SEALS FOR HYDROPOWER DOORS, LOCKS, RIVER PORTS AND MARITIME PORTS 2017
WATERTIGHT. Manufacturing Azur Caoutchouc uses compression molding for all of its dam seals. The parts thus vulcanized are uniform, dense et completely free of shrinkage. "J" seal ( J-Seal ) This seal consists of a rounded part called the bulb and of a flat part. Usually, the bulb has a diameter of 1 3/4 (44.45mm). The flat part has a 9/16 thickness and a total length of 4 (101.6mm), from the bulb s tangent to the end. Note that the J-Seal can be produced with nontraditional sized bulb and flat part. This seal is usually full and can be shipped with a hard coated bulb (fluorocarbon). There is an alternative where the bulb is hollowed; the client decides whether such a bulb or such a coating are required, depending on the requirements. The fluorocarbon used by Azur has a 1/16 (1.59mm) thickness and approximately covers a half circumference (180 degrees) on the surface of the bulb. Its exterior forms a link with the bulb itself.
Double-stem seal This seal can be described as a J-Seal with two flat parts. Its dimensions are the same, but it has a span of 6 1/4 (158.75mm). Just like the J-Seal, it can be produced with a hollow bulb, or covered with fluorocarbon. Flat seal In a cross-sectional view, this seal has a rectangular geometry. It has a 9/16 thickness and approximately a 3 width. The seal s lower part is chamfered, and the upper part can also be chamfered since the measurements vary according to the customers specifications. Other types of Azur seals Enclosed you will find a catalog of standard seals and transition parts produced by Azur whose measurements and caracteristics can be adapted to your needs. In addition to these designs, we can also produce seals with other specific profiles. Contact us for a customized quote.
Dimensional tolerance The seal s dimensional tolerance, in sectional view, are % ±5 in relation to the specified dimensions. For the same gate, the seal s dimensional tolerance, in sectional view, must not vary by more than %2 of the total length of the seal. Considering the characteristics of the material, the manufacturing tolerances are relatively generous. Thus, a tolerance of ± 3/8 (10mm) is often given for the bulbs center to center measurement. On the other hand, it is the characteristics of the material (compressible expandable) that allow a precise installation. For fitting purposes, the client is advised to order longer parts. Note that Azur Caoutchouc mesures all parts in the factory to a temperature of 23 C. Generally used materials The variations of the J-Seal and the double stem are generally made in natural rubber with a hardness of 65 +- 5 Duro. The variations of the flat seals are generally made in natural rubber with a hardness of 45 +- 5 Duro. As shown in the following pages, our products follow strict standards and are pre-tested. A certificate of laboratory analysis is provided with each shipment. Contact us if your quotes require another specific material!
CERTIFICATE OF ANALYSIS NATURAL RUBBER 65 SHORE A J-SEAL PROPERTIES ASTM STANDARDS REQUIREMENTS: ASTM C923M BNQ 2622-420 OBTAINED RESULTS SHORE «A» HARDNESS D-2240 65 ±5 DURO 62 DURO TENSILE STRENGTH D-412 MIN 21 MPa 22.68 MPa ELONGATION AT BREAK D-412 MIN 400% 477% 300% MODULUS D-412 MIN 6.2 MPa 13.52 MPa COMPRESSION SET D-395 MAX 30% 20.41% WATER ABSORPTION (VOLUME CHANGE) D-471 MAX 5% 0.64% OZONE RESISTANCE 50 PPHM D-1149 NO CRACKING NO CRACKING (48H @ 40 C) BRITTLENESS AT LOW TEMPERATURES (-40 C) D-2137 NO BREAKING NO BREKING TENSILE AT BREAK AFTER OXIGEN AGING D-572 MIN 16.5 MPa 21.4 MPa (22H @ 70 C) PTFE THICKNESS D-374 1.5 ±0.127mm 1.59mm PTFE SPECIFIC GRAVITY D-297 2.20 ±0.05 g/cm³ 2.201 g/cm³ PTFE TENSILE AT BREAK D-638 MIN 13.7 MPa 18.42 MPa PTFE ELONGATION AT BREAK D-638 MIN 250% 428% WWW.AZURCAOUTCHOUC.COM
ANALYSIS CERTIFICATE NATURAL RUBBER 45 DURO SHORE A FLAT SEAL PROPERTIES ASTM STANDARDS RECOMMENDED RESULTS: ASTM C923M BNQ 2622-420 OBTAINED RESULTS SHORE «A» HARDNESS D-2240 45 ±5 DURO 48 DURO TENSILE STRENGTH D-412 MIN 17.2 MPa 27.80 MPa ELONGATION AT BREAK D-412 MIN 400% 669% 300% MODULUS D-412 MIN 3.1 MPa 9.22 MPa COMPRESSION SET D-395 MAX 30% 18.94% WATER ABSORPTION (VOLUME CHANGE) D-471 MAX 5% 0.64% OZONE RESISTANCE 50 PPHM D-1149 NO CRACKING NO CRACKING (48H @ 40 C) BRITTLENESS AT LOW TEMPERATURES (-40 C) D-2137 NO BREAKING NO BREAKING TENSILE STRENGTH AFTER OXYGEN AGEING (22H @ 70 c) D-572 MIN 13.75 MPa 25.3 MPa WWW.AZURCAOUTCHOUC.COM
Seals connections (vulcanization) The seals are designed so that the number of connections to perform by the gates manufacturer will be limited or avoided, as much as possible. The seals, as well as all the angle pieces, are pre-molded in the factory. The length of each branches of a transition piece (corner) is never below 12 (300mm). Unless conflicting with the shipping requirements, the connections between the transition pieces (corners) and the straight parts are made by hot vulcanization in our factory. The straight parts are automatically supplied in one piece. It is generally recommended that all connections, made both by our factory and the gate manufacturer, be made by hot vulcanization. The ends that are to be spliced need to be cut to a 90 angle according to the thickness. It may be possible that, in certain cases, the seal will have to be vulcanized where the customer is located or in the field. Azur Caoutchouc then rents a portable heating mold specially designed for this task.
Handling and transportation For standard seals (without fluorocarbon), they are normally tightly rolled to obtain a crate size as compact as possible. The seal s distortion is minor and it will not be permanently deformed. On the other hand, shipping of seals with fluorocarbon requires additional care. Those seals are shipped without being bent, in their original form, and the vulcanization points are strengthened by adding support under the base. Usually, Azur ships the seals in rigid crates and suggests direct transportation to where it will be used or stored.
SEAL CATALOGUE FOR HYDROPOWER DOORS, LOCKS, RIVER PORTS AND MARITIME PORTS NB: The profiles shown in this catalogue are a sample of the standard products manufactured at Azur Caoutchouc. They are adaptable and can be modified. Furthermore, Furthermore, Azur Caoutchouc is experienced and can produce the majority of the standard and specific pieces of the industry. Contact us for any request of compression molded and hot vulcanized parts! 2015
BULB TYPES (APLIES FOR ALL SEAL SHAPES AND TRANSITION PIECES, UNLESS EXCLUDED) STANDARD FULL BULB FULL BULB WITH FLUOROCARBON (PTFE 1.5MM) HOLLOWED BULB (ALSO AVAILABLE WITH FLUOROCARBON)
STANDARD PROFILES WITH ONE BULB J-SEAL, OR SINGLE STEM SEAL (1BU1BR) DOUBLE STEM SEAL (1BU2BR)
DOUBLE BULBS STANDARD PROFILES DOUBLE BULB AND SIMPLE STEM SEAL (2BU1BR) DOUBLE BULB AND TRIPLE STEM SEAL (2BU3BR)
SPECIAL PROFILES HOLLOWED DOUBLE BULB AND TRIPLE STEM SEAL (2BU3BR-E) "HOCKEY STICK" SHAPED SEAL FOR RADIAL TYPE HYDROPOWER DOORS
FLAT TRANSITION PIECES (MOLDED CORNERS) SIMPLE STEM TO SIMPLE STEM, WITH INNER BULB TRANSITION PIECE (1BU1BR@1BU1BR-INT) SIMPLE STEM TO SIMPLE STEM WITH OUTER BULB TRANSITION PIECE (1BU1BR@1BU1BR-EXT)
FLAT TRANSITION PIECES (MOLDED CORNERS) DOUBLE STEM TO DOUBLE STEM TRANSITION PIECE (1BU2BR@1BU2BR) DOUBLE BULB TO DOUBLE BULB TRANSITION PIECE (2BU1BR@2BU1BR)
FLAT TRANSITION PIECES (MOLDED CORNERS) TRIPLE STEM TO TRIPLE STEM TRANSITION PIECE (2BU3BR@2BU3BR) TRIPLE STEM WITH DOUBLE BULB TRANSITION PIECE (2BU3BR@2BU1BR)
FLAT TRANSITION PIECES (MOLDED CORNERS) DOUBLE STEM TO SIMPLE STEM WITH INNER BULB TRANSITION PIECE (1BU2BR@1BU1BR-INT) DOUBLE STEM TO SIMPLE STEM WITH OUTER BULB TRANSITION PIECE (1BU2BR@1BU1BR-EXT)
TRANSITION PIECES - 90 (MOLDED CORNERS) SIMPLE STEM TO SIMPLE STEM TRANSITION PIECE (1BU1BR@1BU1BR-90) DOUBLE STEM TO DOUBLE STEM TRANSITION PIECE (1BU2BR@1BU2BR- 90)
OTHER TRANSITION PIECES (MOLDED CORNERS) BI-DIRECTIONNAL SIMPLE STEM TO SIMPLE STEM TRANSITION PIECE (1BU1BR@1BU1BR@1BU1BR) SIMPLE STEM "T" TRANSITION PIECE (1BU1BR@1BU1BR-T)
SPECIAL PIECES TRANSISION PIECE SIMPLE STEM WITH A SQUARE BULB AT THE END (1BU1BR@BC) TRANSITION PIECE SIMPLE STEM WITH A BULB WITH A SQARE BASE AT THE END (1BU1BR@BBC)
FLAT SEALS STANDARD FLAT SEAL (ALSO AVAILABLE WITH CHAMFERS) FLAT SEAL WITH A ROUNDED TIP
COFFERDAM SEALS