2017 Pure Lighting. All Rights Reserved. Installation Instructions For Reveal IS# 902-RV-24VDC-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1196 Fax: 773-883-6128 www.purelighting.com info@purelighting.com IMPORTAT IFORMATIO - Reveal channel can be used as a toe kick or for cove lighting. - This instruction shows a typical installation. - It is recommended more than one person to install the Reveal Channel. SAVE THESE ISTRUCTIOS! Install the Junction Box (C-1RE-JBOX) A HORIZOTAL ORIETATIO B #8 SCREW ADJUSTABLE MOUTIG BAR PHILLIPS SCREW MOUTIG BRACKET 3 4 BOX BOX 1 2 VERTICAL ORIETATIO ADJUSTABLE MOUTIG BAR OTE: The adjustable mounting bars mount to studs that are spaced 13" to 24" apart. 2: Select the location between the two studs for the junction box to be mounted. 1: Mount each adjustable mounting bar to one side of the junction box (mounts to any side of the housing depending on the orientation of the channel) and secure them with the mounting brackets and two Phillips screws provided. 3: Place the adjustable mounting bars between the studs. 4: Make sure the lips on the adjustable mounting bars are against the studs. Secure the adjustable bars to the studs with the eight #8 screws. C CUTOUT TEMPLATE BOX D CODUIT BOX 5 7 6 FROM REMOTE PHILLIPS SCREW 5: Remove the two #4-40 screws to pull the drywall cutout template completely off the junction box face. Save the template and screws for later use. 1 6: Remove a knockout on the junction box to install conduit into the power feed electrical box. 7: Install the conduit and run the low voltage 24VDC power wires.
E 3.00" 1.06" 8 F BOX 2.80" 2.25" 9 11 0.38" 10 CUTOUT TEMPLATE JAB SAW 11:Install the drywall. 8: Mark a location on the drywall where the junction box will be located. 9: Trace the drywall cutout template onto the drywall at the junction box location. 10: Remove drywall cutout template and cut out the marked area using a jab saw or other appropriate tool to expose the junction box. G MARKIG 14 12 LEGTH OF 12 CLOSE UP BOX SLOT START 13 2.25" CUTOUT OPEIG JAB SAW 12: Using the drywall opening as reference, mark 2.25" wide lines, the complete length of the channel along the drywall. 13: Cut out the mark lines on the drywall using a jab saw or other appropriate tool. 14: Mark the location to the studs for future reference. 2
H I ED CAP CODUIT 17 BOX 15 16 SCREWS 18 OTE: Remote power supply wires must be present in the junction box. Refer to instructions provided with the power supply. 15: Connect the red power supply (24VDC+) wires to each red power wire with a wire nut inside the electrical box. 18: Install the power feed end cap to the end of the channel that will be aligned with the junction box with the supplied screws. 16: Connect the black power supply (24VDC-) wires to each black power wire with a wire nut inside the electrical box. 17: Place the wire nut connections inside junction box. J JOIIG ROD K TAKE UP BOX LED SECTIO DEAD ED CAP #6-32 SCREWS 19 20 21 OTE: Channel may be cut in the field. For installation over 120" join two or more Reveal channels together. 19: Insert joining rods halfway into the channel. 20: Slide another channel onto the joining rods. 21: Install the dead end cap and take up box to the end of the channel opposite of the junction box using the supplied screws. Ensure the slot of the dead end cap aligns with the LED section of the channel. 3
L POWER COECTOR M DRY WALL SCREW #4-40 SCREW 22 25 23 24 OTE: Test the LED strip before securing the channel to the drywall. 22: Align the "" marking on the LED strip with the red wire of the power connector. Push the male connector of the LED strip into the female connector of the power cables. Inspect the strip for any irregularities. ED CAP 23: Align the power feed end cap into the junction box opening slot and push the channel into the drywall cutout. 24: Make sure the channel is aligned straight using a level. 25: Secure the channel using the two #4-40 screws to the junction box (same screws as in step 5 page 1). Fasten the drywall screws through the pre-drilled holes onto the studs. If necessary drill new holes on channel flange where they line up with the studs using the #6 X 1-5/8" square trim screw with the square recess bit provided. OTE: Ensure screw heads sit flush with the channel. DRY WALL SCREW 26 O 27 30 27 29 POWER COECTOR PAPER BACKIG 26: Drill and countersink holes to the channel at marked stud positions. ED CAP 27: Secure the channel to the studs using drywall screws. OTE: If installation requires RGB, RGB+W, or Tunable White, refer to wiring diagrams on pages 7 through 9. 28: Connect the LED strip to the power connector and place the power connector into the slot in the power feed end cap. 29: Carefully remove the backing from the LED strip, making sure not to remove the tape from the back of the strip. 4 30: Firmly press down the adhesive portion of the LED strip onto the channel surface while removing the rest of the backing, making sure there are no air bubbles that can cause surface irregularities.
P TAKE UP BOX Q 31 31 BOX COVER #4-40 SCREW 32 32: Install the junction box cover onto the junction box using the #4-40 screws using a 1/16" Allen wrench. 31: Trim excess LED strip OLY at the indicated trim lines (see inset). Insert excess LED strip into the take-up box. R ULTRA THI TAPE 33 BLUE COTRACTORS TAPE 34 SIDE VIEW 33: Apply ultra thin drywall tape to the Reveal channel. Do not overlap sections of the drywall tape. 34: Cover up the opening section of the Reveal channel with contractors tape to prevent plaster and dust entering inside the channel. 35: Plaster the channel flange edge to the wall & fill screw holes (highlighted in green). Sand, paint, and finish the wall properly. 36: Remove the blue contractor tape & clean the inside of the channel. 5
IMPORTAT IFORMATIO REGARDIG ISTALLATIO AD REWORK OF SOFT STRIP LED DO gently pull up and away from the soft strip if removing to reposition. This avoids damaging the strip. DO OT pull the strip back towards itself. Doing so risks damaging the strip and making it not function. DO only ever use fingers to gently install soft strip to a surface AFTER cleaning the surface with alcohol. DO OT use any tool to install soft strip to a surface. This will damage the soft strip component. Relocating Soft Strip (Optional) S ADHESIVE TAPE REMOVE SOFT STRIP TO RELOCATE SOFT STRIP ADHESIVE TAPE OTE: If relocating the installed soft strip, make sure that the adhesive tape on back of the soft strip covers the entire strip. The adhesive tape isolates the strip from the installation surface. Damaged or inconsistent adhesive tape may cause the contacts on the back of the strip to come in contact with the conductive heat sink which will cause the strip to short and burn. Call Edge Lighting to get replacement adhesive tape and/or optional aluminum heat sink tape (SS-HR-F). 1: To remove tape residue from back of the strip, apply WD-40, Goo Gone, or a mixture of warm water and lemon oil to the corner of a clean, dry towel. Gently buff the area containing the adhesive residue until it is completely removed. APPLY ADHESIVE REMOVER AD THE BUFF OFF ADHESIVE 2 ADHESIVE BACKIG 1 2: Gently remove a few inches of the from one side of the tape backing. Attach the adhesive tape to the back of the soft strip and apply moderate pressure to affix the tape. Continue this step a few inches at the time until the entire adhesive tape is attached to back of the soft strip. 3: Refer to steps 28 through 31 on pages 4 and 5 to reinstall the LED strip. BACK SIDE OF SOFT STRIP 6
General 0-10V Configuration GRAY 0-10V 0-10V DIMMER PURPLE 0-10V RED 120VAC (HOT) BLACK (HOT) WHITE (EUTRAL) RED () 24V LED SOFT STRIP BLACK (-24VDC) IPUT 120VAC General 24VDC Configuration IPUT 120VAC 120VAC (HOT) EU WHITE (EUTRAL) 24V LED SOFT STRIP BLACK (HOT) ELV DIMMER RGB Configuration CDP COTROLLER Using LED Power Supply with RGB Soft Strip & CDP or CTP Control EXT in- EXT in+ DMX in shield out+ VDC- out- VDC+ out shield 24VDC + - L LIE COTROLLER L VDC+ VDC- LED supply + Ext in- Group 1 - Ext in+ Group 2 - DMX CABLE DMX in shield LedSync thru+ LedSync thru- LedSync shield M Group 3 - Group 4 - RGB LED SOFT STRIP DVR-RGB 7
RGB+W Configuration CDP COTROLLER Using LED Power Supply with RGB+W Soft Strip & CDP or CTP Control EXT in- EXT in+ DMX in shield out+ VDC- out- VDC+ out shield 24VDC + - L LIE COTROLLER L VDC+ VDC- LED supply + Ext in- Group 1 - Ext in+ Group 2 - DMX CABLE DMX in shield LedSync thru+ LedSync thru- LedSync shield M DVR-RGB Group 3 - Group 4 - RGB+W LED SOFT STRIP Tunable White Configuration Dual Power Supplies Controlled Via Individual ELV Dimmers ELV DIMMER WHITE (EUTRAL) IPUT 120VAC BLACK (HOT) 120VAC (HOT) EU HOT Power Supply RED -24VDC BLACK WHITE (EUTRAL) IPUT 120VAC BLACK (HOT) 120VAC (HOT) EU HOT Power Supply RED -24VDC BLACK ELV DIMMER 8
Tunable White Configuration RGB Power Supply with DMX Controller CDP/CTP or other DMX Signal From Any Compatible Controller L If using a CDP Color Dial, configure your CDP to Warm White mode using DIP switches and follow CDP operating instructions: O LED SYC OUT + LED SYC OUT - LED SYUC OUT SHIELD Power Supply + RED - BLACK 1 2 3 4 5 6 7 VDC+ VDC- DMX Cable (belden #9841 or CATS) Ext in- Ext in+ DMX in shield LedSync thru+ LedSync thru- LedSync shield M Driver LED supply + Group 1 - Group 2 - Group 3 - Group 4 - + + -- 9