Premium Whiteboard and Tackboard Mounting #2 BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.27.2500) Or visit our website: www.steelcase.com 2008 Steelcase Inc. Grand Rapids, MI 9501 U.S.A. Printed in U.S.A. Page 1 of 1
NOTE: Quantity of hardware will vary per product because of the various widths. Materials List Standard and Patient Tack/Marker Board PPPW Panel Mount Spline Joint STRAPS #8 x 1/2" SELF DRILLING SCREWS REQUIRED FOR ASSEMBLY: - STRAP 2 - MARKER TRAY STRAPS STRAPS BRACKETS PANEL MOUNT BRACKETS #8 x.375" SELF DRILLING SCREWS REQUIRED FOR ASSEMBLY: - STRAP 2 - MARKER TRAY - EXTENSION BRACKET TIE PLATES #8 x 7/16" TIE PLATE SCREWS #8 x.375" SELF DRILLING SCREWS REQUIRED FOR ASSEMBLY: - STRAP 2 - MARKER TRAY MARKER TRAY WALL ANCHORS EXTENSION BRACKETS MARKER TRAY MARKER TRAY SPLINE STANDARD OR PATIENT BOARD SCREWS PPPW PANEL MOUNT WHITEBOARD OR TACKBOARD Page 2 of 1
Premium Whiteboard and Tackboard 1. Use appropriate mounting specification based on the size of your Whiteboard/Tackboard. NOTE: You may drill holes in the support bracket to install into the wall stud for strongest support. ANCHOR INTO WALL STUDS AS OFTEN AS POSSIBLE. A 77 77 71 71 65 62 B 8-1/ 8-3/16 to 2-1/ 2-3/16 to 36-1/ 36-3/16 to 30-1/ 30-3/16 to 2-1/ 2-3/16 to 18-1/ C 35-15/16 29-15/16 23-15/16 17-15/16 11-15/16 5-15/16 WALL STUD WALL STUD A C WALL STUD B A C WALL STUD B A C B A C B FLOOR FLOOR 2. Level brackets and mark holes onto wall. BRACKETS 3. Remove brackets from wall and install wall anchors.. Re-align brackets with holes and secure using screws. WALL ANCHOR SCREW Page 3 of 1
5. Align the square hole in the retention strap with the hole in the top bracket and attach the retention straps between the top bracket and the wall. Make sure each strap is aligned with and secured to a stud. NOTE: You may need to drill an extra hole in the top bracket to mount the retention strap to a wall stud. 6. Lower brackets on back of Whiteboard/Tackboard onto brackets on wall. WALL Side View WHITEBOARD/TACKBOARD STUD STRAP TOP BRACKET WHITEBOARD/TACKBOARD Page of 1
MARKER TRAY MARKER TRAY RECEIVER 7. Bend each retention strap downwards (7a) and attach to frame with a #8 x 3/8" self drilling screw (7b). 8. Slide marker tray into marker tray receiver (8a). Secure by installing two (2) #8 x 3/8" self drilling screws underneath each marker tray receiver (8b). STRAP 8a 7a SCREW 7b Side View 8b MARKER TRAY Page 5 of 1
PPPW Panel Mount Bracket Installation On-Module-Minimum Application Board Width (inches) Minimum Number of Brackets 8-1/ to 120-1/ 120-5/16 to 192-1/ 6 KEY Right-Hand Application of PPPW Bracket Left-Hand Application of PPPW Bracket LH Orientation RH Orientation Asymmetrical Off-Module Overhang Allowances and Minimum Bracket Application Board Width (inches) 60-1/ 60-5/16 to 72-1/ Minimum Number of Brackets Dimension A - Maximum Overhang (inches) 18 22 72-5/16 to 8-1/ 25 8-5/16 to 96-1/ 29 96-5/16 to 120-1/ 36 120-5/16 to 192-1/ 6 38 Standard Mounting Height and Centerline Application Typical Elevation for Board Applications Dim. A Dim. A NOTE: Bracket direction must be the same as the overhang direction. This example shows right hand bracket installation with right hand overhang. 76" * * Height of board minus 12 Bracket Typical 8" Nominal AFF Symmetrical Off-Module Overhang Allowances and Minimum Bracket Application Board Width (inches) 60-1/ 60-5/16 to 72-1/ Minimum Number of Brackets Dimension B - Maximum Overhang (inches) 18 22 Dim. B Dim. B Dim. B 72-5/16 to 8-1/ 25 8-5/16 to 96-1/ 29 Dim. B 96-5/16 to 120-1/ 36 NOTE: Dimension B must be equal on both the left and right. For example, a 60" board may have a maximum 18" overhang both left and right side. 120-5/16 to 192-1/ 6 38 Page 6 of 1
1. Break off tab on each bracket as shown. 3 2. Attach a retention strap to each of the top brackets using a #8 x 3/8" self drilling screw. NOTE: The longer width applications require a minimum of six (6) brackets. For this application, the retention straps must be mounted to the outermost top brackets. The middle top bracket(s) will not require a retention strap. 3. Insert brackets into slots as shown. 2 RH Orientation 3 Height of board minus 12 LH Orientation 1 #8 x 3/8" SELF DRILLING SCREW STRAP 1 Page 7 of 1
Side View a. *For 2 and 36 high board to be installed on E9000, Kick and Answer panels and Privacy Walls only: Install extension brackets to lower bracket on board using #8-3/8 self drilling screws. NOTE: Position extension bracket on lower brackets so that they will align and engage to lower PPPW brackets on panel. b PANEL WHITEBOARD OR TACKBOARD b. Lower brackets on back of board onto brackets on panel. EXTENSION BRACKET a WHITEBOARD OR TACKBOARD Page 8 of 1
MARKER TRAY MARKER TRAY HOLDER 5. Bend each retention strap downwards (5a) and attach to frame with #8 x 3/8" self drilling screw (5b). 6. Slide marker tray into marker tray receiver (6a). Secure by installing two (2) screws underneath each marker tray receiver (6b). STRAP 6a 5a SCREW 5b Side View 6b MARKER TRAY Page 9 of 1
Spline Joint Whiteboard Mounting 1. Use appropriate mounting specification based on the size of your whiteboard or tackboard. NOTE: You may have to drill holes in the support bracket to install into the wall stud for strongest support. A C WALL STUD B A 77 77 71 71 65 62 B 8-1/ 8-3/16 to 2-1/ 2-3/16 to 36-1/ 36-3/16 to 30-1/ 30-3/16 to 2-1/ 2-3/16 to 18-1/ C 35-15/16 29-15/16 23-15/16 17-15/16 11-15/16 5-15/16 FLOOR FLOOR 2. Level brackets and mark holes onto wall. BRACKETS 3. Remove brackets from wall and install wall anchors. WALL ANCHOR Page 10 of 1
. Re-align brackets with holes and secure using #8 x 1-1/" screws. SCREW STRAP STUD 5 TOP BRACKET 5. Align the square hole in the retention strap with the hole in the top bracket and attach the retention straps between the top bracket and the wall. Make sure each strap is aligned with and secured to a stud. NOTE: You may need to drill an extra hole in the top bracket to mount the retention strap to a wall stud. Page 11 of 1
6. Slide spline into groove at end of board. 7. Slide spline into groove second tackboard. 8. Lower tie plates onto the seam of the boards and attach in the sequence shown (inside to outside) with #8 x 7/16 screws. 6 GROOVE SPLINE 7 5 3 2 1 1 2 3 5 6" 6" TIE PLATE 8 Page 12 of 1
Side View 9. Lower brackets on back of boards onto brackets on wall using three (3) people. WALL WHITEBOARD OR TACKBOARD WHITEBOARD OR TACKBOARD Page 13 of 1
MARKER TRAY MARKER TRAY HOLDER 10. Bend each retention strap downwards (10a) and attach to frame with a #8 x 3/8" self drilling screw (10b). STRAP 11. Slide marker tray into marker tray receiver (11a). Secure by installing two (2) #8 x 3/8" self drilling screws underneath each marker tray receiver (11b). 10a 11a SCREW 10b Side View 11b MARKER TRAY Page 1 of 1