740141 - STEEPLE GTE RRIER SET The 740141 Steeple Gate arrier Set consists of four height adjustable barriers; one 5 meter wide beam and three 4 meter wide beams. These barriers can also be used to effectively discourage joggers and recreational runners from using the inside lanes and causing premature and uneven wear. 1 x 5 meter (74014117) 3 x 4 meter (74014114) Spring loaded pull pin & clamping knobs for height adjustment Locking pin for lane gate position (pad lock not included) Track urbing The barrier adjusts to three heights; 30, 33, and 36 inches. The beam is locked in position with a stainless steel spring loaded pull pin and clamping knobs. The beam is constructed of 4 inch square 11 gauge steel tube, covered on three sides with 1/2 inch thick Vultrak track surface. Ground Plate The leg assemblies are fabricated from 2-1/2 " and 3-1/2" Sch 40 steel pipe with spring assist. The legs are painted with powder coat for a durable finish. One leg assembly is mounted to a concrete footing. opyright 2014 by Gill thletics. Page 1 of 5
740141 - STEEPLE GTE RRIER SET 4.20 m 0.51 m 3.69 m Track urbing 30" One leg of the barrier is mounted to a ground plate. The ground plate must be anchored into a concrete footing. Note: these footing dimensions should be considered minimums and local soil conditions must be taken into account. The ground plate must be set so that the top of the ground plate is level with the finished elevation of the running track. It is critical that the ground plates be located correctly. The ground plate should be set to the infield side of the track curbing. Track urbing For each mounting plate, drill four two 7/8" holes 1/4" deep. 7/16" holes 3-1/2" deep and 6" 9" Use acrylic anchoring adhesive (not included) to secure the anchor studs in the holes. 3" 1" 6" 4" Top of Track Surface 7 8 " 7 16 " Top of concrete Track urbing opyright 2014 by Gill thletics. Shallow holes for clearance of the 3/4" bolts Page 2 of 5
740141 - STEEPLE GTE RRIER SET 5/16" Flat Washer (HDWE050020E0) 3/8"-16 x 1" Hex olt (HDWE011240E0) olt the upper legs to the bottom of the beam in four places per leg. Upper Leg (no hole between knobs) (74014020) Slide the spring into the top of the lower leg. Make sure the clamping knobs are backed out. With at least two people, lift the beam and slide the upper leg onto the lower leg. Spring (74014025) Pull the pin out to adjust to the designed height. Tighten the clamping knobs to secure the beam. Free Standing Leg 74014131 opyright 2014 by Gill thletics. Page 3 of 5
740141 - STEEPLE GTE RRIER SET 5/16" Flat Washer (HDWE050020E0) Locking Pin & Tether (7401412007) 3/8"-16 x 1" Hex olt (HDWE011240E0) Upper Leg with hole between knobs (74014120) olt the upper legs to the bottom of the beam in four places per leg. Spring (74014025) olt the lower leg to the mounting plate. Slide the spring into the top of the lower leg. Make sure the clamping knobs are backed out. Ground Mount Leg (74014130) With at least two people, lift the beam and slide the upper legs onto the lower legs. Pull the pin out to adjust to the designed height. Tighten the clamping knobs to secure the beam. 3/4" Flat Washer SS (M2541) 3/4"-10 x 1-1/4" Hex olt SS (M2540) 3/8"-16 Heavy Nylock Hex Nut SS (M2785) 3/8" Flat Washer SS (2534) Stainless Steel Mounting Plate (M1756) opyright 2014 by Gill thletics. DETIL 3/8"-16 x 5" Threaded Stud SS (M2786) Page 4 of 5
740141 - STEEPLE GTE RRIER SET DJUSTING THE HEIGHT 1. Make sure that the tethered lockable pin () is removed. 2. Loosen all four clamping knobs (). 3. Pull out the spring loaded pull pins () and adjust height. Release pull pin. 4. Tighten all four clamping knobs (). SETTING S LNE GTE 1. Raise the barrier to the highest setting (36 inches). 2. Insert the lockable pin () through the hole in the leg (). 3. The pin can be locked in place (pad lock not included). ROTTING TO THE STORGE POSITION 1. Make sure that the tethered lockable pin () is removed. 2. Loosen the two clamping knobs () on the pivot leg. 3. On the pivot leg, pull out the spring loaded pull pin () and rotate it so that it stays in the "out" position. 4. Lift the free standing leg (D) slightly and rotate it off of the track. D THIS WRNING IS GIVEN IN OMPLINE WITH LIFORNI'S PROPOSITION 65: WRNING This product contains chemicals known to the State of alifornia to cause cancer, birth defects or other reproductive harm. opyright 2011 by Gill thletics. suggestions@gillathletics.com Page 5 of 5