MEDIUM VOLTAGE TERMINATIONS CATALOGUE 01
NEXANS NETWORK SOLUTIONS DIV. EUROMOLD COMPANY PRESENTATION EUROMOLD Euromold is the leading European specialised designer, manufacturer and distributor of prefabricated cable accessories for medium voltage energy distribution. Euromold provides a complete range of accessories for underground cables: premoulded EPDM rubber connectors for cables and epoxy bushings for transformers and switchgear, as well as a large range of coldshrinkable terminations and joints from 1 to kv. Euromold is also the manufacturer of electrical components for the high voltage accessories of the Nexans group. International standards All our products meet the International standards like CENELEC HD 9.1, CENELEC EN 50180, IEC 01, IEC 050- or country specifications. Official certificates, CESI, KEMA, ATEX prove the conformity of our products. Long duration tests of existing or new products are continuously performed in our test fields. Laboratory accreditation Since June 000, Euromold s independent ELAB laboratory obtained the BELAC accreditation no.1-test conform with the European standards for laboratories ISO 105 for electrical testing of low and medium voltage cable accessories according to the international standards EN 509, IEC 050-, IEC 1 and HD 9. ISO 9001 Certificate Since 199, Euromold s commitment to quality is demonstrated by its ISO 9001 certification. While every care is taken to ensure that the information contained in this publication is correct, no legal responsibility can be accepted for any inaccuracy. Nexans Network Solutions N.V. - Div. Euromold reserves the right to alter or modify the characteristics of its products described in this catalogue as standards and technology evolve.
10/01
TERMINATIONS TABLE OF CONTENTS ITK - cold-shrinkable indoor termination OTK - cold-shrinkable outdoor termination AIN - slip-on indoor termination AFN - slip-on outdoor termination SREI - single core XLPE indoor termination SREF - single core XLPE outdoor termination SRDI - three core XLPE indoor termination SRDF - three core XLPE outdoor termination SPDI - three core PILC indoor termination SPDF - three core PILC outdoor termination MONOi - heat-shrinkable mv indoor termination MONOe - heat-shrinkable mv outdoor termination 15TS - universal bushing boot FB1 - flexible bushing boot RAB/SB - heat-shrinkable bushing boot SE - XLPE solderless earth connection CK - PILC solderless earth connection HSGK - top hat gland kit RAE KITS - remote armour earthing XCK-HSS - Multi core heat-shrink breakout kit
ITK COLD-SHRINKABLE INDOOR TERMINATION A kit of terminations for use indoors in controlled environmental conditions and subject to light condensation. To connect polymeric insulated cable to equipment. 1 DESIGN Indoor termination comprising: 1. Cable lug (not included in the standard kit).. Water sealing mastic.. Silicone tube.. Stress control mastic. 5. Conductive EPDM ring. L /10 (1) kv.5/11 (1) kv 8./15 (1.5) kv 1/0 () kv 1./ () kv Up to kv SPECIFICATIONS AND STANDARDS Meets the requirements of CENELEC HD 9.1. 5 Termination type Voltage Um (kv) Strike distance L (mm) Diameter over core insulation (mm) Conductor sizes (mm ) min max min max ITK 1 ITK 1 ITK ITK 1 1 0 00 0 00 1 0 1 0 50 50 50 00 5 00 00 1000 0 800 10/01
KIT CONTENTS The complete ITK termination kit comprises the following components: The kit also comprises water sealing mastic and installation instructions. = x ITK 1 or ITK termination kit x Factory pre-assembled silicone tubes comprising stress relief and sealing mastic. = x ITK 1 or ITK termination kit x Factory pre-assembled silicone tubes comprising stress relief and sealing mastic. ORDERING INSTRUCTIONS Select the part number corresponding to both the system voltage and the cable insulation diameter in mm. EXAMPLE: The copper wire screened cable is 1 kv, 150 mm stranded aluminium. The diameter over core insulation is. mm. Order a x ITK 1 termination kit. Ordering part number x ITK 1 x ITK 1 x ITK x ITK Voltage Um (kv) 1 1 Diameter over core insulation (mm) Conductor sizes (mm ) min max min max 1 50 00 0 50 00 1000 1 5 0 0 50 00 800 mm max 0 mm min 110 mm max A All commercialised European standard cable lugs can be used. Cable lugs should be within the dimensions specified (not applicable for ITK 1 and ITK ). For use with copper wire screened cables. No earthing device is necessary. For use with copper tape screened cables. Also order a Kit MT. For use with Alupe or C - cables. Please contact our representative. For use with three-core cables: see T-ITK. If the cable lug barrel diameter (A) is less than 0 mm: order a rubber adapting sleeve. Can be supplied with all common types of cable lugs. 5
A A A OTK COLD-SHRINKABLE OUTDOOR TERMINATION A kit of terminations for use outdoors and exposed to prolonged sunshine and other weather conditions. To connect polymeric insulated cable to equipment and for the outdoor terminating on to overhead lines or busbars. DESIGN Outdoor termination comprising: 1. Cable lug (not included in the standard kit).. Water sealing mastic.. Sheds which can be installed upwards or down.. Silicone tube with sheds. 5. Silicone tube.. Stress control mastic.. Conductive EPDM ring. 1 L 1 L 1 L /10 (1) kv.5/11 (1) kv 8./15 (1.5) kv 1/0 () kv 1./ () kv Up to kv 5 5 SPECIFICATIONS AND STANDARDS Meets the requirements of CENELEC HD 9.1. B B B Fig. 1 Fig. Fig. Voltage Termination Um type (kv) OTK 1 OTK 1 OTK OTK 1 1 Creepage distance A-B (mm) 0 890 00 890 Strike Diameter over distance core insulation Number L (mm) (mm) of sheds 00 50 00 50 Conductor sizes (mm ) min max min max 1 50 00 0 50 500 1000 19 5 50 0 0 50 00 0 Fig. no. 1 10/01
KIT CONTENTS The complete OTK termination kit comprises the following components: The kit also comprises water sealing mastic and installation instructions. x Factory pre-assembled silicone tubes comprising stress relief and sealing mastic. x OTK 1 termination kit x Factory pre-assembled silicone tubes comprising stress relief and sealing mastic. x Silicone tube with 5 sheds x OTK termination kit x Factory pre-assembled silicone tubes comprising stress relief and sealing mastic. x Silicone tube with sheds x OTK 1 or x OTK termination kit ORDERING INSTRUCTIONS Select the part number corresponding to both the system voltage and the cable insulation diameter in mm. EXAMPLE: The copper wire screened cable is kv, 150 mm stranded aluminium. The diameter over core insulation is. mm. Order a x OTK termination kit. Ordering part number x OTK 1 x OTK 1 x OTK x OTK Voltage Um (kv) 1 1 Diameter over core insulation (mm) Conductor sizes (mm ) min max min max 1 50 00 0 50 500 1000 19 50 0 0 50 00 800 A All commercialised European standard cable lugs can be used. Cable lugs should be within the dimensions specified (not applicable for OTK 1 and OTK ). For use with copper wire screened cables. No earthing device is necessary. For use with copper tape screened cables. Also order a Kit MT. If the cable lug barrel diameter (A) is less than 0 mm: order a rubber adapting sleeve. For use with Alupe or C - cables. Please contact our representative. For use with three-core cables: see T-OTK. Can be supplied with all common types of cable lugs.
AIN SLIP-ON INDOOR TERMINATION A kit of terminations for use indoors in controlled environmental conditions and subject to light condensation. Provides a simple and quick method of stress relieving on screened polymeric cables. DESIGN Indoor termination comprising: 1. Cable lug (not included in the standard kit).. High flexibility silicone rubber housing, allowing larger tolerances on cable insulation diameters, with integrated conductive rubber insert, providing stress relief.. Earthing lug (not included in the standard kit). 1 /10 (1) kv.5/11 (1) kv 8./15 (1.5) kv 1/0 () kv 1./ () kv 18/0 () kv 0.8/ () kv Up to kv SPECIFICATIONS AND STANDARDS Meets the requirements of CENELEC HD 9.1 and IEC 050-. Termination type Voltage Um (kv) Conductor sizes (mm ) min max AIN 10 AIN 0 AIN 0 AIN 1 5 5 50 150 100 100 1000 1000 10/01 8
KIT CONTENTS A kit always comprises termination housings, installation instructions, special lubricant, wiper, adhesive tape, field control mastic,... Cable lugs and earthing lugs are not included in the standard kit, but can be ordered separately. ORDERING INSTRUCTIONS Select the part number corresponding to both the system voltage and the cable dimensions in mm. Voltage Um (kv) 1 Conductor sizes (mm ) Diameter over core insulation (mm) min max min max 5 95 1. 1.0 10 0 19.0 8.5 00 500.0.0 0 800.0.0 1000 9.0 50.0 100.0 58.0 Number of sheds L (mm) 150 150 150 5 Dia. D (mm) 0 8 98 98 Ordering part number x AIN 10-1 x AIN 10- x AIN 10- x AIN 0- x AIN -5 x AIN - 5 95 00 00 0 1000 0 0 500 0 800 100 18.0.5 1.0.0 9.0.0.5.0 1.0.0 50.0 58.0 5 5 5 5 5 8 8 98 98 x AIN 0-1 x AIN 0- x AIN 0- x AIN 0- x AIN -5 x AIN - 50 95 0 00 0 0 0 00 0 1000.5.0.0 9.0.0 9.0 8.0.0 50.0 58.0 00 00 00 81 98 98 x AIN 0-1 x AIN 0- x AIN 0- x AIN -5 x AIN - 150 00 0 00 0 1000 1.5 9.0.0 1.0 50.0 58.0 98 98 98 x AIN - x AIN -5 x AIN - EXAMPLE: A set of indoor terminations for a kv - 0 mm stranded aluminium cable with copper wire screen without cable lugs. The diameter over core insulation is 0. mm. Order a x AIN 0- termination kit. For use with copper wire screened cables. No earthing device is necessary. For use with copper tape screened cables. Order: -/MT. For use with three-core cables. Please contact our representative. For use with other cable types. Please contact our representative. Can be supplied with all common types of cable lugs. No heating or flame is required. 9
AFN SLIP-ON OUTDOOR TERMINATION A kit of terminations for use outdoors and exposed to prolonged sunshine and other weather conditions. To connect polymeric insulated cable to equipment and for the outdoor terminating on to overhead lines or busbars. DESIGN Outdoor termination comprising: 1. Cable lug (not included in the standard kit).. Water sealing silicone sleeve.. Silicone housing with sheds and integrated conductive silicone rubber insert providing stress relief for the cable.. Water sealing mastic. 5. Earthing clamp.. Earthing lug (not included in the standard kit). 1 /10 (1) kv.5/11 (1) kv 8./15 (1.5) kv 1/0 () kv 1./ () kv 18/0 () kv 0.8/ () kv Up to kv SPECIFICATIONS AND STANDARDS Meets the requirements of CENELEC HD 9.1 and IEC 050-. 5 Termination type Voltage Um (kv) Conductor sizes (mm ) min max AFN 10 AFN 0 AFN 0 AFN 1 5 5 50 0 100 100 1000 1000 10/01 10
KIT CONTENTS A kit always comprises termination housings, water sealing sleeve, the installation instructions, special lubricant, wiper, earthing clamp, water sealing mastic, adhesive tape, field control mastic,... Cable lugs and earthing lugs are not included in the standard kit, but can be ordered separately. ORDERING INSTRUCTIONS Select the part number corresponding to both the system voltage and the cable dimensions in mm. Voltage Um (kv) 1 Conductor Diameter over L sizes core insulation Number (mm) (mm ) (mm) of sheds (max) min max min max 5 10 00 0 95 0 500 800 1. 19.0.0.0 1.0 8.5.0.0 1000 100 9.0.0 50.0 58.0 5 95 00 00 0 1000 0 0 500 0 800 100 18.0.5 1.0.0 9.0.0.5.0 1.0.0 50.0 58.0 50 0.5 9.0 95 0.0 8.0 0 00.0.0 00 0 9.0 50.0 0 1000.0 58.0 0 10 8.0.0 150 00 1.5 1.0 00 0 9.0 50.0 0 1000.0 58.0 10 10 10 0 0 0 0 0 00 00 00 Creepage Dia. D Ordering distance (mm) part number (mm) 90 9 x AFN 10-1 9 5 x AFN 10-105 0 x AFN 10-118 x AFN 0-1 55 x AFN -5 1 55 x AFN - 100 80 x AFN 0-1 11 99 x AFN 0-118 x AFN 0-118 x AFN 0-1 55 x AFN -5 1 55 x AFN - 115 95 x AFN 0-1 115 9 x AFN 0-1 18 x AFN 0-1 55 x AFN -5 1 55 x AFN - 1 55 x AFN - 1 55 x AFN - 1 55 x AFN -5 1 55 x AFN - For use in heavy polluted areas (terminations with an increased creepage length) 0 150 00 0 10 00 0 1000 8.0 1.5 9.0.0.0 1.0 50.0 58.0 11 11 11 11 55 55 55 55 1 1 1 1 109 109 109 109 x AFNP - x AFNP - x AFNP -5 x AFNP - EXAMPLE: A set of outdoor terminations for a kv - 0 mm stranded aluminium cable with copper wire screen without cable lugs. The diameter over core insulation is 0. mm. Order a x AFN 0- termination kit. For use with copper wire screened cables. No earthing device is necessary. For use with copper tape screened cables. Order: -/MT. For use with three-core cables. Please contact our representative. For use with other cable types. Please contact our representative. Can be supplied with all common types of cable lugs. No heating or flame is required. 11
SREI HEAT-SHRINKABLE SINGLE CORE XLPE INDOOR TERMINATION A set of three heat-shrinkable terminations for polymeric cables, widely used by power utilities and in industrial applications. For use indoor in controlled environmental conditions. DESIGN 1. Cable lug (supplied on request).. Water sealing mastic.. Anti-tracking heat-shrinkable tube.. Stress control heat-shrinkable tube. 5. Stress control mastic.. Anti-tracking sheds (when required). 1 1 /10 (1) kv.5/11 (1) kv 8./15 (1.5) kv 1/0 () kv 1./ () kv 18/0 () kv 19/ () kv Up to kv SPECIFICATIONS AND STANDARDS Meets the requirements of CENELEC HD 9.1 and IEC 050-. ORDERING INSTRUCTIONS 5 5 Select the part number and add both system voltage and conductor size range. Example part number: SREI 1/10-0 Termination type Voltage class (Um) 1 kv (1 &) kv kv SREI Cable cross section (mm²) 5-95 10-0 0-500 00-0 5-0 95-185 0-00 00-0 50-95 10-0 0-500 00-0 For use with other sizes and cable types. Please contact our representative. 10/01 1
HEAT-SHRINKABLE SINGLE CORE XLPE OUTDOOR TERMINATION SREF A set of three heat-shrinkable terminations for polymeric cables, widely used by power utilities and in industrial applications. For use outdoors and exposed to prolonged sunshine and other weather conditions. DESIGN 1. Cable lug (supplied on request).. Water sealing mastic.. Anti-tracking heat-shrinkable tube.. Stress control heat-shrinkable tube. 5. Stress control mastic.. Anti-tracking sheds. 1 /10 (1) kv.5/11 (1) kv 8./15 (1.5) kv 1/0 () kv 1./ () kv 18/0 () kv 19/ () kv Up to kv SPECIFICATIONS AND STANDARDS Meets the requirements of CENELEC HD 9.1 and IEC 050-. ORDERING INSTRUCTIONS Select the part number and add both system voltage and conductor size range. Example part number: SREF 1/10-0 5 Termination type Voltage class (Um) 1 kv (1 &) kv kv SREF Cable cross section (mm²) 5-95 10-0 0-500 00-0 5-0 95-185 0-00 00-0 50-95 10-0 0-500 00-0 For use with other sizes and cable types. Please contact our representative.
SRDI HEAT-SHRINKABLE THREE CORE XLPE INDOOR TERMINATION Heat-shrinkable terminations for three core polymeric cables, widely used by power utilities and in industrial applications. For use indoor in controlled environmental conditions. DESIGN 1. Cable lug (supplied on request).. Water sealing mastic.. Anti-tracking heat-shrinkable tube.. Anti-tracking sheds (when required). 5. Stress control heat-shrinkable tube.. Stress control mastic.. Break-out. SPECIFICATIONS AND STANDARDS Meets the requirements of CENELEC HD 9.1 and IEC 050-. ORDERING INSTRUCTIONS Select the part number and add both system voltage and conductor size range. Example part number: SRDI 1/10-0 1 5 /10 (1) kv.5/11 (1) kv 8./15 (1.5) kv 1/0 () kv 1./ () kv 18/0 () kv 19/ () kv Up to kv Termination type Voltage class (Um) 1 kv (1 &) kv kv SRDI Cable cross section (mm²) 5-95 10-0 0-500 5-0 95-185 0-00 50-10 150-0 0-00 For use with other sizes and cable types. Please contact our representative. 10/01 1
HEAT-SHRINKABLE THREE CORE XLPE OUTDOOR TERMINATION SRDF Heat-shrinkable terminations for three core polymeric cables, widely used by power utilities and in industrial applications. For use outdoors and exposed to prolonged sunshine and other weather conditions. DESIGN 1. Cable lug (supplied on request).. Water sealing mastic.. Anti-tracking heat-shrinkable tube.. Anti-tracking sheds. 5. Stress control heat-shrinkable tube.. Stress control mastic.. Break-out. 1 /10 (1) kv.5/11 (1) kv 8./15 (1.5) kv 1/0 () kv 1./ () kv 18/0 () kv 19/ () kv Up to kv SPECIFICATIONS AND STANDARDS Meets the requirements of CENELEC HD 9.1 and IEC 050-. ORDERING INSTRUCTIONS Select the part number and add both system voltage and conductor size range. Example part number: SRDF 1/10-0 5 Termination type Voltage class (Um) 1 kv (1 &) kv kv SRDF Cable cross section (mm²) 5-95 10-0 0-500 5-0 95-185 0-00 50-10 150-0 0-00 For use with other sizes and cable types. Please contact our representative.
SPDI HEAT-SHRINKABLE THREE CORE PILC/PICAS INDOOR TERMINATION Heat-shrinkable terminations for three core PILC/PICAS cables, used by power utilities and in industrial applications. For use indoor in controlled environmental conditions. DESIGN 1. Cable lug (supplied on request).. Water sealing mastic.. Anti-tracking heat-shrinkable tube.. Anti-tracking sheds (when required). 5. Stress control heat-shrinkable tube.. Stress control mastic.. Break-out. 8. Barrier tube. SPECIFICATIONS AND STANDARDS Meets the requirements of CENELEC HD 9.1 and IEC 050-. ORDERING INSTRUCTIONS Select the part number and add both system voltage and conductor size range. Example part number: SPDI 1/95-150 1 8 5 /10 (1) kv.5/11 (1) kv Up to 1 kv Termination type Voltage class (Um) Cable cross section (mm²) SPDI 1/1-5 SPDI 1/5-0 SPDI 1/95-150 SPDI 1/185-500 1 kv 1-5 5-0 95-150 185-500 For use with other sizes and cable types. Please contact our representative. 10/01 1
HEAT-SHRINKABLE THREE PILC/PICAS OUTDOOR TERMINATION SPDF Heat-shrinkable terminations for three core PILC/PICAS cables, widely used by power utilities and in industrial applications. For use outdoors and exposed to prolonged sunshine and other weather conditions. DESIGN 1. Cable lug (supplied on request).. Water sealing mastic.. Anti-tracking heat-shrinkable tube.. Anti-tracking sheds. 5. Stress control heat-shrinkable tube.. Stress control mastic.. Break-out. 8. Oil barrier tube. 9. Anti-tracking tri-shed. SPECIFICATIONS AND STANDARDS Meets the requirements of CENELEC HD 9.1 and IEC 050-. ORDERING INSTRUCTIONS Select the part number and add both system voltage and conductor size range. Example part number: SPDF 1/95-150 1 8 5 9 /10 (1) kv.5/11 (1) kv Up to 1 kv Termination type Voltage class (Um) Cable cross section (mm²) SPDF 1/1-5 SPDF 1/5-0 SPDF 1/95-150 SPDF 1/185-500 1 kv 1-5 5-0 95-150 185-500 For use with other sizes and cable types. Please contact our representative.
MONOi HEAT-SHRINKABLE MV INDOOR TERMINATION The MONOi terminations are a single component solution, for single core polymeric cables. TECHNICAL DESCRIPTION The MONOi indoor terminations are designed for max system voltages of kv, for compact switchgears as well as for installations where space is limited. Easy, quick to install, reducing installation time and errors. The kit consists of a stress control mastic strip, a co extruded dual wall tube and red anti-tracking sealing mastic. Add on kit for armoured cables are available separately. Each MONOi termination kit contains material to allow for phase installation. Type tested acc.: Cenelec HD 9.1 S IEC 050- Up to 19/ () kv voltage Um kv type application range (mm ) L (mm) 1 x1monoi 1.95 5 95 0 1 x1monoi 1.0 0 0 0 1 x1monoi 1.00 185 00 80 1 x1monoi 1.0 00 0 10 xmonoi 1.95 5 95 0 xmonoi 1.0 0 0 0 xmonoi 1.00 185 00 0 xmonoi 1.0 00 0 0 xmonoi 1.95 5 95 0 xmonoi 1.0 0 0 0 xmonoi 1.00 185 00 0 xmonoi 1.0 00 0 0 L For cables with AL foil screen/ vapor screen please contact our sales office. Please add the letter A at the end of the product code for cables with Cu tape screen. Earth kit included for cables with wire screens. For other cable types please contact our sales office. Trifurcating kits TK available separately. Please see available sizes of specific catalogue page. Various earth connection design solutions exist for armouring. For exact details contact our sales office. Design accommodates various lug types. Various earth connection kits are available for screen connection. For exact details contact our sales office. 10/01 18
HEAT-SHRINKABLE MV OUTDOOR TERMINATIONS MONOe Type tested acc.: Cenelec HD 9.1 S IEC 050- Up to 19/ () kv The MONOe terminations are a single component solution, for single core polymeric cables. TECHNICAL DESCRIPTION The MONOe outdoor terminations are designed for max system voltages of kv. Easy, quick to install, reducing installation time and errors. The kit consists of a stress control mastic strip, a co extruded dual wall tube, red anti-tracking sealing mastic and anti-tracking rain sheds. Add on kit for armoured cables are available separately. Each MONOe termination kit contains material to allow for phase installation. voltage Um kv type application range (mm ) L (mm) L 1 x1monoe 1.95 5 95 90 1 x1monoe 1.0 0 0 90 1 x1monoe 1.00 185 00 10 1 x1monoe 1.0 00 0 0 xmonoe 1.95 5 95 10 xmonoe 1.0 0 0 10 xmonoe 1.00 185 00 0 xmonoe 1.0 00 0 90 xmonoe 1.95 5 95 0 xmonoe 1.0 0 0 0 xmonoe 1.00 185 00 500 xmonoe 1.0 00 0 50 Designed for outdoor application. For cables with AL foil screen/ vapor screen please contact our sales office. Please add the letter A at the end of the product code for cables with Cu tape screen. Earth kit included for cables with wire screens. For other cable types please contact our sales office. Trifurcating kits TK available separately. Please see available sizes of specific catalogue page. Various earth connection design solutions exist for armouring. For exact details contact our sales office. Design accommodates various lug types. Various earth connection kits are available for screen connection. For exact details contact our sales office.
15TS-NSS UNIVERSAL BUSHING BOOT This universal bushing boot is manufactured from nontracking EPDM rubber and is designed to mate with all types of cold or heat-shrinkable terminations (without sheds). The bushing part fits interface diameters between 0 and 0 mm. The system is separable and allows easy removal for testing. This boot is suitable for all angles between 90 and 180. KIT CONTENTS The x 15TS-NSS kit comprises universal bushing boots, silicone grease and installation instructions. /10 (1) kv.5/11 (1) kv 8./15 (1.5) kv Up to 1.5 kv CLEARANCES This is an unscreened boot and therefore not safe to touch when energised. When used in a metal enclosed cable box, these minimum clearances must be respected. Bushing boot type Voltage Um (kv) Conductor sizes (mm Diameter D over ) termination (mm) min max min max 15TS-NSS 1.5 max 5 0 0 50 In mm. 10/01 0
FLEXIBLE BUSHING BOOT FB1 Bushing insulating elastomeric boots are used to insulate the bushing in switchgear and transformer cable termination boxes up to 1.5 kv especially where the clearances between phase to phase and phase to earth is less than the normal air clearance. These boots provide protection against flash over in the event of high humidity and surge impulse. The boots are made from highly insulating flexible and weather resistant elastomeric material. FB1 insulating boots are quick and easy to install. The boots can be removed easily for convenient access to the bushing connection for testing purposes. After testing the boot can be reinstalled easily without using additional material or tooling. KIT CONTENTS The FB1 kit comprises of flexible bushing boots and tubes of grease. /10 (1) kv.5/11 (1) kv 8./15 (1.5) kv CLEARANCES This is an unscreened boot and therefore not safe to touch when energised. ADVANTAGES High performance flexible insulation material with excellent tracking and erosion resistance. Quick and easy to remove and reinstall. Unlimited shelf life. Termination can be energised immediately after installation. TECHNICAL SPECIFICATION Basic impulse level: 95 kv Bushing diameter: 0-5 mm Cable sizes: 5-00 mm² Bushing boot type Voltage Um (kv) Description Diameter D over termination (mm) min. max. FB1 1.5 max. Flexible boot 5 00
RAB/SB HEAT-SHRINKABLE BUSHING BOOT Heat-shrinkable bushing boots are used to increase the creepage distance between the live metal and surrounding metal work and neighbouring phases. KIT CONTENTS The RAB/SB kit comprises heat-shrinkable bushing boots and mastic. /10 (1) kv.5/11 (1) kv 8./15 (1.5) kv Up to 1.5 kv CLEARANCES This is an unscreened boot and therefore not safe to touch when energised. Bushing boot type Voltage Um (kv) Description Conductor sizes (mm ) min. max. RAB 1 RAB RABS1 RABS SB 1 SB 1.5 max. 1.5 max. 1.5 max. 1.5 max. 1.5 max. 1.5 max. right angle right angle right angle short right angle short straight straight 1 10 1 10 1 10 95 00 95 00 95 00 10/01
XLPE SOLDERLESS EARTH CONNECTION INDOOR SE Required to effectively earth the copper tape screen of polymeric (XLPE & EPR) insulated cables without soldering. Supplied in sets of three. Part number -core kit Voltage class (Um). kv 1 kv (1 &) kv kv Diameter over screen (mm) SE1 SE SE SE SE5 Cable cross section (mm²) 1-50 0-150 185-00 00-0 800-1000 1-50 0-150 185-0 00-0 800-1000 - 5-0 95-150 185-500 0-1000 - 5-5 50-0 95-00 00-1000 1-18 19-5-0 1-1-5 For use with HSGK range of gland kits when installing lead sheathed cables (PILC). Allows the earthing of the lead sheath without need for plumbing. CK PILC SOLDERLESS EARTH CONNECTION OUTDOOR Indoor kit Part number Outdoor kit Part number Cable cross section Diameter over lead sheath (mm) CK1 CK CK CK CK1-O CK-O CK-O CK-O 1-95 mm² 10-185 mm² 0-00 mm² 00-500 mm² 8-9 0-50 51-0 1-80
HSGK CABLE GLAND KIT Made to comply with stud spacings to BS 5. For indoor and outdoor use on switchgear or transformer cable boxes. They provide an effective moisture seal around the cable sheath and earth armour wires. Also extends space for termination by 150mm. KIT CONTENTS The kit includes metal gland body, heat-shrinkable sleeve, armour clamps, copper braid and mastic tape. Part number Cable cross section HSGK1 HSGK HSGK (pack of ) -core cables with an under armour diameter of up to mm -core cables with an under armour diameter of up to 9 mm 1-core cables with an under armour diameter of up to mm RAE KITS REMOTE ARMOUR EARTHING Under Armour Earthing kits for use in applications where glands are not being utilised. KIT CONTENTS 1 x CK Braid x Under armour ring x Jubilee clips 1 x MBA Mastic x SE Braid 1 x MSRTK tubing Part no s are available upon request, please provide full cable specification. 10/01
MULTI CORE HEAT-SHRINK BREAKOUT KIT XCK-HSS For environmental protection of the exposed cores and crutch of and core polymeric insulated cables when terminated with Nexans screened separable connectors. DESIGN The kit consists of a heat shrink breakout, core tubes, sealing mastic and installation instructions. ORDERING INSTRUCTIONS The breakout kits are made up specific to cable requirements. When ordering please give diameter of core insulation, overall diameter of cable and number of cores (for core cables please state whether all core insulations are the same diameter). If these are not known please give kv rating, core size in sqmm, number of cores and whether armoured/ unarmoured. For relevant solderless earth kits for copper tape screened cables please refer to the appropriate section in the catalogue. Please note these are not termination kits and relevant cable terminations are to be used in conjunction with these kits. For tail lengths up to 00 mm
ENQUIRY SHEET Email to: sales.npa@nexans.com YOUR COMPANY DETAILS: Company: Town: Tel.: Fax: Contact: GENERAL System voltage kv Load current Amp Fault level ka sec No. of cores: Conductor material: Al Cu Armour: None SWA STA Installation area: Indoor Outdoor CABLE TYPE XLPE EPR Cu tape screen Cu wire screen PICAS PILC Screened Belted Cable cross section mm² PRODUCT TYPE Termination Tail length mm Joint Separable connector TECHNOLOGY Heat shrinkable Cold shrinkable Slip-on 15TS Euromold Resin ACCESSORIES Earthing kit Bushing boots Cable lugs Ferrules Gland kit Heat-shrinkable Core insulation diameter mm 10/01
NOTES
09/01