MODEL VIEWS MY NOT REPRESENT EXCT MODEL PURCHSED : : : LL VLUES ± OVERLL CRETED 1 OF 5 K:\DIVERSIFIED\\CD\.dwg, 11/30/2015 9:58:11 M, DWG To PDF.pc3
TOOLS REQUIRED 1 2 " WRENCH 1 2 " SOCKET ND TORQUE WRENCH OPTIONL 4MM LLEN WRENCH SSEMBLY COMPONE ITEMS INCLUDED PRT # PRT QTY ON SSEMBLY N/ ON ND BRCKET SSEMBLY (FCTORY SSEMBLED) TOP 170036 TOP,PLM,25X30X72,LMOND 1 1 CBINET N/ 35"W X 28"D X 35.75"H 1 LEGS 501102 LEG,MPL 2.25X2.25X35.00 2 LEG BRCE N/ LEG BRCE 24.00" LONG 1 STRETCHER N/ STRETCHER 32.00" LONG 1 LEG HRDWRE KIT 520001 LEG HRDWRE KIT, 1 LEG 2 LEG BOOTS 100076 LEG BOOT,BLK RUBBER 2 CONFIRMTS LEGS 227578 CONFIRMTS STRETCHER 228564 SCREW,7MMX90MM,CONN,LLENHED, BLCK SCREW,7MMX50MM,CONN,LLENHED, BLCK BOLT INTERNL ON 231922 BOLT, 3 8 16X625 HEX HED 2 WSHER INTERNL ON 100451 WSHER, 5 16 FLT ZINC PLTED 2 SCREWS TOP 100641 SCREW,#8X1 3 4" QUD RD WSH HD 12 4 4 : : : LL VLUES ± OVERLL TOOLS ND SSEMBLY COMPONE CRETED 2 OF 5 K:\DIVERSIFIED\\CD\.dwg, 11/30/2015 9:58:15 M, DWG To PDF.pc3
LEG LEVELER LEG BRCE ROUNDED EDGES FCING UP LEG BOOT INSERT HNGER BOLT THROUGH HERE WITH LOCK WSHER ND HEX NUT CLOSE UP OF CORNER LEG SSEMBLY CLOSE UP OF LEG BOOT ND LEG LEVELER SSEMBLY STEP 1: STEP 2: STEP 3: STEP 4: LY ON SSEMBLY ON FLOOR WITH ROUNDED EDGES FCING UP. INSERT HNGER BOLT ON ONE OF THE LEGS THROUGH THE CORNER BRCKET ND INSERT LOCK WSHER ND HEX NUT. USING 1 2" WRENCH OR 1 2" SOCKET ND TORQUE WRENCH, SCREW ON THE NUT BUT DO NOT TIGHTEN LL THE WY. REPET FOR THE OTHER LEG. SLIDE LEG BOOT ONTO LEGS WITH FLRED END TOWRDS THE BOTTOM OF THE LEG. SCREW LEG LEVELERS INTO TNUT ON BOTTOM OF THE LEGS. USING 4MM LLEN WRENCH, INSERT THE CONFIRMTS INTO ONE LEG ND SCREW INTO THE BRCE. REPET FOR THE OTHER LEG. MKE SURE BRCE IS STRIGHT ND LL CONFIRMTS RE TIGHT. : : : LL VLUES ± OVERLL CRETED 3 OF 5 K:\DIVERSIFIED\\CD\.dwg, 11/30/2015 9:58:21 M, DWG To PDF.pc3
STRETCHER CONFIRMTS OUTSIDE OF CBINET SHOWN INSIDE OF CBINET SHOWN STEP 4: INSERT STRETCHER ONCE LEG BRCE IS IN POSITION. TTCH STRETCHER USING THE CONFIRMTS PROVIDED. GO BCK TO STEP 2 ND TIGHTEN UP THE HNGER BOLTS FOR ECH LEG USING 1 2" WRENCH OR 1 2" SOCKET ND TORQUE WRENCH, TO MINIMUM OF 12FT LBS BUT NOT TO EXCEED 17FT LBS. STEP 5: FLIP ON SSEMBLY OVER ONTO THE LEGS. LIGN THE HOLES ON THE STRETCHER TO THE HOLES ON THE LEFT SIDE OF THE CBINET. TKE OUT THE TOP DRWERS TO TTCH THE STRETCHER FROM INSIDE THE CBINET. SCREW CONFIRMTS INTO THE STRETCHER. : : : LL VLUES ± OVERLL CRETED 4 OF 5 K:\DIVERSIFIED\\CD\.dwg, 11/30/2015 9:58:26 M, DWG To PDF.pc3
TTCH ON SSEMBLY TO CBINET THROUGH HERE ND ON OTHER BRCKET INTERNL ON POCKET HOLES BCK ON BRCKETS FRONT ON CLOSE UP OF ON SSEMBLY SHOWN COMPLETE UNIT SHOWN STEP 6: POSITION ON SSEMBLY SO INNER HOLES OF THE BRCKETS ON INTERNL ON RE LINED UP WITH THE TWO HOLES ON LEFT SIDE OF CBINET (THE FRONT ON WILL BE FLUSH WITH THE FRONT OF THE CBINET ND THE BCK ON WILL BE FLUSH WITH THE BCK OF THE CBINET). INSERT THE TWO BOLTS ND WSHERS THT RE PROVIDED INTO THOSE HOLES ND TIGHTEN. DJUST LEG LEVELERS TO LEVEL ON SSEMBLY WITH THE CBINET. STEP 7: SET TOP ON UNIT ND DJUST FOR PROPER OVERHNG (1" OVERHNG ON THE SIDES ND 2" OVERHNG ON THE FRONT ND BCK). TTCH TOP BY GOING INSIDE CBINET ND SCREWING UP THROUGH THE TOP (NOT SHOWN) ND BY GOING UNDERNETH UNIT ND SCREWING INTO THE POCKET HOLES ON THE ON SSEMBLY. MKE SURE SCREWS RE TIGHT ND TOP IS SECURE. STEP 8: PUT TOP DRWERS BCK IN. PLCE UNIT IN DESIRED LOCTION. : : : LL VLUES ± OVERLL CRETED 5 OF 5 K:\DIVERSIFIED\\CD\.dwg, 11/30/2015 9:58:31 M, DWG To PDF.pc3