~ IP65 IP67 { A Dx
SPECIFICATION MODEL OUTPUT INPUT PROTECTION OTHERS NOTE CURRENT ADJ. RANGE Adjustable for AType only (via the builtin potentiometer) 2 ~ 4A 1.33 ~ 2.66A 1.14 ~ 2.28A VOLTAGE TOLERANCE Note.4 ±3.0% ±2.5% ±2.5% LINE REGULATION LOAD REGULATION ±1.0% ±1.0% SETUP, RISE TIME Note.6 1000ms, 80ms/115VAC 500ms, 100ms/230VAC HOLD UP TIME (Typ.) 15ms/115VAC 10ms/230VAC VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR EFFICIENCY (Typ.) AC CURRENT INRUSH CURRENT(Typ.) LEAKAGE CURRENT OVER VOLTAGE EMC IMMUNITY MTBF DIMENSION PACKING Note.5 OVER TEMPERATURE WORKING TEMP. MAX. CASE TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY & EMC ELG10024 ELG10036 ELG10042 ELG10048 ELG10054 DC VOLTAGE 24V 36V 42V 48V 54V CONSTANT CURRENT REGION Note.2 12 ~ 24V 18 ~ 36V 21 ~ 42V 24 ~ 48V 27 ~ 54V RATED CURRENT 4.0A 2.66A 2.28A 2A 1.78A 0VAC ~ 305VAC RATED POWER 96W 95.76W 95.76W 96W 96.12W 100VAC ~ 180VAC 70W 70W 70W 70W 70W RIPPLE & NOISE (max.) Note.3 0mVpp 250mVpp 250mVpp 300mVpp 350mVpp VOLTAGE ADJ. RANGE Adjustable for AType only (via the builtin potentiometer) 21.6 ~ 26.4V 32.4 ~ 39.6V 37.8 ~ 46.2V 43.2 ~ 52.8V 48.6 ~ 59.4V TOTAL HARMONIC DISTORTION MAX. No. of PSUs on 16A CIRCUIT BREAKER OVER CURRENT SHORT CIRCUIT 70~100W Constant Voltage Constant Current LED Driver NO LOAD / STANDBY POWER CONSUMPTION SAFETY STANDARDS DALI STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION 100 ~ 305VAC 142 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz PF 0.97/115VAC, PF 0.95/230VAC, PF 0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) THD< %(@load 50%/115VC; @load 60%/230VAC; @load 75%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION(THD) section) 1 ~ 2A ±2.0% 88% 89% 90% 90% 91% 1.1A / 115VAC 0.6A / 230VAC 0.5A/277VAC COLD START 60A(twidth=850μ s measured at 50% Ipeak) at 230VAC; Per NEMA 410 3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC <0.75mA / 277VAC No load power consumption <0.5W for Blank / A / Dx / D2Type Standby power consumption <0.5W for B / DAType 95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed 28 ~ 34V 41 ~ 48V 47 ~ 54V 54 ~ 62V 62 ~ 72V Shut down output voltage, repower on to recover Shut down output voltage, repower on to recover Tcase=40 ~ 90 (Please refer to OUTPUT LOAD vs TEMPERATURE section) Tcase=90 ~ 95% RH noncondensing 40 ~ 80, 10 ~ 95% RH ± 0.03%/ (0 ~ 60 ) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750 (type HL ), CSA C22.2 No. 250.1312; ENEC EN613471, EN61347213 independent, EN62384; GB19510.1, GB19510.14; IP65 or IP67 approved Compliance to IEC62386101, 102, 7 for DAType only I/PO/P:3.75KVAC I/PFG:2.0KVAC O/PFG:1.5KVAC I/PO/P, I/PFG, O/PFG:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015,EN6100032 Class C (@load 60%); EN6100033; GB17743, GB17625.1 978.2K hrs min. Telcordia SR332 (Bellcore) 282.9Khrs min. MILHDBK217F (25 ) 199* 63*35.5mm (L*W*H) 0.85kg; 16pcs/14.2kg/0.72CUFT 0.89 ~ 1.78A ±2.0% Compliance to EN6100042,3,4,5,6,8,11; EN61547, light industry level ( surge immunity LineEarth 6KV, LineLine 4KV)
Block Diagram PFC fosc : 50~1KHz PWM fosc : 60~130KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER O.L.P. Vo Vo O.T.P. O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT O.V.P. CASE GROUND DRIVING METHODS OF LED MODULE This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. 100 In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) 50 (min.) (A) Constant Voltage area (C) Hiccup Protection (B) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. 50 100 Io(%) Typical output current normalized by rated current (%) This characteristic applies to Blank/A/B/DX/D2Type, For DAType, the Constant Current area is 60%~100% Vo.
DIMMING OPERATION AC/N(Blue) AC/L(Brown) ELG100 DIM( Gray)* DIM(Black)** Vo(Blue) Vo(Brown) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 0 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100μA (typ.) Applying additive 0 ~ 10VDC Vo DO NOT connect "DIM to Vo" Additive Voltage Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage * DIM for BType DA for DAType PROG for D2Type * *DIM for BType DA for DAType PROG for D2Type Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 0% 0% 10% % 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: Vo Vo DIM DIM Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): Vo Vo DIM Additive PWM signal DIM DO NOT connect "DIM to Vo" Vo DIM DIM DO NOT connect "DIM to Vo" Additive Resistance Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%. 2. The output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle. Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 0% Short 10K/N K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance
DALI Interface (primary side; for DAType) Apply DALI signal between DA and DA. DALI protocol comprises 16 groups and 64 addresses. First step is fixed at 8% of output. Smart timer dimming function (for DxxType by User definition) MEAN WELL Smart timer dimming primarily provides the adaptive proportion dimming profile for the output constant current level to perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications. If other options may be needed, please contact MEAN WELL for details. Ex : D01Type: the profile recommended for residential lighting Set up for D01Type in Smart timer dimming software program: Dimming Level(%) TIME** LEVEL** T1 T2 06:00 07:00 100% 70% T3 11:00 50% T4 70% Operating Time(HH:MM) **: TIME mahes Operating Time in the diagram whereas LEVEL mahes Dimming Level. Example: If a residential lighting application adopts D01Type, when turning on the power supply at 6:00pm, for instance: [1] The power supply will swih to the constant current level at 100% starting from 6:00pm. [2] The power supply will swih to the constant current level at 70% in turn, starting from 0:00am, which is 06:00 after the power supply turns on. [3] The power supply will swih to the constant current level at 50% in turn, starting from 1:00am, which is 07:00 after the power supply turns on. [4] The power supply will swih to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The constant current level remains till 8:00am, which is 14:00 after the power supply turns on. Ex: D02Type: the profile recommended for street lighting Set up for D02Type in Smart timer dimming software program: Dimming Level(%) TIME** LEVEL** T1 01:00 50% T2 03:00 80% T3 T4 T5 8:00 11:00 100% 60% 80% Operating Time(HH:MM) **: TIME mahes Operating Time in the diagram whereas LEVEL mahes Dimming Level. Example: If a street lighting application adopts D02Type, when turning on the power supply at 5:00pm, for instance: [1] The power supply will swih to the constant current level at 50% starting from 5:00pm. [2] The power supply will swih to the constant current level at 80% in turn, starting from 6:00pm, which is 01:00 after the power supply turns on. [3] The power supply will swih to the constant current level at 100% in turn, starting from 8:00pm, which is 03:00 after the power supply turns on. [4] The power supply will swih to the constant current level at 60% in turn, starting from 1:00am, which is 08:00 after the power supply turns on. [5] The power supply will swih to the constant current level at 80% in turn, starting from 4:00am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30am, which is 14:00 after the power supply turns on.
Ex: D03Type: the profile recommended for tunnel lighting Set up for D03Type in Smart timer dimming software program: Dimming Level(%) T1 T2 T3 TIME** 01:30 11:00 LEVEL** 70% 100% 70% Operating Time(HH:MM) **: TIME mahes Operating Time in the diagram whereas LEVEL mahes Dimming Level. Example: If a tunnel lighting application adopts D03Type, when turning on the power supply at 4:30pm, for instance: [1] The power supply will swih to the constant current level at 70% starting from 4:30pm. [2] The power supply will swih to the constant current level at 100% in turn, starting from 6:00pm, which is 01:30 after the power supply turns on. [3] The power supply will swih to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30am, which is 14:00 after the power supply turns on.
OUTPUT LOAD vs TEMPERATURE 100 100 80 60 230VAC input only 80 60 230VAC input only LOAD (%) 40 LOAD (%) 40 40 25 10 0 15 30 50 60 70 (HORIZONTAL) 40 25 0 10 30 50 70 85 90 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC 100 Tcase at 80 Constant Current Mode 90 1 LOAD (%) 80 70 60 50 40 PF 0.98 0.96 0.94 0.92 0.9 0.88 277V(100W) 230V(100W) 115V(80W) (70W) 100 1 140 160 180 0 240 250 260 270 280 305 INPUT VOLTAGE (V) 60Hz Derating is needed under low input voltage. 0.86 50% 60% 70% 80% 90% 100% LOAD TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD possess superior working efficiency that up to 91% can be reached in field applications. 54V Model, Tcase at 80 54V Model, Tcase at 80 21% 19% 94 17% 92 THD 15% 13% 11% 9% 7% 5% 3% 0.5 0.6 0.7 0.8 0.9 1 277VAC(100W) 230VAC(100W) 115VAC(80W) (70W) EFFICIENCY(%) 90 88 86 84 82 80 50% 60% 70% 80% 90% 100% 277V(100W) 230V(100W) 115V(80W) (70W) LOAD LOAD
LIFE TIME 1 100 80 LIFETIME(Kh) 60 40 0 30 40 50 60 70 80 90 Tc a s e ( )
Mechanical Specification BlankType CASE NO.: 244A Unit:mm 300± 199 188 175 300± AC/N(Blue) AC/L(Brown) 63 45.8 105 Vo(Blue) Vo(Brown) 4ψ4.5 : Max. Case Temperature 35 35.5 AType 300± 199 188 175 300± AC/N(Blue) AC/L(Brown) 63 45.8 105 : Max. Case Temperature 35 35.5 Vo(Blue) Vo(Brown) 4ψ4.5 21.5 14 33
B/ DA/D2Type 300± 199 188 175 300± AC/N(Blue) AC/L(Brown) 63 45.8 4ψ4.5 105 : Max. Case Temperature DIM( Gray)* DIM(Black)** Vo(Blue) Vo(Brown) 35 35.5 * DIM for BType DA for DAType PROG for D2Type * *DIM for BType DA for DAType PROG for D2Type Note1: Please connect the case to FG for the complete EMC deliverance. Note2: Please contact MEAN WELL for input wiring option with FG. INSTALLATION MANUAL Please refer to : http://www.meanwell.com/manual.html