ER CUSTOMER Thank you for purchasing your new piece of furniture from unelm. We put a lot of effort in the design and construction of our products to ensure they set the standard for quality, durability and ease of assembly. If for any reason you feel we haven t lived up to the high standards we set ourselves, please don t hesitate in contacting us on 0 where our team will be very keen to understand what has gone wrong and, more importantly, put it right. ER CUSTOMER The next step There is no need to feel daunted by the number of parts and fittings in front of you, we have compiled this straight forward, step-by-step guide to make sure that assembling your furniture is as easy as,,. efore you begin, we advise that you check that you have everything you need to get started. TOP TIP Find a space to spread these out across the floor before you begin assembling them. Lay each panel down in position, ready to build. It is recommended that two people assemble this product together. The full list of furniture parts, fixtures and fittings, as well as the tools you will need for assembly, can be found on page and of this manual. TOP TIP Identify all of the fittings, make sure that you have them all prepared and familiarise yourself with each component, to make things easier when you are putting it all together. Safety and Care dvice IMPORTNT - The first step you need to take is to ensure your safety! Please take the time to read and understand these instructions before assembling your furniture. eep children and animals away from the assembly area. This furniture contains small parts that could cause choking if swallowed. eep all plastic wrapping materials way from children to avoid danger of suffocation. Ensure that all packaging is disposed of carefully and responsibly. Make sure that you allow enough space to move around when assembling your furniture.
Parts & Fittings for the Indiana rawer Chest White (00), lack (0) Panels - exploded view 0 Panels - plan view Rail x mm X Top x mm Left side x mm Right side x mm L/H drawer side 0 x mm X R/H drawer side 0 x mm X rawer back. x mm X rawer base x mm X rawer front x mm X 0 ack 0 x 0mm
Fittings C E mm Metal cam x 0 Cam pin x 0mm Wooden dowel x 0 mm Metal cam x Euro screws x F rawer peg x G Panel pins x 0 H rawer wedge x I Handle x J Handle screw x Soft close runner x pair Tools required Cross slot screwdriver Hammer Tape measure The use of power tools to assemble the product is not recommended due to the risk of over tightening fixings efore you start Check the pack and make sure you have all the parts listed above. If not, contact the helpline on 0 who will be able to help you. When you are ready and sure that you have the right tools to hand, you will need plenty of space and a clean dry area for assembly. Important information The finished surface of the drawer fronts are hi-gloss, take care when cleaning, wiping and handling these panels. There is also a protective film covering the drawer front and edges, this should be removed before the handles are attached (step ). Ready? Follow this step-by-step guide Note: Insert metal dowels as far as shown.
E E Note: Insert metal dowels as far as shown.
Rear edge Ensure the cam is pressed fully into the hole and arrow pointing towards the short edges X 0 mm E E C C C C C C C
Cam lock in open position Cam lock in closed position These panels must be supported until the next step Cam lock in open position Cam lock in closed position
Cam lock in open position Cam lock in closed position Two people required to turn unit over ack of unit 0 to = C to
0 G G 0 G G G G 0 0 Two people required to stand unit upright X Ensure the cam is pressed fully into the hole and arrow pointing towards the short edges X F F X
X Note: Insert metal dowels as far as shown. X Cam lock in open position Cam lock in closed position X
H H X EFORE TTCHING THE HNLES REMOVE THE PROTECTIVE FILM FROM THE FRONT N EGES OF THE RWER FRONTS I J J X LEFT N RIGHT RWER RUNNERS 0
rop drawers onto the runners and position the pegs into the holes at the back (FIG ) and on the underside of the drawer sides (FIG ). SECON FIRST FIG. X X FIG. UNERNETH RWER REPET PROCEURE FOR THE REMINING RWERS
0 Lift green clip up and push towards the runner (arrowed below), this secures the drawer onto the drawer runner and prevents the drawer from popping out. TO SECURE RWER X REPET PROCEURE FOR THE REMNING RWERS UNERNETH RWER Nearly there! TO JUST RWER HEIGHT X TO RELESE RWER X FIRST SECON L UNERNETH RWER UNERNETH RWER To adjust drawer height turn the green wheel clockwise or anticlockwise. To remove the drawer pull out the green tab and clip back. Repeat the process for the other drawer runner then lift the drawer from runners. REPET PROCEURES FOR THE REMNING RWERS
Care and maintenance Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Finally, we hope you enjoy your furniture for many years to come and thanks again for your purchase. dunelm.com