Assembly uide 300 Pull Out 2070 600 Easy Pull Out Swing 2070 300 Pull Out 2250 Tall 600 Easy Pull Out Swing 2250 Tall or Internal Use: I.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev3.indd
Assembly uide EORE YOU START INSTAATION SHOUD E PERORMED Y A OMPETENT PERSON ONY. THIS PRODUT OUD E DANEROUS I INORRETY INSTAED Panel A x1 ack Panel Panel x1 ase Panel Panel x2 End Panel Panel E x2 Rail egs Winged over aps x2 (Packed separately) ung over aps x2 (Packed separately) rontals x2 (Packed separately) ixing Plate (500 and above, Packed Separately) E RAKET x2 HINE MOUNTIN PATE x4 Where aplicable (Inc Screws) HINE x4 Where aplicable (Inc Screws) () x16 Wooden Dowel () x12 am Dowel (Expanding) (H) x12 am ock (K) x7 30mm Screw () x22 15mm Screw (J) x36 16mm Screw (M) x4 over ap (N) x2 Door uffer (Z) x24 Shelf Peg Plastic REQUIRED TOOS Page 1 or Internal Use: I.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev3.indd
Step 1. Seat dowel () into holes in both end panels () as shown. Assembly uide Step 2. Seat cam dowel () into holes in both end panels () as shown. Seat () cam dowel into hole as shown E E Step 3. arcass onstruction Attach Panels () & (E) to panels (), using cam dowel () & cam lock (H) (in blue), and also using dowels () (in orange) in positions as shown on. Dowel () & am Dowel () location detail N. All am ocks (H) are to be positioned facing the outside of the unit carcass, for ease of tightening. Do not use power tools with cam dowel () or cam lock (H) H Step 4. Join panels () & (E) to (). Insert cam lock (H). Do NOT tighten until Step 6. View from underside View from underside or Internal Use: I.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev3.indd Page 2
Assembly uide Step 5. Slide back panel (A) into groove of end panels (). Once back panel (A) is in position, ensure the panel is flush & square with bottom of end panels (). A E E Step 6. Hand tighten all cam locks (H), this will expand cam dowels () and tighten the unit together. Step 7. Ensure carcass is square. Secure back panel (A) with 6 x 30mm screws (K) equally spaced at the top and bottom of back panel (A) into base panels (), as shown. A K Ensure you screw into the entre of ase Panel () (9mm from bottom edge). K Page 3 or Internal Use: I.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev3.indd
Step 8. Secure each of the legs into place with 2 x 15mm screws () per leg eg position diagram TOWER UNIT Assembly uide ront Ensure legs are rotated as shown so that part of it is supporting the end panels (). ront legs should have flat edge to the front. ront Step 9. ightly hit centre peg of leg base with hammer until flush with the leg base. Step 10. Push leg firmly down into leg base. Adjust legs to 155mm before turning carcass upright. Once in situ level accordingly. or Internal Use: I.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev3.indd Page 4
Assembly uide 2006 1974 1826 1794 Step 11. Hinge mounting plate attach hinge plates onto end panels () In locations shown using 8 x 15mm screws () Hinge side to be mounted in accordance to customer kitchen plan. 846 814 846 814 626 594 626 594 K 2006 1974 126 94 Securing to Adjacent Units Screw into any side units using the 30mm screws (K) provided to secure to unit. Screw just to the rear, at the top and bottom of both sides of the unit, place a cover cap on the head to conceal it. 2070 TA 2250 Secure tower to the wall using brackets. Use 2 x 15mm screws () to secure each of the brackets to the cabinets at either side. Then screw through into the wall as shown. Screws for fixing to walls are not provided as these vary depending on your wall material and construction. Ensure appropriate fixings for wall constructions are used. Secure tower to the wall using screws through rail panel (E) into the wall as shown. Screws for fixing to walls are not provided as these vary depending on your wall material and construction. Ensure appropriate fixings for wall constructions are used. E E Page 5 or Internal Use: I.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev3.indd
300 Pull Out Please refer to separate instructions included with your Pull Out. TOWER UNIT Assembly uide Insert cover caps as shown. Reverse of rontals Winged cover cap ung cover caps Repeat on other side for Handleless rontals or Internal Use: I.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev3.indd Page 6
Assembly uide Step 12. Insert hinge where required in holes as shown. Hinges Step 13 Secure hinges by tightening 2 screws with hinge dowels attached. These are already positioned within the hinges. ixing plates Step 15. Adjust hinge to suit. As shown below. Step 14. Align doors to join together using fixing plate to the back of 600 frontal ensure a 3mm gap is maintained between each frontal once fixed together. Screw in place using 8 x 15mm screws on fixing plate. RONTA HINE ADJUSTMENT Hinge cover caps To adjust hinge using a screw driver, tighten or loosen as required at points 1 & 2. Point 1 - left - right Point 2 - side - side Step 16. it cover caps to hinge. 1 2 To Release door Pull catch as shown, to release hinge from the hinge plate. View from inside of carcass Page 7 or Internal Use: I.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev3.indd
600 Pull & Swing TOWER UNIT Please refer to separate instructions included with your pull out. Assembly uide Step 3 of pull out instructions or Steps 3 of Pull Out instructions. Use (R) screws Step 4 of pull out instructions or Steps 4 of Pull Out instructions. Use () screws Step 6 of pull out instructions or Steps 6 of Pull Out instructions. Use (R) screws or Internal Use: I.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev3.indd Page 8
Assembly uide Page 9 or Internal Use: I.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev3.indd
Assembly uide or Internal Use: I.WR.INS.044_WKIN00144_TOWER_300_600_2DrPullSwing_Rev3.indd Page 10