TS39/A/B/C UNISONIC TECHNOLOGIES CO., LTD LOW POWER SINGLE VOLTAGE COMPARATOR DESCRIPTION The UTC TS39/A/B/C consists of a low power voltage comparator designed specifically to operate from a single supply over a wide range of voltages. Operation from split power supplies is also possible. This comparator also has a unique characteristic in that the input common-mode voltage range includes ground even though operated from a single power supply voltage. FEATURES * Wide single supply voltage range or dual supplies +2V~+36V or ±V~±8V * Very low supply current (.2mA) independent of supply voltage (mw /comparator at +V) * Low input bias current: 2nA typ. * Low input offset current: ±na typ. * Low input offset voltage: ±mv typ * Input common-mode voltage range includes ground. * Low output saturation voltage: 2mV typ.(i OUT =ma). * Differential input voltage range equal to the supply voltage. * TTL, DTL, ECL, CMOS Compatible outputs. ORDERING INFORMATION Ordering Number Package Packing TS39G-AF-R SOT-2 Tape Reel TS39AG-AF-R SOT-2 Tape Reel TS39BG-AF-R SOT-2 Tape Reel TS39CG-AF-R SOT-2 Tape Reel TS39G-AL-R SOT-33 Tape Reel TS39AG-AL-R SOT-33 Tape Reel TS39BG-AL-R SOT-33 Tape Reel TS39CG-AL-R SOT-33 Tape Reel of 6 Copyright 2 Unisonic Technologies Co., Ltd
TS39/A/B/C MARKING TS39 TS39A TS39B TS39C PIN CONNECTIONS (top view) Vcc TS39 Vcc TS39A - + Vcc 2 3 IN(-) TS39B IN(-) 2 3 IN(-) TS39C + - 2 3 UNISONIC TECHNOLOGIES CO., LTD 2 of 6
TS39/A/B/C BLOCK DIAGRAM V CC + 3.μA μa 3.μA μa IN(-) UNISONIC TECHNOLOGIES CO., LTD 3 of 6
TS39/A/B/C ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATING UNIT Supply Voltage V CC ±8 or 36 V Differential Input Voltage V I(DIFF) ±36 V Input Voltage V IN -.3 ~ +36 V Short-Circuit to Ground (Note 2) Infinite Power Dissipation P D mw Junction Temperature T J C Operating Temperature T OPR - ~ +2 C Storage Temperature T STG -6 ~ + C Notes:. Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. 2. Short-circuit from the output to V CC can cause excessive heating and eventual destruction. The maximum output current is approximately 2mA, independent of the magnitude of V CC. THARMAL DATA (T J = C, T A =2 C) PARAMETER SYMBOL RATING UNIT Junction to Ambient θ JA 2 C/W ELECTRICAL CHARACTERISTICS (V CC =.V, All voltage referenced to, T A =2 C, unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Input Offset Voltage (Note ) V I(OFF) T A =+2 C mv T MIN T A T MAX 9 mv Differential Input Voltage (Note ) V I(DIFF) V CC V Large Signal Voltage Gain G V V CC =V, R L =k, V OUT =~ V 2 V/mV Input Common Mode Voltage T A =+2 С V CC -. V V I(CM) Range (Note 3) T MIN T A T MAX V CC -2 V Low Level Voltage V OL V I(DIFF) =V, T A =+2 C 2 mv V CC = V OUT =3V T MIN T A T MAX 7 mv Input Bias Current (Note 2) I I(BIAS) T A =+2 С 2 2 na T MIN T A T MAX na Input Offset Current I I(OFF) T A =+2 С na T MIN T A T MAX na Supply Current I CC V CC =V, no load.2. ma V CC =3V, no load..2 ma sink current I SINK V I(DIFF) =-V, V OUT =.V 6 6 ma High Level Current I OH V I(DIFF) =V, T A =+2 C. na V CC = V OUT =3V T MIN T A T MAX μa Response Time t R R L =.kω to V CC (Note ).3 μs Large Signal Response Time t REL V IN =TTL,V REF =+.V,R L =.KΩ~ V CC 3 ns Notes:. At output switch point, Vo=.V, R S =Ω with V CC from V ~ 3V and over the full input common-mode range (V ~ V CC.V). 2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output, so no loading charge exists on the reference or input lines. 3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than.3v.the upper end of the common-mode voltage range is V CC + -.V,but either or both inputs can go to +3V without damage.. Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range the comparator will provide a proper output state. The low input voltage state must not be less than -.3V (or.3v below the negative power supply, if used).. The response time specified is for a mv input step with mv overdrive. For larger overdrive signals 3ns can be obtained. UNISONIC TECHNOLOGIES CO., LTD of 6
Saturation Voltage (V) Input Current (na) Supply Current (ma) TS39/A/B/C TYPICAL CHARACTERISTICS...3.2. Supply Current vs. Supply Voltage T A =- С T A =+2 С T A =+2 С R= 2 3 Supply Voltage (V) Input Voltage (mv) Voltage (V) 6 3 2 - - Response Time for vs. Input Overdrives - Negative Transition 2mV mv Input overdrive:mv.. 2 Time (µs) ei +V - + T A =+2 С.kΩ eo 8 6 2 Input Current vs. Supply Voltage T A =- С T A =+2 С T A =+2 С 2 3 Supply Voltage (V) Input Voltage (mv) Voltage (V) 6 3 2 Response Time for vs. Input Overdrives - Positive Transition Input overdrive:mv T A =+2 С 2mV.. 2 Time (µs) mv ei +V - +.kω eo Saturation Voltage vs. Current Out of saturation T A =+2 С - T A =- С -2 T A =+2 С -3-2 - 2 Sink Current (ma) UNISONIC TECHNOLOGIES CO., LTD of 6
TS39/A/B/C UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD 6 of 6