Wahl WR Series Industrial RTD Probes Ordering Form Step 1 - Select: RTD Sensor from WR Codes WR1 RTD Sensor - Standard 304 SS WR2 RTD Sensor - Standard 316 SS Step 2 - Select: Process Connection from corresponding Codes under chosen Sensor Code Standard Process Connection Price Add $ A 1/2" x 1/2" NPT, No Lagging Extension B 1/2" x 3/4" NPT, No Lagging Extension F 2" Lagging Extension, 1/2" x 3/4" NPT G 4" Lagging Extension, 1/2" x 3/4" NPT H 6" Lagging Extension, 1/2" x 3/4" NPT WR3 RTD Sensor - Compression 304 SS Code Compression Process Connections Price Add $ J 1/2" x 1/2" NPT, Compression Fitting WR4 RTD Sensor - Spring Loaded 316 SS Code Spring Loaded Process Connections Price Add $ K 1/2" x 1/2" NPT, Spring Loaded Fitting WR5 RTD Sensor - Sanitary 316 SS Code Sanitary Process Connections Price Add $ L 1-1/2" Flange M 2" Flange N 2-1/2" Flange P 3" Flange Insert Codes below and carry over to next page: SubTotal 66
Wahl WR Series Industrial RTD Probes Ordering Form continued Step 3 - Select: RTD Type Code RTD Type Price Add $ 1 Thin Film, Class A, 100 ohm (.00385), -58 to 400 F (-50 to 204 C) 2 Thin Film, Class B, 100 ohm (.00385), -58 to 400 F (-50 to 204 C) 3 Wire Wound, Class A, 100 ohm (.00385), -58 to 400 F (-50 to 204 C) 4 Wire Wound, Class B, 100 ohm (.00385), -58 to 400 F (-50 to 204 C) Step 4 - Select: Stem Diameter Code Stem Diameter Price Add $ 0 NA NA 1 1/4" 2 3/8" (not available on WR4) Step 5 - Select: Wire Configuration Code Wire Configuration Price Add $ 2 2 Wire Teflon 3 3 Wire Teflon 4 4 Wire Teflon Step 6 - Select: Stem Length Code Stem Length Price Add $ 01X-12X 1" to 12" Length in inches - 01X = 1 inch, 02X = 2 inch, 03X = 3 inch, etc. For fractional lengths substitute X with: A = 1/4", B = 1/2", C = 3/4, Example: 03B = 3-1/2". 13X - 72X 13" to 72" Length in inches. For fractional lengths substitute X with: A = 1/4", B = 1/2", C = 3/4", Example: 13B = 13-1/2". NC Codes from previous page: Codes from above: Step 7 - Select: Connection and enter corresponding Model number in Step 8 below Code Connections Price Add $ 0 No Connection Head N/A 1 Connection Head with Terminal Block* 2 Connection Head with Transmitter* * Specify desired Connection Head, Terminal Block, Transmitter and Transmitter Programming Kit as separate line items below. SubTotal from previous page: SubTotal from above: Sensor TOTAL Step 8: Enter Model Number for desired unit below: Model Type Unit Price Connection Head Temperature Transmitter Terminal Block Accessory Transmitter Programming Kit *For Transmitters Specify: Temperature Set Points: 4 ma and 20 ma. Burnout: High or Low For other configurations contact your Wahl Distributor 67
Wahl WT Series Thermocouple Probes Ordering Form Step 1 - Select: Thermocouple Sensor from WT Codes WT1 Thermocouple Sensor - Standard 304 SS WT2 Thermocouple Sensor - Standard 316 SS Step 2 - Select: Process Connection from corresponding Codes under chosen Sensor Code Standard Process Connection Price Add $ A 1/2" x 1/2" NPT, No Lagging Extension B 1/2" x 3/4" NPT, No Lagging Extension F 2" Lagging Extension, 1/2" x 3/4" NPT G 4" Lagging Extension, 1/2" x 3/4" NPT H 6" Lagging Extension, 1/2" x 3/4" NPT WT3 Thermocouple Sensor - Compression 304 SS Code Compression Process Connections Price Add $ J 1/2" x 1/2" NPT, Compression Fitting WT4 Thermocouple Sensor - Spring Loaded 316 SS Code Spring Loaded Process Connections Price Add $ K 1/2" x 1/2" NPT, Spring Loaded Fitting WT5 Thermocouple Sensor - Sanitary 316 SS Code Sanitary Process Connections Price Add $ L 1-1/2" Flange M 2" Flange N 2-1/2" Flange P 3" Flange Insert Codes below and carry over to next page: SubTotal 68
Wahl WT Series Thermocouple Probes Ordering Form continued Step 3 - Select: Thermocouple Type Code Thermocouple Type Price Add $ J Iron - Constantan K Chromel - Alumel T Copper - Constantan Step 4 - Select: Stem Diameter Code Stem Diameter Price Add $ 0 1/8" (not available on WT4 or WT5) 1 1/4" 2 3/8" (not available on WR4) Step 5 - Select: Stem Tip Code Stem Tip Price Add $ G Grounded NC U Ungrounded Step 6 - Select: Stem Length Code Stem Length Price Add $ 01X-12X 13X - 72X 1" to 12" Length in inches - 01X = 1 inch, 02X = 2 inch, 03X = 3 inch, etc. For fractional lengths substitute X with: A = 1/4", B = 1/2", C = 3/4", Example: 03B = 3-1/2". 13" to 72" Length in inches. For fractional lengths substitute X with: A = 1/4", B = 1/2", C = 3/4", Example: 13B = 13-1/2". NC Step 7 - Select: Connection and enter corresponding Model number in Step 8 below Code Connections Price Add $ 0 No Connection Head N/A 1 Connection Head with Terminal Block* 2 Connection Head with Transmitter* Codes from previous page: Codes from above: SubTotal from previous page: SubTotal from above: Sensor TOTAL Step 8: Enter Model Number for desired unit below: Model Type Unit Price Connection Head Temperature Transmitter Terminal Block Accessory Transmitter Programming Kit For other configurations contact your Wahl Distributor *For Transmitters Specify: Temperature Set Points: 4 ma and 20 ma. Burnout: High or Low 69
Sensors RTD & T/C Pricing & Order Form Effective July 1, to December 31, 2017 General Purpose Connection Heads Model Type Material Head Type Process Conduit Price 12401-02 General Purpose Aluminum Screw Top 1/2" NPT 1/2" NPT 12401-03 General Purpose Aluminum Flip Top 1/2" NPT 1/2" NPT 12401-06 General Purpose Polypropylene Screw Top 1/2" NPT 3/4" NPT 12401-08 General Purpose Cast Iron Screw Top 1/2" NPT 1/2" NPT 12401-09 General Purpose 316SS Screw Top 1/2" NPT 3/4" NPT 12401-10 General Purpose Aluminum Screw Top 1/2" NPT 3/4" NPT 12401-11 General Purpose Cast Iron Screw Top 1/2" NPT 3/4" NPT 12401-19 General Purpose Aluminum Flip Top 1/2" NPT 3/4" NPT Explosion Proof Connection Heads Model Type Material Head Type Process Conduit Price 12401-13 Explosion Proof 316SS Screw Top 1/2" NPT 1/2" NPT 12401-14 Explosion Proof 316SS Screw Top 1/2" NPT 3/4" NPT 12401-16 Explosion Proof Cast Aluminum Screw Top 1/2" NPT 1/2" NPT 12401-17 Explosion Proof Cast Aluminum Screw Top 1/2" NPT 3/4" NPT Temperature Transmitters Model Type Approvals Price 12415-08 PC-Programmable Non-hazardous area, Galvanic isolation 12415-09 PC-Programmable FM (FM, Class I, Div 1, Intrinsically Safe Groups A, B, C, and D) 12415-10 Protocol - HART Non-hazardous area, Galvanic isolation 12415-11 Protocol - HART FM (FM, Class I,II,III, Div 1, Intrinsically Safe Groups A, B, C, D, and G) 12415-12 PC-Programmable Non-hazardous area, Non-isolated, Low Profile NOTE: Specify Temperature Set Points for 4mA and 20mA; and Burnout: Hi or Low at time of ordering. NOTE: Temperature Transmitter models 12415-03,12415-05,12415-06,12415-07 have been replaced by the models above. Terminal Blocks Model Type Material Price 12405-01 4 Position Ceramic 12405-02 6 Position Ceramic 12405-05 2 Position Ceramic Model Transmitter Programming Kits Price 12415-04 Transmitter Programming Kit for E&H Transmitters: 12415-03, -05, -06, -07 POA* 12415-13 Transmitter Programming Kit for INOR Transmitters: 12415-08, -09, -12* 12415-14 Transmitter Programming Kit for INOR Transmitters: 12415-08, -09 * NOTE: -10 and -11 Transmitters must be programmed using a user provided Hart communicator/modem. *POA - Priced on Application 70