Napa 4 in1 Crib Assembly Instruction Important Information: Read all instructions BEFORE assembling crib. KEEP INSTRUTIONS FOR FUTURE USE. Page 1
CRIB WARNINGS! WARNING - R ruc bef r r b. KEEP INSTRUCTIONS FOR FUTURE USE. DO NOT USE R L L WED.!! WARNING- WARNING- WARNING: T reduce he k f SIDS pe re e d he hy f p aced he r back eep, u e herw e adv ed by ur p a. ef re each u a e r a e b y, pec cr b f r da a ed hardware, e, par r harp ed e. DO NOT u e cr b a y par are r br ke. A k y ur dea er r wr e &T I e a /S re e f r rep ace e par a d ruc a era ure f eeded. ub u e par. DO NOT wa a r r b. NEVER a r c v bec e f ca I r, p f re r duc. Failure to follow these warnings and assembly instructions could result in serious injury or death. Infants can suffocate on soft bedding. Never add a pillow or comforter Never place additional padding under an infant. Infants can suffocate in gaps between crib sides and a mattress that is too small. ENTRAPMENT/ STRANGULATION HAZARD r b Follow warnings on all products in a crib S r c r a DO NOT c r r d, h r c rd. DO NOT p r v r a r y. DO NOT c r r c r r rap a r d. a w. DO NOT c c rd, r a c bec w r d r b. Whe d ab e pu a p e ress we p a d re bu per pad, ar y a d her bjec a d erve a ep f r b u. W r h., r b c b c ver r bed. ar FALL HAZARD CAUTION : ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4 (69CM) x 51 5/8 (131 CM) WITH A THICKNESS NOT EXCEEDING 6 (15CM). r f r f y b k r r y, a ever c p r per r c bef r y r b. Mak r a b h Page 2
Parts list No. Qty. Description A 1 Headboard B 1 Footboard C 1 Left side D 1 Right side E 2 Stabilizer bars F 1 Mattress with support Brackets G 1 136# Guardrail ( Not included, sold separately) H 2 215# Bed Rails ( Not included, sold separately) A D E B C F G H a. General Allen head bolt M6 X 70mm ( 4 pcs) e. Philips Screw M5 X 32mm ( 8 pcs) f. Barrel Nut ( 8 pcs) b. General Allen head bolt M6 X 55mm ( 6 pcs) g. Flat Washer ( 20 pcs) h. Lock Washer ( 28 pcs) c. General Allen head bolt M6 X 35mm ( 6 pcs) i. Wing Nuts ( 8 pcs) k. Allen Wrench ( 1 pc ) d. General Allen head bolt M6 X 102mm ( 4 pcs) Important: In order to properly assemble the crib, carry out the operations in order specified. Failure to assemble the crib in the manner recommended order can make the crib hazardous. Page 3
Right side ( D ) Left side ( C ) Barrel Nut ( f ) Barrel Nut ( f ) Allen Wrench ( k ) Allen Head Bolts ( a ) Allen Head Bolts ( d ) Flat Washer A. Attach the stabilizer bars to both the left and right sides (C&D) as shown. B. Start by inserting the Barrel Nuts ( f ) into the predrilled holes in the stabilizer bars. Refer to figure 1 to make sure the threaded hole in th center of the Barrel Nut is properly aligned to capture the Allen head bolt ( a&d ). NOTE: Make sure that the Barrel Nut is inserted with slotted end facing out. C. To attach the stabilizer bar on the crib sides, insert the Allen head bolts ( a&b ) Flat Washer through the lock washers and flat washers, then through the pre-drilled holes on the crib sides, and finally into the holes in the end of the stabilizer bars to join with the barrel nut. Tighten with the Allen Wrench ( k ). Figure 1A. Repeat on the 3 remaining corners. Barrel Nut ( f ) Allen Head Bolts ( a ) Allen Head Bolts ( d ) page 4
Noted : You will need a cross-point screwdriver. (not included) Right side ( D ) Left side ( C ) Phillips Screw ( e ) Wing Nut ( i ) Lock Washer Phillips Screw ( e ) Phillips Screw ( e ) page 5
205 #Napa 4 in 1 crib assembly instructions ( JW ) ( b ) Headboard ( A ) ( b ) ( b ) Allen Head Bolts ( b ) Flat Washer Flat ( c ) Allen Head Bolts ( c) Flat Washer page 6
TODDLER BED and FULL SIZE BED ASSEMBLY ( Option Purchase ) Note: The Toddler rail (#136) and Adult rail (#215) are sold separately to convert the crib to a Toddler bed and a full size bed for your choose. Contact the store where you purchased the crib or visit www.sorellefurniture.com to locate a dealer near you. Disassembling Crib for Storage To disassemble crib for storage, follow assembly steps in reverse. Store all parts and hardware together in a safe place. Store the instruction manual in the supplied envelope attached to mattress support base for future reference for reassembly. Cleaning and Storage To clean, use only mild household soap and warm water. DO NOT use bleach or detergent. DO NOT use abrasive cleaners which can scratch the finish. Use clean soft cloths to wash, rinse and dry. With proper care, the quality finish will last a long time. Wood surfaces may be treated with a light application of a good grade of non-toxic furniture polish. Read contents on back of polish to make sure polish will not harm unit. Store all parts from Crib, which are not used for Full Size Headboard, in original carton(s) (if available) to prevent damage and allow reuse. page 7