-800-T ONLY) 1. To tilt display, loosen wing screws on both display brackets. 2. Grab top and bottom of display and gently pull top of display to desired angle. Tighen both wing screws to lock display at desired angle. 3. To return display to a vertical position, loosen both wing screws and grab top and bottom of display, carefully push display from the top. Tighten wing screws to lock in position. NOTE: Wing screw is spring loaded to allow you the ability to reposition wing when loosening and tightening mount. To reposition, pull wing out and reposition. +15 /-5 Wing Screw Page 14
THIS PAGE INTENTIONALLY LEFT BLANK. Page 15
WARRANTY For warranty information, refer to www.middleatlantic.com/terms. Corporate Headquarters Corporate Voice: 973-839-1011 - Fax: 973-839-1976 / International Voice: +1 973-839-8821 Fax: +1 973-839-4982 www.middleatlantic.com - info@middleatlantic.com Middle Atlantic Canada Voice: 613-836-2501 - Fax: 613-836-2690 ca.middleatlantic.com - customerservicecanada@middleatlantic.ca Factory Distribution USA: NJ - CA - IL Canada: ON - BC At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company. Page 16