John Lewis Double King Size Rouen Storage Bed Stock code: 80/4404 Stock code: 80/4405 Thank you for purchasing this Rouen Storage Bed. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. For product support or spare parts please call the John Lewis Helpline; T: 044 684 E: mail@fwgroup-uk.com PRE-ASSEMBLY PREPARATION Please ensure instructions are read in full before attempting to assemble this product. Necessary Tools Please check the pack contents before attempting to assemble this product. A full checklist of components is given in this leaflet. If any components are missing, please contact the John Lewis Helpline. This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN LIFTING to avoid personal injury and (or) damage to the product. This product takes approximately 0 MINUTES to assemble with PEOPLE. Do not use power tools to assemble. The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN. Read this leaflet in full before commencing assembly. If you require any additional information or have any issues with this product please call the John Lewis Helpline on 044 684 or email mail@fwgroup-uk.com /8
Fittings and parts checklist A M4 Allen Key x pcs H M6 X 40mm Bolt x 8 pcs B M5 Allen Key x pcs I Screw 4 x 50mm x 4pcs C Centre Plastic Caps x 5 pcs J Screw.5 x 0mm x 4pcs D Side Plastic Caps x 0 pcs K Nut M8 x pcs E Spring Washer M8 x 0 pcs L Spanner M x pcs F M8 X 6mm Bolt x 8 pcs M Screw 4 x 8mm x 8pcs G M6 X 5mm Bolt x 6 pcs Headboard x Footboard x Side Rails x 4 5 6 Slats x 0 Centre Rail x Wooden Legs x 4 8 Bottom Supports x Centre Support x Drawer Sides x 4 0 Drawer Backs x Drawer Fronts x Drawer Bottoms x 4 5 6 Drawer Panels x Drawer Supports x 6 Metal plates x Metal Stopper x 4 /8
Step One Place metal bracket on Side Rails () over pre-inserted bolts in Headboard () and Footboard () and hand-tighten to loosely secure parts together. Do not tighten bolts with M5 Allen Key (B) until you have inserted the Centre Rail in Step Four. LOOSELY SECURE PARTS TOGETHER IN ORDER FOR CENTRE RAIL TO FIT IN STEP FOUR BRACKET SIDE RAIL BRACKET SIDE RAIL Step Two Attach Spring Washer M8 (E) and JCBC M8 x 6mm Bolts (F) into the metal fixings onto both Bottom Supports () (only for the top side). Insert the Bottom Supports () inside the bed frame as shown in step. Next, attach the Spring Washer M8 (E) and JCBC M8 x 6mm Bolts (F) into the bottom side of metal fixing on the bottom supports. Loosely tighten the bolts using M5 Allen Key (B). STEP Spring Washer M8 (E) LOOSELY SECURE PARTS TOGETHER IN ORDER FOR CENTRE RAIL TO FIT IN STEP FOUR M8 x 6mm Bolt (F) STEP Fig B. E. F. M5 Allen Key (B) M5 Allen Key x Spring Washer M8 x 8 M8 x 6mm Bolt x 8 /8
Step Three Attach Centre Support (8) to Bottom Supports () and secure into place using Screws 4 x 50mm (I) as shown in the diagram below. 8 x Screw 4 x 50mm (I) 8 I Screw 4 x 50mm (I) Screw 4 x 50mm x 4 Cross head Screw Driver Step Four Insert Centre Rail (5) into the brackets on the Headboard () and Footboard (). Push down fully and secure in place using M6 x 5mm Bolts (G). Tighten using M4 Allen Key (A). You can now tighten the bolts with M5 Allen Key (B) at the Side Rails from Step One so all fastenings are now tightened. STEP M6 x 5mm (G) AFTER INSERTING CENTRE RAIL, TIGHTEN ALL FIXINGS FULLY INCLUDING BOLTS AT SIDE RAILS (FROM STEP ONE) M4 Allen Key (A) STEP 5 A. G. M4 Allen Key x M6 x 5mm Bolt x 4/8
Step Five Insert the Front Legs (6)x into the pre-drilled holes on the underside of the Headboard () and twist to secure, as shown in the diagram below. For Headboard Only 6 6. Step Six Legs x Attach the Metal Plate (5) to the bottom of the Footboard () using Bolts M6 X 5mm (G)x. Do not tighten the bolts until you make adjustment for the screw hole at the Side Rail (). Insert Wooden Leg (6) into the bottom of the Metal Plate (5) using Spring Washer M8 (E) and Nut M8 (K). Hold the Nut M8 (K) using Spanner M (L) and twist the Wooden Leg (6) to secure in place. Repeat for other leg. For Footboard Only M6 x 5mm (G) M4 (A) STEP M6 x 5mm (G) Yellow sticker face down AFTER INSERTING BOLT M6 x 5MM, MAKE ADJUSTMENT FOR SCREW HOLE, THEN INSERT THE SCREW.5 X 0MM. TIGHTEN THE BOLT M6 x 5MM FIXINGS FULLY..5 x 0mm (J) TWIST WOODEN LEG ONLY WITHOUT MOVING THE M8 NUT, SPRING WASHER AND SPANNER STEP M6 x 5mm (G) M4 (A) M6 x 5mm (G) Nut M8 (K) Spring Washer M8 (E) 5 6 Twist the wooden leg.5 x 0mm (J) Spanner M (L) x E. 6. 5. L. K. J. G. A. Spring Washer M8 () Legs () Metal plates () Spanner M () Nut M8 () Screw.5 x 0mm () M6 X 5mm Bolt (4) M4 Allen Key () 5/8
Step Seven Attach Metal Stopper (6) to the Bottom Support () using screw 4 x 8mm (M). 6 4x M. 6. Screw 4 x 8 (8) Metal Stopper x 4 Step Eight With the curved side facing upwards, insert Slats (4) into a Centre Plastic Cap (C) followed by a Side Plastic Cap (D) onto the other end of both slats. Use your palms to push down the centre plastic caps into the centre rail followed by the side plastic caps into the side rail as shown in diagram below. 4 Step C 4 x5 4. D 4 Step C. Slats (0pcs) C 4 D 4 x0 Centre Plastic Caps (5 pcs) D. D Side Plastic Caps (0 pcs) 6/8
Step Nine To construct the drawers, fix Drawer Back (0) with one end of each Drawer Support (4) using Screws.5 x 0mm (J) as shown in Fig., then fix the Drawer Sides () to the Drawer Back (0). Next, insert Drawer Bottom () and then fix Drawer Front () using Screws.5 x 0mm (J) as shown in Fig.. Finally, secure the other end of the Drawer Supports (4) to the other side of the drawer and tighten using a cross head screw driver. Fig. Fig. Fig. 0 0 4 4 4 4 (x) (x) (x) J..5 x 0mm(40) Cross Head Screw Driver Step Ten Attach Drawer Panel () to drawer and tighten together using M6 x 40mm Bolt (H). Tighten with M4 Allen Key (A). Slide drawers into both sides of the bed frame. The bed is now ready for use. A. H. M4 Allen Key x M6 x 40mm x 8 /8 x
Care and Maintenance This Rouen Storage Bed should be cleaned using a soft damp cloth and dried immediately. Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently damage the surface. Do not use detergents and do not rub as this can cause permanent damage. Always protect your bed from direct sunlight as this may accelerate the natural ongoing discolouration process. Bolts holding together the bed frame should be tightened regularly. Please retain this information leaflet for future reference. This product complies with BS EN 5:8. Safety Instructions Never drag furniture when moving it. Always lift it. Periodically check all fixings to ensure none have come loose and re-tighten where necessary. Please take care when handling or moving the furniture as careless handling may cause damage or injury. Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent adult. No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture. During assembly, children should be kept away from the product due to possible risk of injury. Do not use this item if any components are missing or damaged. It is recommended that care is taken when moving heavy objects to a new location to avoid personal injury or damage to the furniture. Please be careful to retain all fittings when doing this. If you require any additional information or have any issues with this product please call the John Lewis Helpline on 044 684 or email mail@fwgroup-uk.com John Lewis Partnership Victoria Street, London, SWE 5NN. www.johnlewis.com 8/8