EMPEROR RECTAGULAR G TABLE + FOLG CHAR Assembly nstructions - Please keep for future reference 60356 60357 G TABLE x FOLG CHAR x TABLE imensions Width - 39 cm epth - 7 cm Height - 75 cm CHAR imensions Width - 6, cm epth - 7 cm Height - 70,6 cm mportant - Please read these instructions fully before starting assembly f you need help or have damaged or missing parts, call the Customer Helpline : 056 0000
Safety and Care Advice mportant - Please read these instructions fully before starting assembly Check you have all the components and tools listed on pages and 3. Remove all fittings from the plastic bags and separate them into their groups. Keep children and animals awey from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts befor starting. o not stand on the product, this could cause damage. Assemble the item as close to its final position (in the same room) as possibe. Assemble on a soft level surface to avoid damaging the unit or your floor. Parts of the assembly will be easier with people. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. Assemble on a soft level surface to avoid damaging the unit or your floor. Care and maintenance Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. ote : if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels f you have damaged or missing components, call the Customer Helpline : 056 0000 Please check you have all the panels listed below Flap x Top x 3 Back Panelx rawer Frontx 7 rawer Side Right x 6 rawer Side Left x rawer Back x 9 rawer Bottom x 5 oor x 0 rawer Slide x Wooden runner x Frame element x 3 Frame element x Frame element x 5 Frame element x 7 Flap Support x Wooden runner x9 Backrest x 6 Flap Support x Wooden runner x 3 Seat x 9 Chair Leg Left x 0 Chair Leg Right x
Components - Fittings Please check you have all the panels listed below ote : The quantities below are correct amount to complete the assembly. n some cases more fittings may be supplied then are required. A B C Large cam x Magnetic plate x E F 6 mm Screw x Base x Locking pin x 30 mm Screw x 0 G H 3 mm Screw x Magnetic Catch x J K L 75 mm Screw x 36 R 50 mm Screw x Hinge x 6 60 mm Screw x 0 O P 36 mm owel x 56 0 mm owel x Hook x S T U Hinge x V Hex Key x W Castor x Pin with mounting plate x 37 mm Screw x 6 Washer x 6 X 0 mm Screw x Z 3 mm Screw x Tools required Philips screwdriver (medium & large) Small hammer Flatblade screwdriver (medium) 3 5 6 7 9 0 3 Roler/tape measure Suitable drill bit (for use with wall plug) Eye protection (when using a hammer or glue) Ruler - Use this ruler to help correctly identify the screws 3 0 0 0 30 0 50 60 70 0 90 00 0 0 30 0 50 60 70 0
Components - Key iagram 6 3 7 3 3 5 7 7 6 6 0 9 5 7 7 3 9 0 Function of Cam and Locking Pin Step : Fix the locking pin to the wooden panel. Step : Push the wooden panel with the attached locking pin onto the other wooden panel. Step 3 : Place the cam into the hole, arrow pointing towards the locking pin. Step : Tighten : turn the cam to the right. 3 C A
Assembly nstructions Step Fix Fitting to the Table Flaps. Fix hooks P to table flaps with screw. P O F 6 Fix wooden runners to table flaps using dowel O and screw F, as shown P F Step O Assemble Left and Right Frame. nsert dowels into frame elements, as shown. Assemble the frames by fixing screw with hex key S. S 3 3 5 S 5
H Front Step 3 Assemble Carcass nsert dowels into wooden runners. Fix wooden runners with the frames using screw J. J J Step Fix Magnetic Catch to the Carcass G H K E Fix magnetic catch H using screw G. G 5 7 Assemble Flap Supports 7 6 nsert dowels into Flap Supports 7. Assemble Flap Supports using screw. Fix hinge K using screw. nsert base E to flap support 6, as shown. 6 7 7 K E 6
Step 5 Assemble Table Top and Carcass Fix hinge R to table top using screw Assemble table top and carcass using screw L Fix wooden runner 0 to the carcass using screw X. T X U R G L G U 6 6 Fix Castors to the Carcass Attach mounting plate to the carcass using screw G. Attach castor T after securing mounting plate. U T L R 0 X 7
Step 6 Fix Flap Supports Attach flap supports using screw 6 6 7 7 Step 7 Mounting the locking pins to the drawer front C Screw the locking pins C into the holes indicated on the drawer front ote : insert locking pins C as far as shown. o not over tighten. C C
Step A Assembling the drawer front to the drawer sides. Lower the drawer front the side and 6 7 onto See page Function of cam and locking pin. Place the cams A into the holes indicated, arrows pointing towards the side / locking pins. A To tighten cams : Turn to the right using a screwdriver. Slide the drawer bottom 9 into the grooves of the drawer frame. 7 6 9 Step 9 rawer assembly F Fix the drawer sides 7 and 6 the drawer back using screws F F 7 6 F 9
Step 0 Fix Fitting to the oor Attach magnetic plate using screw Z. Fix hinge K using screw Z. B B Z B K Z Z K 5 Step Fix oor to the Carcass Z 6 L Fix door 5 to the carcass using screw Z. Fix back panel 3 to the carcass using screws. L 3 L 5 Z K 0
Step Fit rawer to the Carcass O Slide the drawer onto the wooden runners. nsert wooden dowels O to secure the drawer. 5 O Step 3 Secure Table Flap to Table Top 90 5
Step Chair assembly nsert dowels to backrest and wooden runner, as shown. Fix them to chair leg 9 using screws. Place the chair on the assembled side 9 Attach the seat 3 to the assembled unit using washer W and screw V. V W V 3 W
Step 5 Chair assembly Attach the seat 3 to chair leg 0 using washer W and screw V. Complete assembly of the chair by fixing screws to chair leg 0 0 3 V W V W Assembly is complete Repeat with remaining chairs 3 f you need help or have damaged or missing parts, call the Customer Helpline : 056 0000