[1] Submitted by Ana White [2] on Wed, 2011-07-20 13:24 Page 1 of 24
[1] While I know it's still July, and summer for most everyone else, yesterday, while helping out at the Momplex [3], I found myself shivering all bundled up. Page 2 of 24
And this morning, the snow line dropped on the mountains. Those mountains are like a giant clock, ticking with a dropping snow line, reminding us that winter is coming very soon. Page 3 of 24
But not everyone is worried about that. Page 4 of 24
I shiver just looking at that! And it occurred to me that as much as we cringe to think of it, fall is just around the corner. And with fall comes my most favorite of Holidays, Thanksgiving. What better excuse to build a farmhouse table? We of course have lots of table plans, but when I saw the Reclaimed Wood Benchwright Farmhouse Table from Pottery Barn, [4] I just HAD to draw you up a plan. So beautiful! Page 5 of 24
The base is sized for a five foot long iron pipe [5], available at most home improvement stores in the plumbing aisles. There's tons of iron fitting that you could use to "dress" the table up with. Summary: Free woodworking plans to make a Farmhouse Table inspired by Pottery Barn Benchwright Table. Features metal stretcher and lots of details to make your table interesting and unique. Save thousands off retail the do it yourself furniture way. CategoriesProject Type: Dining Table Plans [6] Room: dining room [7] Skill Level: Intermediate [8] Style: Farmhouse Style Furniture Plans [9] Estimated Cost: $50 - $100 [10] Dimensions: Dimensions are shown above. Page 6 of 24
6-1x6 @ 6 feet long 2-1x4 @ 8 feet long 2-2x4 @ 8 feet or stud length 2-1x2 @ 8 feet long 3-2x6 @ 8 feet long 3-2x2 @ 8 feet long 1 - Black Iron Pipe 60" long, both ends threaded Bolts/Caps and Washers for decorative touches 4-6" Black Bolts with washer and Nuts (1/4" would work fine) Common Materials: 2 inch screws 3 inch screws 2 inch finish nails Elmer's Wood Glue [11] Elmer's Wood Filler [12] 120 grit sandpaper primer Dimensions: wood conditioner paint paint brush Tools: Page 7 of 24
[13] Page 8 of 24
[14] [15] [16] [17] Cut List: Legs 4-1x4 @ 29 3/8" (Bevel both ends at 10 degrees off square, short point to long point) 4-1x2 @ 21 5/8" (Both ends cut at angle 10 degrees off square, short point to long point) 4-2x4 @ 29 3/8" (Bevel both ends at 10 degrees off square, short point to long point) 2-2x6 @ 28 1/2" (End Aprons) 2-2x4 @ 31" (Stretcher) 8-1x2 @ 4 1/4" (One end cut at 10 degree angle, longest point measurement) 4-1x2 @ 16 1/8 (cut to fit - spacer) Table Page 9 of 24
2-2x6 @ 45 1/4" (Side Aprons - short point to short point measurement, both ends cut at 10 degrees off square) 3-2x2 @ 20" (Supports) 2-2x2 @ 67" (Sides) 2-2x2 @ 30" (Ends) 2-2x4 @ 33" 2-1x4 @ 33" 6-1x6 @ 67 1/8" (cut to fit) General Instructions: Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck! Page 10 of 24
[18] We'll start by making the legs. The most important part of the legs is getting your cuts right. Some of the cuts are bevels and some are angles, so pay attention in the diagrams. All angles will be ten degrees off square. Remember, you will need to assemble two sets of legs, and the legs are mirrors of each other. You can use finish nails and glue. Start by attaching the 1x4 to the top 1x2 as shown above. Step 1 Page 11 of 24
[19] Now attach the 2x4 to the legs as shown above. Use glue and 2" finish nails - don't worry, we'll be further suporting this leg shortly. Step 2 Page 12 of 24
[20] Now sandwich in the apron and stretcher as shown above. Stretcher will overhang 1/2" on each outside end. Step 3 Page 13 of 24
[21] And now simply fill in the blanks. Step 4 Page 14 of 24
[22] Once your legs are done, you can add the side aprons. Screw with 3" screws and glue - or pocket holes if you have a Kreg Jig. Step 5 Page 15 of 24
[23] And attach the supports - these will give you something to nail your top boards on too. Step 6 Page 16 of 24
[24] I'd love to see these bolted on with a iron bolt for a little extra touch. Attach with 7 1/2" overhangs on ends. Step 7 Page 17 of 24
[25] Now the end supports. Attach with screws and glue. Step 8 Page 18 of 24
[26] Step 9 Instructions: Bolt the breadboard end on as shown above. Use 6" bolts with washers as done here. [4] Step 9 Page 19 of 24
[27] Nail down the 1x4 to the ends as shown here. Step 11 And finally top with the 1x6s. Note, you can use other boards for the top, for example reclaimed wood boards for a more rustic look. Step 10 Page 20 of 24
[28] Page 21 of 24
[29] Drill holes in the stretchers and add iron pipe. Use fittings to secure pipe in place. Finishing InstructionsPreparation Instructions: Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed. Step 12 Source URL: http://www.ana-white.com/2011/07/plans/benchright-farmhouse-table Page 22 of 24
Links [1] http://www.ana-white.com/2011/07/plans/benchright-farmhouse-table [2] http://www.ana-white.com/users/ana-white [3] http://ana-white.com/momplex [4] http://www.potterybarn.com/products/benchwright-reclaimed-wooddining-table/popup/more-views.html#hero-image [5] http://www.lowes.com/pd_71477-76064-20622_4294935907?prod uctid=3373212&ntt=pipe+iron&pl=1¤turl=%2f pl_plumbing_4294935907 s%3fntt%3dpipe%2biron&facetinfo= [6] http://www.ana-white.com/category/plans/project-type/dining-tables [7] http://www.ana-white.com/category/plans/room/dining-room [8] http://www.ana-white.com/category/plans/skill-level/intermediate [9] http://www.ana-white.com/category/plans/style/farmhouse [10] http://www.ana-white.com/category/plans/estimated-cost/50-100 [11] http://elmers.com/diy [12] http://elmers.com/products/wood-filler-and-other-repair?filters=con struction# [13] https://www.ryobitools.com/power-tools/products/details/537 [14] https://www.ryobitools.com/power-tools/products/details/636 [15] https://www.ryobitools.com/power-tools/products/details/552 [16] https://www.ryobitools.com/power-tools/products/details/187 [17] https://www.ryobitools.com/power-tools/products/details/774 [18] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%204.png [19] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%205.png [20] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%206.png [21] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%207.png [22] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%2015.png [23] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%208.png [24] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%209.png [25] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%2010.png [26] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%2011.png Page 23 of 24
[27] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%2012.png [28] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%2013.png [29] http://www.ana-white.com/sites/default/files/benchright%20table% 20plans%2014.png Page 24 of 24