Model Name : Features : ㅡ Flickerless ㅡ Full-protection provided: OCP/OVP/OTP/SCP/OLP ㅡ Low Power Dissipation (Stand-by mode : <0.5Wh ) ㅡ Wide Vout : 25 ~ 46Vdc ㅡ UL8750 / UL1310 ㅡ Compliant with CB, CE, UL safety requirements for LED lighting ㅡ Constant Current Type ㅡ IP67 E480967
Electrical specification No. 1 13 14 25 Dielectric Input to Output 3.75 - - 30 Withstand Voltage Surge ESD Item 2 Variable Input Voltage 108-300 Vac 3 Maximum Input Current - - 0.6 Arms 4 5 Power Factor (PF) 90 - - % 1) 6 Total Harmonic Distortion (THD) - - 20 % 1) 15 16 17 18 19 20 21 22 26 27 28 29 31 Nominal Input Voltage Nominal Input Frequency Turn-on Delay Adjustable of LED Current 12V Output Voltage 12V Output Voltage Ripple - - ± 1.2 Vdc 20MHz Bandwidth, 2) 12V Output Current STBY Power Dissipation Output Open LED Protection Output Short Circuit Protection - - - - Storage Temperature Operating Temperature Case Temperature (Tc) - 50 85 Input to Case Output to Case Line to Line Line to Ground Contact Discharge Air Discharge -40 25 80-40 25 50 23 Humidity 20-85 % Min Typ Max Unit Remark 120 220 277 47 50/60 63 7 Inrush Current - - 60 A 8 Electrical Efficiency 85 88 - % 2) 9 10 11 12 LED Output Current LED Output Current Ripple LED Output Voltage - - 0.5 998 1050 1103 - - 105 25-46 700-1050 10.8 12 13.2 - - 100 - - 0.5 - - 59 24 Insulation Resistance 10 - - MΩ 3.75 - - 0.5 - - 6 7-8 9-4 - - 8 - - Vac Hz s ma ma Vdc ma Wh Vdc @46Vdc Load ma 20 MHz Bandwidth, 2) Vdc @Cold Start, 3) Rset 2) LED Off_Remote Low @Vpeak No Damage Ta = 59 500Vdc between Input & Output Apply for 1 minute 6) 4) 4) 5) 5)
Application Notes 1) Test Condition:120/277Vac 50/60Hz Input,Typical LED Load,Ambient Temperature 25, Measure at the cable-end 2) Test Condition: 220Vac 60Hz Input, LED Max. Load, 30min Aging, Ambient Temperature 25 3) The interval of turn on/off should be over 1sec. 4) Surge Specification above is higher than IEC/EN 61000-4-5 Level 4 (Differential 2, Common 4 ) 5) The metal case of the LED driver must be connected with F.G 6) ESD Specification above meets IEC/EN 61000-4-2 Requirements (Contact Level 2, Air Level 3) 7) The metal case of the driver should be grounded. 8) Determined by Paragraph 34.1.2, UL1310 or Paragraph 8.4.2, UL8750, EN61347-1, EN61347-2-13 Safety Standards Including safety requirements above, the LED driver complies with the following safety standards: No. Item Description 1 UL8750, UL1310 UL Safety Standards (Class 2, Dry and Damp Location) 2 IEC/EN 55015 Conducted and Radiated Emission Test 3 IEC/EN 61000-3-2 Harmonic current emissions: Class C 4 IEC/EN 61000-3-3 Voltage Fluctuations and Flicker 5 IEC/EN 61000-4-2 Electrostatic Discharge (ESD): Contact Level 2, Air Level 3 6 IEC/EN 61000-4-3 Radio-frequency Electromagnetic Fields 7 IEC/EN 61000-4-4 Electrical Fast Transients (EFT) 8 IEC/EN 61000-4-5 Surges: Level 4 9 IEC/EN 61000-4-6 Injected Currents 10 IEC/EN 61000-4-8 Power Frequency Magnetic Fields 11 IEC/EN 61000-4-11 Voltage Dips and Short Interruptions
Operating window Preliminary *Currently Measurement Data Life Time vs Tcase 120000 100000 Life Time [hrs] 80000 60000 40000 20000 120Vac_15S(46V) 220Vac_15S(46V) 0 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Tc [ ] Remark) LED Driver has a rated lifetime of 50,000 hours @ Tc 70
*Currently Measurement Data Power Factor(%) 100.00% 9LED-700mA 90.00% 9LED-1050mA 80.00% 12LED-700mA 70.00% 12LED-1050mA 60.00% 15LED-700mA 50.00% 15LED-1050mA 120 220 277 Input Voltage (Vac) Power Factor THD(%) THD 35.00% 30.00% 25.00% 20.00% 15.00% 10.00% 5.00% 0.00% 120 220 277 Input Voltage (Vac) 9LED-700mA 9LED-1050mA 12LED-700mA 12LED-1050mA 15LED-700mA 15LED-1050mA Efficiency(%) Eff 100.00% 90.00% 80.00% 70.00% 60.00% 50.00% 120 220 277 Input Voltage (Vac) 9LED-700mA 9LED-1050mA 12LED-700mA 12LED-1050mA 15LED-700mA 15LED-1050mA
Output Current( ma ) Preliminary *Currently Measurement Data Current 1200.00 1000.00 800.00 600.00 400.00 200.00 0.00 120 220 277 Input Voltage (Vac) 9LED-700mA 9LED-1050mA 12LED-700mA 12LED-1050mA 15LED-700mA 15LED-1050mA Dimming curve Current 1200.00 1000.00 800.00 600.00 400.00 200.00 0.00 10 9.3 9 8 7 6 5 4 3 2 1 0 Input Voltage (Vac) 9LED-700mA 9LED-1050mA 12LED-700mA 12LED-1050mA 15LED-700mA 15LED-1050mA Adjustable Of Current( Rset ) LED Current [ma] 1100 1050 1000 950 900 850 800 750 700 910 9,100 91,000 910,000 Rset [Ω] Rset
Mechanical Specification TOP BOTTOM Enclosure Size Unit Width Length Height Mount Length Overall Length mm 53.6 177.6 33.9 185.4 192.6 inch 2.11 6.99 1.33 7.30 7.58 Case Material : Aluminium
Wiring Diagram LIVE : Black Neutral : White Caution L N 1) Before installing LED driver, AC power should be turned off. After installing LED driver, AC power should be turned on. 2) When this LED driver are installed as an independent lamp controlgear, end-customer should protect connecting leads of pri/sec. cable with a certified element. 3) Waterproof connector or Junction box can be assembled with output cables for operating in dry/wet/damp or outdoor environment. LED Control gear 4) Wires should be less than 1m when installed in final equipment L L E S D R V G G LED + : Red LED : Blue Vsen : White Rset : Orange DIM : Violet RMT : Green 12V : Yellow GND : Black GND : Blue 2nd Signal Description Name Feature Purpose Vsen check LED Out Voltage Monotoring LED Open/Short (for Connectivity Module) Rset Adjustable of current Control LED Output Current DIM RMT Dimming LED On/Off Control Brightness Stand by Mode 12V Control Source Supply Controller Power GND 2nd GND Signal GND GND 2nd GND Signal GND Rating Label Drawing
Barcode Label Solu M Box Label Material Code ITEM LOT No REV. A** ********* MAKER USER Model Code SOLUM Model Code SOLUM LOT NO & Quantity of Products Quantity [PCS] 24 SOLUM EXP. Date 20**.**.** ~ 20**.**.** Product Date ~ After 5 years ************* **** ********* USER Barcode
Packing Drawing 1. Out Box Dimmension Weight Quantity 540(L) 355(W) 170(H) [mm] < 14Kg 24EA / 1Box TRY BODY NIL PAD OUT BOX 2. Pallet