PWM60 series IP67 ~ File Name:PWM60SPEC 20160630
SPECIFICATION MODEL OUTPUT DC VOLTAGE RATED CURRENT RATED POWER 60W PWM Output LED Driver SETUP, RISE TIME HOLD UP TIME (Typ.) Note.2 VOLTAGE RANGE Note. 3 FREQUENCY RANGE POWER FACTOR (Typ.) WORKING HUMIDITY 20 ~ 95% RH noncondensing ENVIRONMENT STORAGE TEMP., HUMIDITY 40 ~ 80, 10 ~ 95% RH SAFETY & EMC OTHERS NOTE DIMMING RANGE PWM FREQUENCY (Typ.) TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS Note.5 MTBF DIMENSION PACKING 0 ~ 100% 300Hz 500ms, 80ms/ 115AC or 230VAC 16ms/115VAC or 230VAC 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz PF>0.97/115VAC, PF>0.95/230VAC, PF>0.92/277VAC @ full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes PWM60 series PWM6012 PWM6024 PWM6036 PWM6048 TOTAL HARMONIC DISTORTION THD< 20%(@load 60%/115VAC, 230VAC; @load 75%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION section) INPUT EFFICIENCY (Typ.) 86% 89% 90% 90% AC CURRENT (Typ.) 0.8A / 115VAC 0.4A / 230VAC 0.32A / 277VAC INRUSH CURRENT (Typ.) MAX. NO. of PSUs on 16A CIRCUIT BREAKER COLD START 50A(twidth=270 μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 9 units (circuit breaker of type B) / 16 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT <0.25mA / 277VAC <0.5W OVERLOAD 108 ~ 120% rated output power Hiccup mode, recovers automatically after fault condition is removed SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed PROTECTION 15 ~ 17V 28 ~ 34V 41 ~ 46V 54 ~ 60V OVER VOLTAGE Shut down o/p voltage, repower on to recover OVER TEMPERATURE Shut down o/p voltage, repower on to recover WORKING TEMP. Tcase=40 ~ 85 (Please refer to OUTPUT LOAD vs TEMPERATURE section) MAX. CASE TEMP. Tcase=85 WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION Note.6 EMC IMMUNITY 12V 24V 36V 48V 5A 2.5A 1.67A 1.25A 60W 60W 60.12W 60W ± 0.03%/ (0 ~ 50 ) UL8750( type HL ), CSA C22.2 No. 250.1312; ENEC EN613471, EN61347213 independent,en62384, IP67 approved; Design refer to EN603351 I/PO/P:3.75KVAC I/PO/P:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN6100032 Class C (@load 60%) ; EN6100033 Compliance to EN6100042,3,4,5,6,8,11; EN61547, light industry level (surge immunity LineLine 2KV) 996K hrs min. Telcordia SR332 (Bellcore) ; 271.03K hrs min. MILHDBK217F (25 ) 150*53*35mm (L*W*H) 0.49Kg;30pcs/15.7Kg/1.0CUFT File Name:PWM60SPEC 20160630
PWM60 series DIMMING OPERATION AC/L(Brown) AC/N(Blue) SJTW 18AWG 2C UL2464 18AWG 2C(Vo,Vo) UL2464 22AWG 2C(DIM,DIM) Vo(Red) Vo(Black) DIM(Blue) DIM(White) Dimming principle for PWM style output Dimming is achieved by varying the duty cycle of the output current. Output DC current ON TON Duty cycle(%) = 100% T Io=0A TON OFF Output PWM frequency : 300Hz fixed (Typ.) T 3 in 1 dimming function (for BlankType) Apply one of the three methodologies between DIM and DIM: 0 ~ 10VDC, or 10V PWM signal or resistance. Dimming source current from power supply: 100μA (typ.) Applying additive 0 ~ 10VDC 100% 90% Vo Vo DIM DIM Additive Voltage LED Strips Duty cycle of output current (%) 80% 70% 60% 50% 40% 30% 20% 10% DO NOT connect "DIM to Vo" 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): 100% 90% Vo Vo DIM DIM LED Strips Additive PWM signal Duty cycle of output current (%) 80% 70% 60% 50% 40% 30% 20% 10% DO NOT connect "DIM to Vo" 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input File Name:PWM60SPEC 20160630
PWM60 series Applying additive resistance: 100% Vo Vo DIM DIM LED Strips Additive Resistance Duty cycle of output current (%) 90% 80% 70% 60% 50% 40% 30% 20% DO NOT connect "DIM to Vo" 10% 0% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance Note : 1. Min. duty cycle of output current is about 6% and the output current is not defined when 0%< Iout<6%. 2. The duty cycle of output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle. File Name:PWM60SPEC 20160630
PWM60 series OUTPUT LOAD vs TEMPERATURE 100 100 80 60 230VAC Input only 80 60 230VAC Input only LOAD (%) 50 40 20 LOAD (%) 40 20 40 25 10 0 15 30 50 60 70 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) 40 25 0 20 45 60 70 80 85 Tcase ( ) (HORIZONTAL) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC 100 90 80 Tcase at 75 1.0 0.9 0.8 70 0.7 277V LOAD (%) 60 50 40 PF 0.6 0.5 0.4 0.3 230V 115V 90 100 125 135 145 155 165 175 180 200 230 305 INPUT VOLTAGE (V) 60Hz 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD (60W) Derating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD PWM60 series possess superior working efficiency that up to 90% can be reached in field applications. 48V Model, Tcase at 75 48V Model, Tcase at 75 20% THD 18% 16% 14% 12% 10% 8% 6% 4% 2% 0% 50% 60% 70% 80% 90% 100% 277VAC 230VAC 115VAC EFFICIENCY(%) 92% 90% 88% 86% 84% 82% 80% 78% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 277V 230V 115V LOAD LOAD File Name:PWM60SPEC 20160630
PWM60 series LIFE TIME 120 100 LIFETIME(Kh) 80 60 40 20 0 25 35 45 55 65 75 85 Tc a s e ( ) File Name:PWM60SPEC 20160630
PWM60 series Block Diagram PFC fosc : 50~120KHz PWM fosc : 60~130KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT O.T.P. O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER DIMMING CIRCUIT O.L.P. DETECTION CIRCUIT Vo Vo DIM DIM O.V.P. Mechanical Specification Case No. NPF60A Unit:mm 150 5 300±20 AC/L(Brown) AC/N(Blue) SJTW 18AWG 2C ψ4.5 35 tc 300±20 UL2464 18AWG 2C(Vo,Vo) UL2464 22AWG 2C(DIM,DIM) Vo(Red) Vo(Black) DIM(Blue) DIM(White) tc : Max. Case Temperature 35 5 5 53 5 13 File Name:PWM60SPEC 20160630
PWM60 series Installation Manual Connection for Blanktype AC/L(BROWN) AC/N(BLUE) Vo(RED) Vo(BLACK) LED Strip DIM(BLUE) DIM(WHITE) 0~10Vdc or 10V PWM or resistance Dimmer Cautions Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure that it cannot be reconnected inadvertently! Keep proper ventilation around the unit and do not stack any object on it. Also a 1015 cm clearance must be kept when the adjacent device is a heat source. Mounting orientations other than standard orientation or operate under high ambient temperature may increase the internal component temperature and will require a derating in output current. Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer to its specification. For LED drivers with waterproof connectors, verify that the linkage between the unit and the lighting fixture is tight so that water cannot intrude into the system. For dimmable LED drivers, make sure that your dimming controller is capable of driving these units.pwm series require 0.15mA each unit. Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit. DO NOT connect "DIM to Vo". Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minutes. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must requalify EMC Directive on the complete installation again. For more information about installation, please refer to www.meanwell.com/webnet/search/installationsearch.html for details. File Name:PWM60SPEC 20160630