White - ft Bed - etachable with Slatsbunkbed ssembly Instructions - Please keep for future reference 80 9 Ladder can be fitted right or left side. This is a universal bunkbed that can be used on its own or with one of the optional storage solutions show below 0 POSITION Use this position if adding the Under bed Storage Unit POSITION Use this position if adding the Truckle/drawer imensions Width - 08, 8cmcm epth - 0, 0cmcm eight -09cm,cm Important Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the ustomer elpline: 08 8008 80 NR-V Issue - /0/ /0/0
IMPORTNT, R RFULLY - RTIN FOR FUTUR RFRN Warning! hildren can become trapped between the bed and the wall. To avoid risk of serious injury the distance between the top safety barrel and the wall shall not exceed mm or shall be more than 0mm., cm The bunk bed meets the european N -:0 standards for security and durability. The bunk bed meets the Bunk Beds (ntrapment azards) (Safety) Regulations 98 Before Starting ssembly are and maintenance Only clean using a damp cloth and mind detergent, do not use bleach or abrasive cleaners. Regularly check that there are no loose screws on this unit and retighten when necessary. Parts of your product are produced from solid pine which is a natural product containing a beautiful wooden structure. irect sunlight can speed up the natural process of the resin contained in the pine knots to change colour around knots. This is a normal process happening to natural wood and cannot be seen as a manufacturers fault. ll wood has been dryed to Industry standards for furniture timber and all procedures for obtaining the best lacquring finish have been followed. Our furniture will endure most temperatures in the home but it is best to avoid placing furniture next to heat sources as radiators or fire. Be particularly careful with solid wood as the lack of humidity caused by central heating can cause damage such as warping. Glue safety - Take care when using glue, please follow the advice below Skin contact: Remove contamination by washing with soap and water. This procedure should also be followed prior to eating and drinking. ye contact: Rinse immediately with clean water for minutes and seek medical advice. If swallowed: Seek medical advice immediately. Safety when using your bed o not allow children to climb over the safety rails. lways use the ladder when climbing in and out of bed. Never attempt to hang bags, bunting or other items with strings or handles on the bed.
omponents - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. B F 0x0 Wooden dowel x x0mm Screw x 8 Sector x 8 owel Ø8x0 x onformat screw Øx 0mm x0 Screw. x mm x0 F Mx Bolt x 8 K Mx0x ross dowel x 8 L,x0mm Screw x Barrel nut Ø0 x mm x llen key mm x over cap Ø/Ø8 x G J N x0mm Screw x 0 P x80 Wooden owel x Q,x Screw x 8 over cap Ø8/Ø x Spacer 0xxmm x K L onnecting M bolt M x 0mm x mm Screw x,x0 Screw x x over ap x 0 R S T onnecting bolt M x mm x9 Metal dowel x 8x over ap x 0x over ap x U P R S T over cap Ø/Ø over x ap x V U over cap Ø0/Ø over ap xx 8 Locking nut x x8 over ap x Y over cap Ø/Ø mm llen key x0x Tools reqiured Philips screwdriver (medium) Small hammer Flathead screwdriver (medium) Rubber hammer Rubber hammer Rubber hammer llen key (incl) cm 8 9 0 inch Rulers - Use this ruler to help correctly identify the screws
omponents - Panels 9 0 8 0 9 8
omponents - Panels Front Bed rail x (00,x,x cm) Rear Bed rail x (00,x,x cm) Front safety rail x Rear safety rail x (,x,x cm) (00,x,x cm) nd rail x (80,x,x cm) nd rail x (80,x,x cm) nd panel x (80,x8x cm) 8 Leg x (x9x,8 cm) 9 Leg x (x9x,8 cm) 0 Leg x (89,x9x,8 cm) Leg x (89,x9x,8 cm) Step x (x,8x, cm) Ladder side x (,8x9x cm) Slats x
ssembly Instructions Step Fitting dowels In this step use this fitting: Insert wooden dowels into the holes in bed rails, headboard xrails,, footboard and bottomrail. x x Insert dowels into the nessesary holes in bedto rails, tap end the rails dowel and safety in very rails. gently with necessary to tap dowel in very gently with x x x x x x x x x x Insert wooden dowels into the holes in headboard panels and. Step nessesary to tap the dowel in very gently with In this step use this fitting: x x x B B x8 Step Screw connecting screws into holes of legs using mm llen key. ssembling headboard Position details and attach headboard panels showed on illustration at side. B x B mm B 0 x 8 x 9 B x
ssembly Instructions Step Fitting dowels In this step use this fitting: Insert wooden dowels into the holes xin bed rails, headboard rails U x,, footboard and bottomrail. U x Position legs. Insert sectors into mm holes on end panel as shown in the picture. nessesary to tap the Tighten dowel screws in very with gently mm with llen small key. hammer. over mm holes with cover caps U U U 9 8 Insert wooden dowels Step into the holes in headboard panels In this and step use this fitting:. x Note: It may x be nessesary U to x tap the dowel in very gently with Position legs. Insert sectors into mm holes on end rail as shown in the picture. Step U x Tighten screws with mm llen ssembling key. headboard over mm holes with cover Position capsdetails U and attach headboard panels showed on illustration at side. U U 0
ssembly Instructions Step In Fitting this step dowels use this fitting: Insert wooden dowels into the holes x in bed rails, headboard x rails,, footboard and bottomrail. Push ross dowel into hole in bed rails and the groove on ross dowel should Note: be It may horizontal. be nessesary to tap the Push dowel Bolt in very through gently each with leg to meet ross dowel and small then hammer. fasten with the llen key. Step Insert wooden dowels into the holes in headboard panels In and this step. use this fitting: x POSITION POSITION (using under bed Storage Unit) (using Truckle/drawer) Note: It may xbe nessesary to xtap the dowel in very gently with F x Push ross dowel into hole in bed rail and the groove on ross dowel should be horizontal. Step Push Bolt through each leg ssembling to meet ross dowel and headboard then fasten with the llen key. Position details and ttach attach the headboard rear safetypanels rail to the legs with the screws F showed on illustration at Tighten with llen key side. F F F 8
ssembly Instructions Step InFitting this step dowels use this fitting: Insert wooden x dowels into the holes in bed rails J x8, headboard rails,, footboard and Insert bottomrail owels. into the holes in lower bunk legs. Place upper bunk on lower bunk as shown on illustration. nessesary to tap the Fix dowel dowels in very in legs gently with with screws J using Philips screwdriver. J J J J J Step 8 Insert wooden dowels into the holes in Inheadboard this step use panels this fitting: and. G x nessesary M to x tap the dowel in very gently with ssemble ladder sides and steps as shown in the picture. Use connecting screws and Step mmllen key. x M J lways placed inside the ladder G over the heads of the connection ssembling screws with cover headboard caps Position details and attach headboard panels showed on illustration at side. M G Follow this step if you are assembling bed in position
ssembly Instructions Step 9 InFitting this step dowels use this fitting: Insert wooden dowels G x0 into the holes in bed rails, headboard M x0rails,, footboard and bottomrail. ssemble ladder sides and steps as shown in the picture. Use connecting screws G and Note: mm It may llenbe key. nessesary to tap the over dowel the in very headsgently of thewith connection screws with cover caps M Follow this step if you are assembling bed in position hoose this position if adding Under bed Storage Unit M G Now you must decide if the ladder is placed in the left or the right side. Step 0 Insert wooden dowels into the holes in Inheadboard this step use panels this fitting: and. K x nessesary F to xtap the dowel in very gently with F x K K K Place the ladder as shown on the side of the bed you decided (left or right). Step onnect ladder to Front bed rail using screws K and a mm ssembling llen key. headboard Fix safety rail to ladder with screws Position details and K and with screw F toattach leg. headboard panels showed on illustration at side. K K 0
ssembly Instructions Step InFitting this step dowels use this fitting: T Insert wooden dowels P x into the holes in bed rails, headboard x9 rails R T,, footboard x and bottomrail. over the heads of screws and bolts with cover caps. over nessesary all unused to tap holes the with cover dowel caps in very as shown. gently with T T P x P T R P R P x x R P x R P x x T T P x P T P x Step Insert wooden dowels into the holes in Inheadboard this step use panels this fitting: and. L x nessesary to tap the Position dowel in slats very equally. gently with nd small slats hammer. must be in contact with legs. L L P T x L P R T P R P P T POSITION POSITION x L Place two screws in each slat and tighten using a Philips Step screwdriver. ssembling headboard Position details and attach headboard panels showed on illustration at side.
ssembly Instructions Step InFitting this step dowels use this fitting: Insert wooden dowels into the holes in bed rails U, headboard rails etaching,, footboard the Bunkbed and into separate bottomrail beds.. U U Turn end rail in upper bunk ends by taking cover cap U off Note: and releasing It may be fitting B and nessesary to tap the Retighten fitting B and and dowel push in cover very cap gently with U back on. Step Insert wooden dowels into the holes in Inheadboard this step use panels this fitting: and. S x S S Note: It may x be nessesary to tap the dowel in very gently with ssemble separate beds as shown. Use upper bunk endpanels asstep headboard and lower bunk endpanels as footboard. over ssembling all unused holes with cover headboard caps as shown. Position details and attach headboard panels showed on illustration at side. S S
ustomer Service Form Please return complete to Fax: 00 0 Name: ddress: ontact No: ate of purchase: Place of purchase: Product Name: See assembly instructions: Problem: Parts Needed: Part No. Quantity Please quote assembly instruction or number escription e.g drawer base