AC Input 90-64 VAC AC Input Connections: Pin No. 3 SYNRAD PS-30-750 DC Power Supply (Meanwell RSP-750-7) AC Input Terminal Pin No. Assignment Assignment Diagram Maximum mounting torque AC/N AC/L FG 8Kgf-cm Connect AC Neutral to terminal labeled AC/N Connect AC line (Hot) to terminal labeled AC/L Attach AC safety ground (Earth) to terminal labeled DC Output Terminal Pin No. Assignment DC Output Terminal Pin No. Assignment Assignment Diagram Maximum mounting torque +V, -V 0Kgf-cm +30 VDC Output DC Output Connections: Connect DC Positive (Red wire) to Positive (+) V terminal post Connect DC Positive (Black wire) to Negative (-) V terminal post For further information contact SYNRAD at.800.796.73 Rev. / 3 Jul 06 4600 Campus Place Mukilteo, WA 9875 USA.800.796.73 +.45.349.3500 of 0
(Meanwell RSP-750-7) Dimension L * w * H 50 * 7 * 4 (U) mm 9.84 * 5 *.6 (U) inch Features Universal AC input / Full range Built-in active PFC function Certificates Safety: UL/EN/IEC 60950- EMC: EN 550 / 5504 High efficiency up to 9% Forced air cooling by built-in DC fan Output voltage and current programmable Built-in remote ON-OFF control / remote sense / auxiliary power / DC OK signal Protections: Short circuit / Overload / Over voltage/ Over temperature Optional conformal coating Applications Factory control or automation apparatus Test and measurement instrument Laser related machine Burn-in facility RF application 5 years warranty For further information contact SYNRAD at.800.796.73; Rev. / 3 Jul 06 4600 Campus Place Mukilteo, WA 9875 USA.800.796.73 +.45.349.3500 of 0
Description SYNRAD PS-30-750 DC Power Supply (Meanwell RSP-750-7) RSP-750 is a 750w single output enclosed type AC/DC power supply. This series operates for 90-64VAC input voltage and offers the models with the DC output mostly demanded from the industry. Each model is cooled by the built-in fan with fan speed control, working for the temperature up to 70 o C. Moreover, RSP-750 provides vast design flexibility by equipping various built-in functions such as the output programming, remote ON-OFF control, auxiliary power, etc. Model Encoding / Order Information RSP - 750-7 Output voltage (5V/V/5V/4V/7V/48V) Output wattage Series name For further information contact SYNRAD at.800.796.73 Rev. / 3 Jul 06 4600 Campus Place Mukilteo, WA 9875 USA.800.796.73 +.45.349.3500 3 of 0
Specifications MODEL OUTPUT INPUT DC VOLTAGE RATED CURRENT SYNRAD PS-30-750 DC Power Supply (Meanwell RSP-750-7) CURRENT RANGE RATED POWER 0 ~ 00A 500W 0 ~ 6.5A 750W 0 ~ 50A 750W 0 ~ 3.3A 75.W 0 ~ 7.8A 750.6W 0 ~ 5.7A 753.6W RIPPLE & NOISE (max.) Note. 50mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p VOLTAGE ADJ. RANGE 4.75 ~ 5.5V 0 ~ 3.5V 3.5 ~ 6.5V 0 ~ 6.4V 4 ~ 30V 43 ~ 55V VOLTAGE TOLERANCE Note.3 ±.0% ±.0% ±.0% ±.0% ±.0% ±.0% LINE REGULATION ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% LOAD REGULATION ±.0% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% SETUP, RISE TIME 000ms, 50ms at full load HOLD UP TIME (Typ.) 6ms/30VAC 6ms/5VAC at full load VOLTAGE RANGE Note.5 90 ~ 64VAC 7 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) 0.97/30VAC 0.98/5VAC at full load EFFICIENCY (Typ.) 8% 87% 89% 90.5% 90.5% 9% AC CURRENT (Typ.) 5V : 5.6A/5VAC.8A/30VAC V~48V : 8.A/5VAC 3.9A/30VAC INRUSH CURRENT (Typ.) 5A/5VAC 40A/30VAC LEAKAGE CURRENT PROTECTION 5.75 ~ 6.75V 3.8 ~ 6.8V 7 ~ 0.5V 7.6 ~ 3.4V 3 ~ 36.5V 56.6 ~ 66.V OVER VOLTAGE (OVP) Protection type : Shut down o/p voltage, re-power on to recover OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down OUTPUT VOLTAGE PROGRAMMABLE(PV) Adjustment of output voltage is allowable to 40 ~ 0% of nominal output voltage. Please refer to the Function Manual. OUTPUT CURRENT PROGRAMMABLE(PC) Adjustment of output voltage is allowable to 40 ~ 0% of rated current. Please refer to the Function Manual. FUNCTION AUXILIARY POWER V @ 0.A ; tolerance : ± 0% REMOTE ON-OFF CONTROL Power on : short between Remote ON-OFF(pin3) & V-AUX(pin4) on Power off : open between Remote ON-OFF(pin3) & -AUX(pin4) on DC OK SIGNAL The TTL signal out, power supply turn on = 0 ~ V ; power supply turn off = 3.3 ~ 5.6V WORKING TEMP. -30 ~ +70 (Refer to "Derating Curve") ENVIRONMENT SAFETY & EMC (Note 4) OTHERS NOTE OVERLOAD WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF DIMENSION PACKING RSP-750-5 5V 00A <.0mA / 40VAC 05 ~ 5% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 0 ~ 90% RH non-condensing -40 ~ +85, 0 ~ 95% RH RSP-750- RSP-750-5 RSP-750-4 RSP-750-7 RSP-750-48 V 5V 4V 7V 48V 6.5A 50A 3.3A 7.8A 5.7A ± 0.03%/ (0 ~ 50 ) 0 ~ 500Hz, G 0min./cycle, 60min. each along X, Y, Z axes UL60950-, TUV EN60950- approved I/P-O/P:3KVAC I/P-FG:KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:00M Ohms / 500VDC / 5 / 70% RH Parameter Standard Test Level / Note Conducted EN550 (CISPR) / EN550 (CISPR) Class B Radiated EN550 (CISPR) / EN550 (CISPR) Class B Harmonic Current EN6000-3- ----- Voltage Flicker EN6000-3-3 ----- EN5504, EN604-3, EN6000-6- Parameter Standard Test Level / Note ESD EN6000-4- Level 3, 8KV air ; Level, 4KV contact Radiated EN6000-4-3 Level 3 EFT / Burst EN6000-4-4 Level 3 Surge EN6000-4-5 Level 4, KV/Line-Line 4KV/Line-Earth Conducted EN6000-4-6 Level 3 Magnetic Field EN6000-4-8 Level 4 Voltage Dips and Interruptions EN6000-4- >95% dip 0.5 periods, 30% dip 5 periods, >95% interruptions 50 periods 336.9K hrs min. Telcordia SR-33 (Bellcore) ; 09.K hrs min. MIL-HDBK-7F (5 )7F (5 ) 50*7*4mm (L*W*H).64Kg; 6pcs/0.8Kg/.CUFT For further information contact SYNRAD at.800.796.73; Rev. / 3 Jul 06 4600 Campus Place Mukilteo, WA 9875 USA.800.796.73 +.45.349.3500 4 of 0
(Meanwell RSP-750-7) Block Diagram I/P EMI FILTER ACTIVE INRUSH CURRENT LIMITING RECTIFIERS & PFC POWER SWITCHING O.L.P. RECTIFIERS & FILTER +S +V -V -S PFC fosc : 90KHz PWM fosc : 70KHz PFC CONTROL PWM CONTROL DETECTION CIRCUIT DC OK PV O.V.P. AUX POWER FAN RECTIFIERS CONTROL ON/OFF RECTIFIERS & FILTER REMOTE ON-OFF AUX POWER(V/0.A) AUX GND Static Characteristics 00 INPUT MODEL 5V V 5V 90 80 00~64VAC 500W 00A 750W 6.5A 750W 50A LOAD (%) 70 60 50 40 90VAC MODEL INPUT 00~64VAC 450W 90A 4V 75.W 3.3A 675W 56.5A 7V 750.6W 7.8A 675W 45A 48V 753.6W 5.7A 90 95 00 5 INPUT VOLTAGE (VAC) 60Hz 64 90VAC 676.08W 8.7A 675.54W 5.0A 678.4W 4.3A Derating Curve Efficiency vs Load (48V Model) 95 00 90 LOAD (%) 80 60 50 40 0 EFFICIENCY (%) 85 80 75 30V -30 0 0 0 30 40 50 60 70 AMBIENT TEMPERATURE ( ) (HORIZONTAL) 70 0% 0% 30% 40% 50% 60% 70% 80% 90% 00% LOAD The curve above is measured at 30VAC. For further information contact SYNRAD at.800.796.73 Rev. / 3 Jul 06 4600 Campus Place Mukilteo, WA 9875 USA.800.796.73 +.45.349.3500 5 of 0
(Meanwell RSP-750-7) Function Manual.Remote Sense The remote sensing compensates voltage drop on the load wiring up to 0.5V. 3 5 7 3 TB 3 +S -S PV PC +VS -VS PS PO 4 6 8 DC_OK GND REMOTE ON-OFF GND G-AUX V-AUX 4 -V +V LOAD PIN3 -S - + PIN +S 4 Fig. The +S signal should be connected to the positive terminal of the load whereas -S signal to the negative terminal. By factory default, on, Remote ON-OFF (pin3) and V-AUX (pin4), PV(pin5) and PS (pin6), and PC (pin7) and PO (pin8, respectively, are shorted when shipped. The power supply will have no output if the shorting connector is not assembled unless certain functin needs to be activated..remote ON-OFF The power supply can be turned ON/OFF by using the Remote ON-OFF function. TB 3 3 5 7 +S -S PV PC +VS -VS PS PO 3 REMOTE DC_OK GND ON-OFF GND G-AUX V-AUX SW -V LOAD - + +V 4 4 6 8 4 Fig. Between Remote ON-OFF(pin3) and V-AUX(pin4) SW close (Short) SW open (Open) Power Supply Status ON OFF When multiple power supplies need to turn ON/OFF simultaneously by Remote ON-OFF control, -S & -V on, as well as +S & +V, on each power supply should be connected. For further information contact SYNRAD at.800.796.73; Rev. / 3 Jul 06 4600 Campus Place Mukilteo, WA 9875 USA.800.796.73 +.45.349.3500 6 of 0
(Meanwell RSP-750-7) 3. Output Voltage Programming (or, PV / remote voltage programming / remote adjust / margin programming / dynamic voltage trim) In addition to the adjustment via the built-in potentiometer, the output voltage can be trimmed to 40~0% of the nominal voltage by applying EXTERNAL VOLTAGE. Vout OVP 0%(Typ.) OUTPUT VOLTAGE (%) 0 0 00 80 60 40 0 Non-Linear UVP 0%(Typ.) 3 EXTERNAL VOLTAGE (VDC) 4 5 5.5 6 PV(Referenced to GND) If EXTERNAL VOLTAGE (VDC) <0.5V,the power supply may enter under voltage protection; it needs to be restarted to work. 3 5 7 +S +VS -S PV -VS 4 8 External Voltage (~5.5VDC) PS PO Fig 3. 3 PC DC_OK GND REMOTE ON-OFF GND G-AUX V-AUX 4 Caution: By factory default, the Output Voltage Programming is not activated, and PV (pin5) and PS(pin6) are shorted by connector. Whenever this function is not needed to activate, as assumed in other sections diagrams, please keep PV (pin5) and PS(pin6) shorted ; other wise, the power supply will have no output. 4. Output Current Programming (or, PC / remote current programming / dynamic current trim) The output current can be trimmed to 40~0% of the rated current by applying EXTERNAL VOLTAGE. Io Io 5%(Typ.) OUTPUT CURRENT (%) 0 0 00 80 60 40 0 Non-Linear 3 +S +VS 4 External Voltage (~5.5VDC) 5 7 -S PV -VS 6 PS PC DC_OK GND REMOTE ON-OFF PO 3 GND G-AUX V-AUX 4 3 4 5 5.5 6 EXTERNAL VOLTAGE (VDC) PC(Referenced to GND) Fig 4. Caution: By factory default, the Output Current Programming is not activated, and PC(pin7) and PO(pin8) are shorted by connector. Whenever this function is not needed to activate, as assumed in other sections diagrams, please keep PC(pin7) and PO(pin8) shorted ; otherwise, the power supply will have no output. TB 3 -V LOAD - + +V 4 For further information contact SYNRAD at.800.796.73 Rev. / 3 Jul 06 4600 Campus Place Mukilteo, WA 9875 USA.800.796.73 +.45.349.3500 7 of 0
(Meanwell RSP-750-7) 5.DC_OK signal "DC_OK" is an open collector signal. It indicates the output status of the power supply. It can operate in two ways : One is sinking current from external TTL signal ; the other is sending out a TTL voltage signal. Sinking current from external TTL signal: The maximum sink current is 0mA and the maximum external voltage is 5.6V. Sending out TTL voltage signal : Between DC- OK(pin9) and GND(pin0&) Output Status 0 ~ V 3.3 ~ 5.6V Power supply ON Power supply OFF 3 5 7 9 3 TB 3 +S +VS -S PV -VS PS 4 6 8 PC PO DC_OK GND REMOTE ON-OFF GND G-AUX V-AUX 4 -V LOAD - + +V 4 Fig 5. For further information contact SYNRAD at.800.796.73; Rev. / 3 Jul 06 4600 Campus Place Mukilteo, WA 9875 USA.800.796.73 +.45.349.3500 8 of 0
(Meanwell RSP-750-7) Mechanical Specification Case No.A Unit:mm 4 0.5 36 6 3-M4 L=6 50 3.5 33.5 5.4 7.8 7 8.5 SVR5 -V +V 4 3 90 63.5 Air flow direction 7 0 TB 3 3-M4 L=4 0.5 3-M4 L=6 5.4 6 36 7.8 Mounting Instruction Hole No. Recommended Screw Size MAX. Penetration Depth L Recommended mounting torque M4 M4 6mm 4mm Control Pin No. Assignment () : HRS DF-4DP-DS or equivalent 3 Mating Housing HRS DF-4DS or equivalent 4 Terminal HRS DF-**SC or equivalent 7~Kgf-cm 7~Kgf-cm Mounting Surface Mounting Screw L Chassis of RSP-750 Pin No. Function Description +S Positive sensing for remote sense. 3 +VS -S +V Signal. The +VS should be connected to the +S to reduce the noise when "output voltage programming" function is in use. Negative sensing for remote sense. 4 -VS -V Signal. The -VS should be connected to the -S to reduce the noise when "output voltage programming" function is in use. 5 PV Connect to external DC voltage source for output voltage programming, referenced to pin 0, (GND). 6 7 8 PS PC PO Reference pin regarding output voltage programming. Please refer to the Function Manual. Connect to external DC voltage source for output current programming. Reference pin regarding output current programming. Please refer to the Function Manual. 9 0, DC_OK GND G-AUX Open collector signal, referenced to pin0,(gnd). Low when PSU turns on. The maximum sink current is 0mA and the maximum external voltage is 5.6V. These pins connect to the negative terminal (-V). Return for DC_OK Signal output. Auxiliary voltage output ground. The signal return is isolated from the output terminals (+V & -V). 3 REMOTE Turns the output on and off by electrical or dry contact between pin 3 ( ON/OFF) and pin 4 (V-AUX). ON-OFF Short: Power ON, Open: Power OFF. 4 Auxiliary voltage output, 0.8~3.V, referenced to pin (G-AUX). V-AUX The maximum load current is 0.A. This output is not controlled by the "remote ON/OFF control". For further information contact SYNRAD at.800.796.73 Rev. / 3 Jul 06 4600 Campus Place Mukilteo, WA 9875 USA.800.796.73 +.45.349.3500 9 of 0
(Meanwell RSP-750-7) AC Input Terminal Pin No. Assignment Pin No. 3 Assignment Diagram Maximum mounting torque AC/N AC/L 8Kgf-cm FG DC Output Terminal Pin No. Assignment Assignment Diagram Maximum mounting torque +V, -V 0Kgf-cm Installation Manual Please refer to : http://www.meanwell.com/webnet/search/installationsearch.html For further information contact SYNRAD at.800.796.73; Rev. / 3 Jul 06 4600 Campus Place Mukilteo, WA 9875 USA.800.796.73 +.45.349.3500 0 of 0