E M C C o m p o n e n t s July 23 Chip Beads For power line MP series MP63 MP5 MP68 MP22 63[2 inch]* 5[42 inch] 68[63 inch] 22[85 inch] * Dimensions Code JIS[EIA]
(2/23) EMINDES FO USING THESE PODUCTS Before using these products, be sure to request the delivery specifications. SAFETY EMINDES Please pay sufficient attention to the warnings for safe designing when using these products. EMINDES The storage period is less than 2 months. Be sure to follow the storage conditions (Temperature: 5 to 4 C, Humidity: to 75% H or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 5 C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. () Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment () Electric heating apparatus, burning equipment () Disaster prevention/crime prevention equipment (2) Safety equipment (3) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. - / 23723 / e943_mpz.fm
(3/23) Chip Beads For power line Overview of the MP Series Product compatible with ohs directive Halogen-free Compatible with lead-free solders FEATUES Noise reduction solution for power supply lines. Compared to the conventional MM Series, has low direct current resistance for compatibility with large currents, optimal for low power consumption. Lineup includes 4 sizes from 63 to 22. Achieves various frequency characteristics by using 5 materials with different features. Multilayer integration monolithic structure makes it highly reliable. There is no directivity. APPLICATION Smart phones, tablets, portable memory audio devices, various modules, PCs, note PCs, TVs, STBs, Blu-ray recorders, DSCs, and DVCs Power supply line noise removal for game machines, smart grids, industrial equipment, etc. PAT NUMBE CONSTUCTION MP 63 S 22 C T Series name L W T Dimensions Impedance Characteristic Material name (mm) ( ) at MHz type Packaging style 63.6.3x.3 S 22 22 C T Taping 5..5x.5 Y A 68.6.8x.6 B B.6.8x.8 22 2..25x.85 D Internal code OPEATING TEMPEATUE ANGE, PACKAGE QUANTITY, PODUCT WEIGHT Type Operating temperature Temperature range Storage temperature Package quantity Individual weight C C pieces/reel mg MP63 55 to +25 55 to +25 5,.3 MP5 4 to +85 4 to +85, MP68 t=.6mm 55 to +25 55 to +25 4, 3 t=.8mm 55 to +25 55 to +25 4, 4 MP22 55 to +25 55 to +25 4, 8 Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. ohs Directive Compliant Product: See the following for more details related to ohs Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 9ppm, Br content is less than 9ppm, and that the total Cl and Br content is less than 5ppm. - / 23723 / e943_mpz.fm
(4/23) Overview of the MP Series ECOMMENDED EFLOW POFILE Preheating Soldering Peak T4 Natural cooling T: Temperature T2 T3 t3 T3 T t t2 t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T T2 t T3 t2 T4 t3 5 C 8 C 6 to 2s 23 C 3 to 6s 25 to 26 C s - / 23723 / e943_mpz.fm
(5/23) Overview of the MP Series MATEIAL CHAACTEISTICS B material: This type is perfectly suited for fast digital signals. By equalizing components and components that beads possess at a frequency of 5MHz, it is able to suppress overshooting, undershooting and ringing of fast digital signals. material: For wide frequency applications calling for broad impedance characteristics. For digital signal line applications calling requiring good waveform integrity. Impedance values selected for effectiveness at to 2MHz. S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near MHz. Impedance values selected for effectiveness at 4 to 3MHz. Y material: High frequency range type intended for the MHz region and above. For signal line applications in which the signal frequency is far from the cutoff frequency. Impedance values selected for effectiveness at 8 to 4MHz. D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies. Designed for high impedance at high frequencies (3MHz to GHz) for signal line applications. TYPICAL MATEIAL IMPEDANCE CHAACTEISTICS 25 D 2 Y Impedance(Ω) 5 5 B S Frequency(MHz) - / 23723 / e943_mpz.fm
(6/23) MP series MP63 Type SHAPE & DIMENSIONS.6±.3.3±.3.3±.3.min. Dimensions in mm ECOMMENDED LAND PATTEN.3.25.3.25 Dimensions in mm - / 23723 / e943_mpz.fm
(7/23) MP series MP63 Type ELECTICAL CHAACTEISTICS CHAACTEISTICS SPECIFICATION TABLE Impedance DC resistance ated current [MHz] ( )max. (ma)max. ( ) Tolerance Part No. 22 ±25%.65 MP63S22CT 33 ±25%.9 75 MP63S33CT 47 ±25%.2 5 MP63S47CT Measurement equipment Measurement item Product No. Manufacturer Impedance E499A+697 Agilent Technologies DC resistance Type-7556 Yokogawa Equivalent measurement equipment may be used. - / 23723 / e943_mpz.fm
(8/23) MP series MP63 Type ELECTICAL CHAACTEISTICS VS. FEQUENCY CHAACTEISTICS (BY SEIES) MP63S SEIES 9 8 MP63S47C 7 6 5 4 3 2 MP63S33C MP63S22C - / 23723 / e943_mpz.fm
(9/23) MP series MP63 Type ELECTICAL CHAACTEISTICS,, VS. FEQUENCY CHAACTEISTICS MP63S22C MP63S33C MP63S47C 45 4 35 3 25 2 5 5 7 6 5 4 3 2 8 6 4 2 - / 23723 / e943_mpz.fm
(/23) MP series MP5 Type SHAPE & DIMENSIONS ±.5.5±.5.5±.5.min. Dimensions in mm ECOMMENDED LAND PATTEN.5.5.4.5 Dimensions in mm - / 23723 / e943_mpz.fm
(/23) MP series MP5 Type ELECTICAL CHAACTEISTICS CHAACTEISTICS SPECIFICATION TABLE Impedance DC resistance ated current [MHz] ( )max. (A)max. ( ) Tolerance Part No. ±5.25 2. MP5SCT 3 ±.35.7 MP5S3CT 6 ±25%.6.5 MP5S6CT 2 ±25%.9.2 MP5S2CT 9 ±25%..2 MP5Y9CT Measurement equipment Measurement item Product No. Manufacturer Impedance E499A+692A Agilent Technologies DC resistance Type-7556 Yokogawa Equivalent measurement equipment may be used. - / 23723 / e943_mpz.fm
(2/23) MP series MP5 Type ELECTICAL CHAACTEISTICS VS. FEQUENCY CHAACTEISTICS (BY SEIES) MP5S SEIES MP5Y SEIES 25 25 MP5Y9C 2 MP5S6C MP5S2C 2 5 MP5S3C MP5SC 5 5 5 - / 23723 / e943_mpz.fm
(3/23) MP series MP5 Type ELECTICAL CHAACTEISTICS,, VS. FEQUENCY CHAACTEISTICS MP5SC MP5S3C MP5S6C 8 6 4 2 8 6 4 2 5 4 3 2 8 6 4 2 MP5S2C MP5Y9C 2 25 5 5 2 5 5 - / 23723 / e943_mpz.fm
(4/23) MP series MP68 Type SHAPE & DIMENSIONS.6±.5 T.8±.5.3±.2 Thickness(T).6±.5mm.8±.5mm Dimensions in mm ECOMMENDED LAND PATTEN.8.6.8.6 Dimensions in mm - / 23723 / e943_mpz.fm
(5/23) MP series MP68 Type ELECTICAL CHAACTEISTICS CHAACTEISTICS SPECIFICATION TABLE Impedance DC resistance ated current [MHz] Thickness T ( )max. (A)max. (mm) ( ) Tolerance Part No. 47 ±25%.5..8 MP68B47AT 26 ±25%.7 6..6 MP68S26AT 3 ±. 5..6 MP68S3AT 6 ±25%.2 3.5.6 MP68S6AT ±25%.3 3..6 MP68SAT 2 ±25%.45 2..6 MP68S2AT 8 ±25%.5 2..6 MP68S8AT 22 ±25%.5 2.2.8 MP68S22AT 33 ±25%.8.7.8 MP68S33AT 47 ±25%.5..8 MP68S47AT 6 ±25%.5..8 MP68S6AT ±25%.3.8.8 MP68S2AT 39 ±25%.2.2.8 MP6839AT 6 ±25%.3 2.3.8 MP68Y6BT ±25%.4 2..8 MP68YBT 5 ±25%.5.8.8 MP68Y5BT 22 ±25%..5.8 MP68Y22BT 3 ±.6.8.8 MP68D3BT 6 ±25%..2.8 MP68D6BT ±25%.5..8 MP68DBT Please refer to the graph of ATED CUENT vs. TEMPEATUE CHAACTEISTICS (derating) about the rating current at 85 C or more in temperature of the product. Measurement equipment Measurement item Product No. Manufacturer Impedance E499A+692A Agilent Technologies DC resistance Type-7556 Yokogawa Equivalent measurement equipment may be used. ated current vs. temperature characteristics (derating) 7 6 ated current (A) 5 4 3 2 55 35 5 5 25 45 65 85 5 25 Temperature ( C) S26A S3A S6A SA Y6B S22A S2A,S8A,YB Y5B,D3B S33A Y22B 39A,D6B B47A,S47A,S6A,DB S2A - / 23723 / e943_mpz.fm
(6/23) MP series MP68 Type ELECTICAL CHAACTEISTICS VS. FEQUENCY CHAACTEISTICS (BY SEIES) MP68B SEIES MP68S SEIES MP68 SEIES 5 4 3 2 MP68B47A 2 MP68S33A MP68S22A MP68S8A 9 MP68S2A 8 MP68SA MP68S6A 7 MP68S26A MP68S3A 6 5 4 3 2 MP68S2A MP68S6A MP68S47A 5 4 3 2 MP6839A MP68Y SEIES 35 MP68Y22B 3 MP68Y5B 25 MP68YB 2 5 MP68D SEIES 6 MP68DB 5 4 MP68D6B 3 2 5 MP68Y6B MP68D3B - / 23723 / e943_mpz.fm
(7/23) MP series MP68 Type ELECTICAL CHAACTEISTICS,, VS. FEQUENCY CHAACTEISTICS MP68B47A MP68S26A MP68S3A 5 4 3 2 4 35 3 25 2 5 5 4 35 3 25 2 5 5 MP68S6A MP68SA MP68S2A 8 6 4 2 6 4 2 8 6 4 2 2 5 5 MP68S8A MP68S22A MP68S33A 3 25 2 5 5 3 25 2 5 5 45 4 35 3 25 2 5 5 MP68S47A MP68S6A MP68S2A 7 6 5 4 3 2 8 7 6 5 4 3 2 2 8 6 4 2 MP6839A MP68Y6B MP68YB 5 4 3 2 4 2 8 6 4 2 2 5 5 - / 23723 / e943_mpz.fm
(8/23) MP series MP68 Type ELECTICAL CHAACTEISTICS,, VS. FEQUENCY CHAACTEISTICS MP68Y5B MP68Y22B MP68D3B 3 25 2 5 5 35 3 25 2 5 5 25 2 5 5 MP68D6B 35 3 25 2 5 5 MP68DB 6 5 4 3 2 - / 23723 / e943_mpz.fm
(9/23) MP series MP22 Type SHAPE & DIMENSIONS 2.±.2.85±.2.25±.2.5±.3 Dimensions in mm ECOMMENDED LAND PATTEN.2.8.8 Dimensions in mm - / 23723 / e943_mpz.fm
(2/23) MP series MP22 Type ELECTICAL CHAACTEISTICS CHAACTEISTICS SPECIFICATION TABLE Impedance DC resistance ated current [MHz] ( )max. (A)max. ( ) Tolerance Part No. 3 ±. 6 MP22S3AT ±25%.2 4 MP22SAT 22 ±25%.4 3 MP22S22AT 33 ±25%.5 2.5 MP22S33AT 6 ±25%. 2 MP22S6AT ±25%.5.5 MP22S2AT Please refer to the graph of ATED CUENT vs. TEMPEATUE CHAACTEISTICS (derating) about the rating current at 85 C or more in temperature of the product. Measurement equipment Measurement item Product No. Manufacturer Impedance E499A+692A Agilent Technologies DC resistance Type-7556 Yokogawa Equivalent measurement equipment may be used. ated current vs. temperature characteristics (derating) 7 6 S3A ated current (A) 5 4 3 2 SA S22A S33A S6A S2A 55 35 5 5 25 45 65 85 5 25 Temperature ( C) - / 23723 / e943_mpz.fm
(2/23) MP series MP22 Type ELECTICAL CHAACTEISTICS VS. FEQUENCY CHAACTEISTICS (BY SEIES) MP22S SEIES 2 MP22S22A MP22SA 9 MP22S3A 8 7 6 5 4 3 2 MP22S2A MP22S6A MP22S33A - / 23723 / e943_mpz.fm
(22/23) MP series MP22 Type ELECTICAL CHAACTEISTICS,, VS. FEQUENCY CHAACTEISTICS MP22S3A MP22SA MP22S22A 5 4 3 2 4 2 8 6 4 2 3 25 2 5 5 MP22S33A MP22S6A MP22S2A 4 35 3 25 2 5 5 7 6 5 4 3 2 2 8 6 4 2 - / 23723 / e943_mpz.fm
(23/23) MP series Packaging style EEL DIMENSIONS 2.±.5 ø6min.. ø8±2. ø3±.2 ø2±.8 8.4 +2.. 4.4max. Dimensions in mm TAPE DIMENSIONS.5 +. 2.±.5 4.±. B 3.5±.5.75±. 8.±.3 A P K Dimensions in mm Type A B P K MP63.38±.5.68±.5 2.±.5.5max. MP5.65±..5±. 2.±.5.8max. MP68.±.2.9±.2 4.±..max. MP22.5±.2 2.3±.2 4.±..max. 6min. Taping 2min. Drawing direction 3min. Dimensions in mm - / 23723 / e943_mpz.fm