88 5023 95C Kitchen Island with Breakfast Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. PART LIST A. Top B. Side Panel C. Middle Panel D. Side Panel H. Back Stretcher E. Back Panel F. Back Panel G. Back Piece I. Front Piece J. Base M. Divider P. Shelf S. Handle Arm K. Door L. Door N. & O. (For s, packed in a separate carton) HARDWARE LIST Q. Shelf R. Gate Leg T. Round Arm U. Knife Box Caster two lock two non-lock Small Hex Wrench Hex Wrench 13 pcs. (+1 extra) for Caster and Gate Leg 20 pcs. (+1 extra) Screw 6 pcs. (+1 extra) 6 pcs. (+1 extra) Pull Handle 8 pcs. Adjustable Pin 1 (+1 extra) Wood Plug 6 pcs.(+2 extra) Tools Required For Assembly : Phillips screwdriver Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319 servicedesk@homestyles-furniture.com Revised date : 23Mar2011
IMPORTANT Do not tighten up all the screws until each part is properly assembled. You should keep Hex Wrench in the safe place as you may need to tighten up the s in the future. Assembly Instructions 2/4 STEP 1 Attach four Casters to Base (J) with s. (See figure 1) J Locking Caster (On Front) (Figure 1) STEP 2 Attach Side Panel (B) to Base (J) with s. B C Attach Middle Panel (C) and Back Piece (G) to Base (J). G J C G E M I F H E Locking Caster (On Front) STEP 3 Slide Back Panel (E) and (F) to the unit. Attach Back Stretcher (H) and Front Piece (I) to the unit with s. D Attach Side Panel (D) and Divider (M) to the unit with s.
Assembly Instructions 3/4 STEP 4 Attach Gate Leg (R) at the back of unit with s. (See figure 2) R R (Figure 2) U B S T S P Q D P STEP 5 Assemble Handle Arm (S) to Side Panel (D) with s. Slide Round Arm (T) into place. Adjustable Pin Attach Knife Box (U) to Side Panel (B) with s. Insert Adjustable Pins into side panels and middle panels at the desired level. Place Shelf (P) and (Q).
Assembly Instructions 4/4 Screw A STEP 6 Put Screws into the pre-drilled holes at Top (A). Place Top (A) onto the unit, using s. (See figure 3) A (Figure 3) N O K K L L (Figure 4) STEP 7 Assemble Pull Handles to Door (K) and (L) with s. (See figure 4) Spring Pin Attach Door (K) by inserting the lower Spring Pin into the hole until it clicks (See figure 5) and then do the same for the upper Spring Pin. (Figure 5) Do the same process for Door (L). Slide (N) and (O) into place. STEP 8 Cover up all holes with Wood Plugs.
88 5023 95 (N) (O) N2 O2 N5 O5 PART LIST N2, O2. Back Part for each drawer,. Front Part for each drawer,. Side Part for each drawer,. Side Part for each drawer N5, O5. Base Part for each drawer HARDWARE LIST Pull Handle (short) for Base Part 1 (+1 extra) (long) for Side Part 16 pcs. (+1 extra) Assembly Instructions N2 O2 MAKE SURE ROLLER IS ON THE BACK (Figure 1) Slide the plywood Base Part (N5, O5) into the grooves on Side Parts (, ) and (, ). Be sure to push the plywood all the way forward so it meets the Front Part (, ). (See figure 2) N5 Using a Philips screwdriver, insert s (long) into the pre-drilled holes as shown, tighten half way. (See figure 1) O5 (Figure 2) Unfinished Side N2 N5 O2 O5 * If you are missing any of these parts, please contact our DMI Customer Service Department at 1-877-831-0319 or fax us at 1-800-755-2878. (Figure 3) Assemble the Pull Handle with s on the Front Part(, ). (See figure 4) Insert s (short) into the pre-drilled holes on Base Part (N5, O5), then tighten all s. (See figure 3) (Figure 4)