Mia Workdesk Assembly Instructions - Please keep for future reference White 190 Dimensions Width : 1.5 cm Depth : 55.0 cm Height: 7.0 cm Assembly Instructions - Please keep for future reference If you need help or have damaged or missing parts, call the Argos Customer Helpline: 05 0 0 0 5071 Issue 1-5-05-01
! Safety and re Advice Important - Please read these instructions fully before starting assembly Check you have all the components and tools listed on pages and. Remove all fittings from the plastic bags and separate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. Do not stand or put weight on the product, this could cause damage. Assemble the item as close to its final position (in the same room) as possible. Assemble on a soft level surface to avoid damaging the unit or your floor. Parts of the assembly will be easier with people. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. Dispose of all packaging carefully and responsibly. re and maintenance Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference. 1
Components - Panels If you have damaged or missing components, call the Argos Customer Helpline: 05 0 0 0 Please check you have all the panels listed below 1 Top (1,5 cm x 55 cm) Side, right (15,5 cm x 5, cm) Side, left (15,5 cm x 5, cm) Divider (1, cm x,1 cm) 5 Leg, right x (7,5 cm x 5,0 cm) Leg, left x (7,5 cm x 5,0 cm) 7 Front rail (111,5 cm x cm) Back rail (111,5 cm x 15,5 cm) Drawer side, right/left (5 cm x 9, cm) x 11 Drawer back x (50, cm x 9, cm) 9 Drawer front x (55, cm x 1,5 cm) 5071-0 1 Drawer bottom x (51, cm x,7 cm)
Components - ttings Please check you have all the panels listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. Ab Bp ø x 0mm Wooden dowel x ø x 0mm Wooden dowel x ø x 5mm Screw x Dj ø15 x.5mm m x ø5 x 11, ccmm Bolt x ø5 x mm Screw x Fh Hk Back fitting w. ø.5 x 15mm Screw x M x 9mm Screw x Wall strap and instruction x 1 ø5. x mm Screw x ø5. x 19mm Screw x ø x 9mm Spacer x 5 x 17 x mm Drawer runner x Tools required Phillips screwdriver (Medium & large) Hammer Flatblade screwdriver (Medium) Ruler - Use this ruler to help correctly identify the screws 0 0 0 0 50 0 70 0 90 0 1 10 10 10 150 10 170 5071-0
Step 1 Assembly of the desk. 1 7 5 5 Step 1.1 Knock the dowels into the holes indicated on the sides and using a small hammer. ø x 0mm Wooden dowel x 1 Step 1. Screw the bolts into the holes indicated on the legs and 5. ø5 x 11, ccmm Bolt x 5 x x Step 1. Place the legs and 5 onto the sides and. Push cams into the holes indicated on the sides and. Arrows pointing towards the legs / 5. 5 ø15 x.5mm m x Turn the cams to the right to fix the legs and 5. 5 5071-05
Step 1. Screw the bolts into the holes indicated on the sides and. ø5 x 11, ccmm Bolt x Step 1.5 Slide the top of the drawer runners backwards. You can identify the front end of the drawer runner by the two M holes. See details. ø x 9mm Spacer x Front end ø5. x 19mm Screw x 5 x 17 x mm Drawer runner x Place the Spacers as shown, and fix the front end of the drawer runners to the sides and using screws through the holes number and as indicated. Hole no. Hole no. See details. Front end Front end Hole no. Hole no. 5 5071-0
Step 1. Slide the top of the drawer runners forwards. ø5. x 19mm Screw x ø x 9mm Spacer x Place the Spacers as shown, and fix the back end of the drawer runners to the sides and using screws through the holes indicated. See details. Step 1.7 Knock the dowels into the holes indicated on the back rail, the front rail 7 and the divider using a small hammer. ø x 0mm Wooden dowel x 7 5071-07
Step 1. Slide the top of the drawer runner backwards. Identify the front end of the drawer runner by the two M holes. x the front end of the drawer runner to the divider using screws through the holes number and as indicated. Step 1.9 Slide the top of the drawer runner forwards. ø5. x mm Screw x Front end 5 x 17 x mm Drawer runner x1 Hole no. Hole no. ø5. x mm Screw x x the back end of the drawer runner to the divider using screw through the hole indicated. Step 1. Turn the divider upside down. ø5. x mm Screw x 5 x 17 x mm Drawer runner x1 Slide the top of the drawer runner forwards. x the front end of the drawer runner to the divider using screws through the holes number and as indicated. Hole no. Hole no. Step 1.11 Slide the top of the drawer runner forwards. x the back end of the drawer runner to the divider using screw through the hole indicated. ø5. x mm Screw x 1 7 5071-0
Step 1.1 Screw the bolts into the holes indicated on the top 1. ø5 x 11, ccmm Bolt x 1 Step 1.1 Place the divider onto the top 1. ø15 x.5mm m x Push cams into the holes indicated on the divider. Arrows pointing towards the top 1. 1 Turn the cams to the right to fix the divider. Step 1.1 Place the sides and onto the back rail and the front rail 7. ø15 x.5mm m x Push cams into the holes indicated on the back rail and the front rail 7. Arrows pointing towards the sides /. Turn the cams to the right to fix the sides and. 7 5071-09
Step 1.15 Place the sides and onto the top 1. ø15 x.5mm m x Push cams into the holes indicated on the sides and. Arrows pointing towards the top 1. Turn the cams to the right to fix the top 1. 1 Step 1.1 x the back rail and the front rail 7 to the divider as shown, using screws Dj. Dj Dj ø5 x mm Screw x 7 Dj Step 1.17 Important!! The work desk is heavy. Lift with care. Its recommended that the work desk is fixed to the wall. Fh Wall strap and instruction x 1 Use the fittings Fh. Follow the instructions included with the fittings. 9 5071-
Step Assembly of the drawers. 11 1 9 x Step.1 x the drawer sides to the drawer back 11 as shown, using screws Bp. 11 Bp ø x 5mm Screw x Bp Bp x Step. Knock the dowels Ab into the holes indicated on the drawer sides using a smal hammer. Ab ø x 0mm Wooden dowel x 1 Ab Ab x Step. Slide the drawer bottom 1 into the drawer sides. 1 x Step. Screw the bolts into the holes indicated on the drawer front 9. ø5 x 11, ccmm Bolt x 9 x 5071-11
Step.5 Push the drawer front 9 onto the drawer sides. Place cams into the holes indicated. Arrow pointing towards the front. Turn the cams to the right to fix the front. 9 ø15 x.5mm m x x Step. Important!! Make sure the angle between the drawer front 9 and the drawer sides is 90 before the drawer bottom 1 is fixed using as shown. To adjust the angle between the sides and the front push the fitting sidewards. Back fitting w. ø.5 x 15mm Screw x 90 x Step.7 Pull out the drawer runners. Slide the drawers onto the runners. Hk M x 9mm Screw x x drawers to the drawer runners using screws Hk. Hk Hk 11 5071-1