SECTION 10 57 23.13 (10670) - WIRE CLOSET AND UTILITY SHELVING PART 1 GENERAL 1.01 SUMMARY 1. Wire Closet Shelves B. Related Sections: 1. Section 06 10 00 (06100) - Rough Carpentry 1.02 QUALITY ASSURANCE A. Installer Qualifications: Manufacturer's authorized representative who is trained and approved for installation of units required for this Project. B. Source Limitations: Obtain metal storage shelving through one source from a single manufacturer. 1.03 DELIVERY, STORAGE, AND HANDLING A. Deliver storage shelving palleted, wrapped, or crated to provide protection during transit and Project-site storage. 1.04 PROJECT CONDITIONS A. Environmental Limitations: Do not deliver or install metal storage shelving until spaces are enclosed and weatherproof, wet work in spaces is completed and dry, and ambient temperature is being maintained at the levels indicated for Project when occupied for its intended use. PART 2 PRODUCTS 2.01 WIRE CLOSET SHELVES A. Approved Manufacturers: 1. Lifetime Ventilated Series Shelf with Hanging Rod ; Organized Living (888-674-5484) B. Components: 1. Structural Performance: a. Structural Performance: Back clips spaced 11 inches with support braces at 3 feet 6 inches. b. Static Load: 75 lb/ft of shelf minimum. c. For heavy duty applications in pantry and garage applications space support brace on 2 feet. d. Back Clips and Down Back Clips shall be Tri-Loc II Patented hollow wall anchoring system. 2. Material: Minimum requirements. a. Steel Rod: Grade C 1008 cold drawn steel rod. Tensile strength of 100 ksi. b. Front Rods and Studs: 0.306 inch diameter. c. Back Rods: 0.243 inch diameter. d. Cross Wire Spacing: 1 inch spacing. 0.120 inch diameter for one inch spaced standard 20 inches shelf. 0.105 inch diameter for one inch spaced standard mesh shelf. PAGE 1
REVISED: 09/03/13 e. Cross Wire Spacing: 1/2 inch spacing. 0.0915 inch diameter for one-half inch spaced tight mesh shelf. 3. Shelving: a. Hanging Shelf with Open Slide: 12 inches deep by length as shown on Drawings. b. Storage Shelf: 12 inches deep by length as shown on Drawings. 4. Mounting Hardware: Manufacturer's standard components including anchor clips, end brackets, angled support braces and end caps, including the following: C. Finish: a. Side Wall Bracket: As required. Shelf side wall interface. b. Support Brace: Maximum 42 inches and every open end Anchor Back Clips. c. Fasteners, clips, caps and touch-up all as required. d. Down Back Clips. 1. Electrostatic applied oven cured epoxy at all surfaces to 3 to 5 mil thickness. a. Color: Pure White D. Configurations: 1. King Guestroom Wire Shelves: (Drawing A410) 2. Accessible King Guestroom Wire Shelves: (Drawing A 411) a. Two (2) shelves to be provided full width of closet mounted at 48 and 58 inches above finished floor. Hanging rod to be located under open section of bottom shelf. b. Three (3) additional 12 wide stacked shelves located to one side of closet below bottom shelf. 1) Storage Shelves to be located at the following intervals: 12, 24, and 36. 2) Shelf Depth: 12 inches. c. Parts List: The following is a parts list for this configuration. List shall be verified by Closet 1 (Up to 30 Wide) PAGE 2 FILE: 10-105723_13-C-Wire Closet And Utility Shelving CFRST SPECMSTR-NEW BUILD 2013, Marriott International, Inc.
(3) 2 1210-1212-11 12" D Storage Shelf - White (1) 3 1210-1212-11 12" D Storage Shelf - White 12 1430-6620-11 Versa-Clip w/ Tri-Loc II Anchor - White 7 1430-6621-11 Side Wall Bracket w/tri-loc II Anchor - White 5 1430-6665-11 Adjustable Pole Clip- White 2 1430-6671-11 Base Cap - White 1 1430-6672-11 70" Support Pole- White 28 1430-6693-11 Medium End Cap - White 12 1430-6694-11 Large End Cap - White 3. Extended King Guestroom Wire Shelves: (Drawing A412) 4. King Suite Guestroom Wire Shelves: (Drawing A413) Closet 1 (Up to 32 Wide) Closet 2 (Up to 26 Wide) 5. Double/Queen Guestroom Wire Shelves: (Drawing A 414) PAGE 3
REVISED: 09/03/13 4 1430-6693-11 Medium End Cap White 4 1430-6694-11 Large End Cap White 6. Accessible Double/Queen Guestroom Wire Shelves: (Drawing A 415) a. Two (2) shelves to be provided full width of closet mounted at 48 and 58 inches above finished floor. Hanging rod to be located under open section of bottom shelf. b. Three (3) additional 12 wide stacked shelves located to one side of closet below bottom shelf. 1) Storage Shelves to be located at the following intervals: 12, 24, and 36. 2) Shelf Depth: 12 inches. c. Parts List: The following is a parts list for this configuration. List shall be verified by Closet 1 (Up to 30 Wide) (3) 2 1210-1212-11 12" D Storage Shelf - White (1) 3 1210-1212-11 12" D Storage Shelf - White 12 1430-6620-11 Versa-Clip w/ Tri-Loc II Anchor - White 7 1430-6621-11 Side Wall Bracket w/tri-loc II Anchor - White 5 1430-6665-11 Adjustable Pole Clip- White 2 1430-6671-11 Base Cap - White 1 1430-6672-11 70" Support Pole- White 28 1430-6693-11 Medium End Cap - White 12 1430-6694-11 Large End Cap - White 7. Extended Double/Queen Guestroom Wire Shelves: (Drawing A 416) PAGE 4 FILE: 10-105723_13-C-Wire Closet And Utility Shelving CFRST SPECMSTR-NEW BUILD 2013, Marriott International, Inc.
4 1430-6693-11 Medium End Cap White 4 1430-6694-11 Large End Cap White 8. Double/Queen Inline Suite Guestroom Wire Shelves: (Drawing A 417) PART 3 EXECUTION 3.01 INSTALLATION A. Install in accordance with manufacturer's published instructions, square and plumb, secured rigidly in position. 1. Layout scheduled components prior to installation to verify wall to wall and floor to ceiling heights, widths, plumb and flatness of surfaces. 2. Prepare anchor locations and select anchor types using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions. END OF SECTION PAGE 5