Skills Development Provider Accreditation Checklist Quality Council SDP Name: Centre Manager Name SDP Contact Details SDP Physical Address e.g. 17 Tonga-tinge Street, Mable Hall, 1612 Facilitator/Lecture Name Facilitator/ Trainer qualification relevant to the trade SME Name SME Employer Details SME Employer contact Ratio of candidates to Assessor e.g. 12 Candidates:1 Facilitator No. of Candidates per given time in the Venue Accreditation History (If previously accredited through the SETA System, Complete the section below ) Accredited by: SETA Name Accreditation No. Accreditation Visit Date: DD/MM/CCYY OFO Code (if applicable) Province e.g. Northern Cape Municipality e.g. Madibeng New Accreditation Information Knowledge X Practical Skills X OFO Code Specialization /Alternative Title Legacy Trade New Trade SAQA ID Signature: Page 1 of 8 Date revised 23/02/2016
Urban X Rural X Audit Visit Date DD/MM/YYYY Index of Tasks: 1. Glazing 2. Stain and varnish 3. Roof 4. Ceiling 5. Wall surfaces - P.V.A. (Brush/Roller) - Enamel Dado (Brush/Roller) 6. Window/Door frame/door 7. Colour matching 8. New surfaces 9. Old surfaces 10. Scaffolding NB: SME must ensure that all equipment were tested and found in good working condition for SDP! Hand tools Ratio Y N Comments Claw hummer 1:1 Scissors 200 mm 1:1 Mixing stick 1:1 Pencil 1:1 Paint brush (12-200 mm) 1:1 Roller 200 mm 1:1 Radiator brush 1:1 Lining Fitch 1:1 Pencil 1:1 Chalk line 1:1 Working Pots 1:1 Scrapper (different sizes) 1:1 T square (1 500 2 000 mm) 1:1 Glass cutter 1:1 Suction pad (2) 1:1 Glass pliers 1:1 Putty knife 1:1 Signature: Page 2 of 8 Date revised 23/02/2016
Mutton clothes 1:1 Wood chisel 1:1 Steel chisel 1:1 Circle glass cutter 1:1 Sheep skin roller 1:1 Mohair roller 1:1 Drop sheet 1:1 Broom 1:1 Telescopic stick 1:1 Portable drill machine 1:1 Portable belt sender 1:1 Set of spanner 1:1 Special Tools None Measuring Equipment Tape measure 3 m or 5m 1:1 Signature: Page 3 of 8 Date revised 23/02/2016
Machinery Equipments (Long Term Consumables) Scaffolding Step ladder 1 250 mm Step ladder 1 850 mm Ladder 4 260 mm Ladder (Roof) Safety Safety boots/shoes/ Protecting Flab 1:1 Safety helmet 1:1 Protective clothing 1:1 Signature: Page 4 of 8 Date revised 23/02/2016
Dust mask 1:1 Leather gloves 1:1 Gloves (rough) for glass 1:1 Gloves (smooth) for paint removing 1:1 Goggles 1:1 Safety belt 1:1 Storage for flammable material 1:1 Should be provided by candidate I, (manager of the trade test centre / skills development provider) hereby commits to comply with all the relevant OHS regulations and sections applicable to this specific trade. Signature and date Consumables Sandpaper (60 and 80 grit) Master putty Turps Stain( diffent colours) Varnish Woodfiller (different wood) Steelwool Paint remover Spirit of salt Water Etch primer/red oxide Zinchromate/Galvogrip/Culcium plumbate Signature: Page 5 of 8 Date revised 23/02/2016
Polyfiller PVA paint Universal undercoat Enamel paint (3 different colours) Anneall glass and obscure Masking tape Heavy duty glue Plaster primer Bonding liquid Pink wood primer Sending sealer paraffin Floor vanish Stoep paint Mutton clothes Mirror Mirror tape Mirror screw Silicon for mirror Masonite board Chip board Rhino board Block board Non-ferrous/ ferrous metals PVC surface Soft board Signature: Page 6 of 8 Date revised 23/02/2016
Assessment aids Cutting table House (standard) for wall, ceiling and roof. Wooden window frame 500 x 1000 mm with (440 x 285 panes) Steel window frame 1030 x 1265 mm (8 glasses) Wooden plank 300 x 500 mm Round/semi-circle window frame LOGISTICS AND LAY-OUT Cubicles (2 500 X 2 500 mm) proportional to the number of candidates/ Rooms Workshop for practical component Signature: Page 7 of 8 Date revised 23/02/2016
I the undersigned, hereby declare that all the tools/equipment/training materials/machines were checked and are the sole property of the SDP. Signature.. Accreditation recommended Yes No Constraints/Gaps: Recommendations: SME Name Signature Organizational Rep. Name Designation Signature Date: DD/MM/YYYY Date: DD/MM/YYYY Signature: Page 8 of 8 Date revised 23/02/2016