Absco Premier Garden Shed Assembly Instructions Model: 33GK FRONT:.6m SIDE:.6m HEIGHT:.00m 360mm CONCRETE SLAB 360mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EDGES DOWNWARDS BY 0mm. 50mm 0mm 50mm THIS WILL ENSURE THAT WATER RUN OFF IS KEPT CLEAR FROM YOUR SHED We thank you for choosing an Australian made shed. For further assistance please visit our detailed instructional video library at Http://www.abscosheds.com.au/watch-videos At ABSCO Industries we are always looking to be number ONE, so please let us know what you think of our instructions. Feedback makes us better. feedback@absco.com.au ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE
GENERAL INSTRUCTIONS Premier Garden Shed - Model: 33GK Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on pages three and four. SITE PREPARATION The site for the shed must be level. An uneven surface may result in misalignment of parts. It is recommended that the shed be set on a 00mm concrete slab and anchored down appropriately (refer to last page for details). Anchor sets are not supplied as standard items with this product as some customers wish to use their own anchoring systems. TOOLS REQUIRED OPTIONAL Normal: 3mm A NOTE ON SAFETY Normal: 4mm & 0mm Masonry: 0mm Some parts may have sharp edges. It is advisable to wear gloves when handling these items and safety glasses if drilling holes. Sensible shoes are highly recommended. Do not erect your shed in windy conditions, ensure that the shed is securely anchored to a solid foundation immediately after construction is completed. It is highly recommended to erect the shed with two or more people. ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE
Model: 33GK COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK STEEL SHEET 785mm X 773mm 30A L = 43mm 83R STEEL SHEET 785mm X 773mm 3A L = 788mm 79B STEEL SHEET 95mm X 773mm 36L L = 773mm 58C STEEL SHEET 95mm X 773mm 36R L = 75mm 58B STEEL SHEET 980mm X 773mm 4D WITH HINGES L = 75mm 58A 6 STEEL SHEET 70mm X 773mm 49A JAMB L= 785mm 89A STEEL SHEET 785mm X 73mm 3A JAMB L= 785mm 89B STEEL SHEET 75mm X 773mm B JAMB L= 788mm 90B PEAK BRACE 5A JAMB L= 0mm 9A L = 43mm 83L 4 LIP TRIM L= 70mm 86A ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 3
Model: 33GK COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK CONTENTS OF FITTINGS PACKET 0 SELF TAPPING SCREWS DOOR PADBOLT A 4mm CSK SCREW & NUT SECURE HINGES 6 TO DOOR DOOR STRAP L: 65mm A 8 SELF DRILLING HEX HEAD TEK SCREWS (NO HOLE REQUIRED) CAP GABLE L: 70mm 4A HEX TEK SCREW DRIVER BIT 6 3mm POP RIVETS SECURE HINGES TO DOOR (ALTERNATIVE FIXING METHOD) 3mm (0.") DRILL BIT ASSEMBLY INSTRUCTIONS DOOR PADBOLT HASP ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 4
Model: 33GK COMPONENTS - SPLICED & RIDGE BEAM QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK 0 CSJ ZARSP JOINER L= 00mm (7.9") RIDGE BEAM JOINER L: 450mm (7.7") THESE COMPONENTS ARE TO BE JOINED TO THESE COMPONENTS L = 6.5 (44.3") 54AL L = 6.5 (44.3") 54AR L = 6.5 (44.3") 54CL L = 6.5 (44.3") 54CR L = 6.5 (44.3") 54BL L = 6.5 (44.3") 54BR L = 6.5 (44.3") 8DL L = 6.5 (44.3") 8DR 4 L = 6.5 (44.3") 8CL 4 L = 6.5 (44.3") 8CR L = 6.5 (44.3") 60BL L = 6.5 (44.3") 60BR RIDGE BEAM 97BL RIDGE BEAM 97BR L = 5mm (45.3") L = 5mm (45.3") ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 5
Premier Garden Shed Model: J33GK INSTRUCTIONS FOR JOINING SPLICED S NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = = CSJ JOIN>> <<JOIN JOIN>> = = J JOIN>> SJ STEP. Position the channels and the CSJ joiner channel so the center of the CSJ is in line with the end of each channel to be joined together. STEP. Join the first channel to the CSJ by inserting the center of the CSJ (on an angle) to the end of the channel where the JOIN>> text is marked. Push down one side of the CSJ until you hear a 'click'. = = JOIN>> <<JOIN JOIN>> = <<JOIN = DRILL 4mm (0.6") x 3mm (0.") ( PER A SIDE) HOLES TO SECURE SECTIONS TOGETHER. (THESE SCREWS MAY HAVE TO BE TEMPORARILY REMOVED AND REPLACED DURING LATER ASSEMBLY) STEP 3. Join the second channel to the CSJ by positioning the <<JOIN end of the channel at the center of the CSJ (on an angle). Push the CSJ into the channel until you here a 'click'. FINISHED The joined channels should now look like the picture above with the CSJ positioned equally inside of the joined channels. PUSH QTY = 0pcs. CSJ PUSH CSJ CSJ CSJ HIGH-SIDE CSJ LOW-SIDE 0mm (0.79") CSJ 5mm (0.59") ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 6
Premier Garden Shed Model: J33GK STEP. PRE-ASSEMBLY OF SPLICED S NOTE: JOIN TOGETHER 0 X SECTIONS USING 0 X JOINERS (PART CSJ) 4 X 8CR 4 X 8CL X 60BR X 60BL X 54AR X 54AL X 54CR X 54CL NOTE: SOME S HAVE HOLES IN THEM - YOU WILL NEED TO RE-DRILL HOLES ON ANY WHERE THE CSJ JOINING COVERS HOLES ON THE S YOU ARE CONNECTING 54CR 53mm (88.7") 60BL 8CR 8CL 60BR 54CL 54AR 54AL 8DL 54BR 54BL = = = = = = 4 x 8C x 60B x 54A x 54C x 54B x 8D X 54BR X 54BL 8DR X 8DR X 8DL ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 7
Premier Garden Shed Model: J33GK INSTRUCTIONS FOR JOINING SPLICED RIDGE BEAM STAGE : PUSH RIDGE BEAMS TOGETHER, MAKE SURE THERE IS A 50mm OVERLAP OF THE RIDGE CAP STAGE : INSERT RIDGE CAP JOINER INTO CONNECTED RIDGE CAPS. MAKE SURE JOINER HAS 5mm IN EACH RIDGE CAP. STAGE 3: TURN RIDGE CAP OVER AND MEASURE 50mm FROM THE END OF EACH RIDGE CAP. PLACE TEK SCREWS IN 50mm INCREMENTS FROM SAID END. REPEAT THIS PROCESS FOR THE OPPOSING HALF OF RIDGE BEAM ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 8
Premier Garden Shed Model: J33GK STEP. PRE-ASSEMBLY OF SPLICED RIDGE BEAM QTY. = TEK SCREW DRIVER BIT QTY. = 8 SELF DRILLING TEK SCREW QTY. = RIDGE BEAM 5mm (45.3") PARTS 97BL & 97BR QTY. = PUSH PUSH PART ZARSP - 450mm (7.7") LONG 6mm (0.63") 97BR ZARSP 00mm (7.9") 50mm (9.8") 97BL 6mm (0.63") (PART 97B) 53mm (88.7") OVERALL LENGTH THE TOP SECTIONS OF CAPPING WILL OVERLAP EACH OTHER AT THE JOIN BY 50mm (.0"). ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 9
Model: 33GK VIEW OF ROOF COMPONENTS 4A 86A 8C 60B 49A 49A 49A 86A 49A 49A 4A 49A 97B 86A ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 86A 8C PAGE 0 NO.
Premier Garden Shed Model: 33GK 83R 5A 30A 36R 3A 4D 36L 3A 89A 9A 89B 79B VIEW OF WALL COMPONENTS 54C ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 54B 30A 4D 3A 36L 83R 8D 36R B 83L 54A A 90B 8C 83L 8C
Model: 33GK ABSCO ASSEMBLY INTRODUCTION The snaptite assembly system locks most perimeter channels to all roof and wall sheets without the need for tools and fasteners. SNAP T TE i SNAP T TE To pre-assemble the four wall panels and two roof panels, the perimeter channels are secured to the top and bottom of each panel using the snaptite system, as detailed on the following pages wherever you see the symbol. SNAP T TE i i HIGH SIDE PUSH HIGH SIDE HIGH SIDE HIGH SIDE PUSH After joining sheets together, position channel over one end of the sheets, gently tapping it over the snaptite lugs, working along the sheets to the other end. Position sheets on timbers, trestles or partly over edge of concrete slab. FASTENING SYMBOLS D PUSH HIGH SIDE Join components together by pre-drilling the holes first. Use one component as a template to mark where the holes are. Drill with 3mm drill bit. Join components together with one screw at this location only, as some channel sections have extra holes that are not required for this model of garden shed Do not join components together at this location yet, as the screw may obstruct further assembly of other components ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 Each perimeter channel must finish flush with the edges of the sheets.the snaptite system allows adjustment for this process by simply tapping the channel along the sheets until each end is neatly flush. If you need to remove channels from the panels, pull the channel along the panel from opposing ends. You may need someone to help with this. 3mm POP RIVETS 4mm NUT & BOLT SET PAGE
Model: 33GK DOOR 6. DOOR PANEL ASSEMBLY 58C SNAP T TE i 58A 58B B A SNAP T TE i 58C ALL VERTICAL DOOR S ARE INSTALLED IN THE REVERSE DIRECTION IN COMPARISON TO HORIZONTAL DOOR S 0mm FLANGE B 5mm FLANGE ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 3
Model: 33GK REAR PANEL ASSEMBLY 30A 3A 54B 30A i SNAP T TE 8D i SNAP T TE SIDE PANEL ASSEMBLY ( Required) INSIDE OF SHED 36R 4D 83R 36L 5A 83L 8C ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 4
Model: 33GK ROOF PANEL ASSEMBLY ( Required) 49A 49A 49A 60B 86A x PRE-PUNCHED HOLES TO THIS END OF EACH SHEET WITH PART NO. 8C FITTED i SNAP T TE 8C i SNAP T TE 86A ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 5
Model: 33GK FRONT PANEL ASSEMBLY 89A 89B 3A 3A SNAP T TE 54A 90B SNAP i T TE i 79B i SNAP T TE 54C i SNAP T TE ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 6
Model: 33GK DOOR PANEL ASSEMBLY 9A B 9A B NOTE: NUTS AND BOLTS (SUPPLIED) MAY BE USED INSTEAD OF POP RIVETS (SUPPLIED) BY SIMPLY ENLARGING THE HINGE HOLE SETS IN THE JAMB USING A 4MM DRILL BIT NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment. position each hasp centrally over the padbolt shaft, and drill 3mm holes and secure with screws ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 7
Model: 33GK PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not positioned upside down. The top channel of each panel is pre-punched for attaching roof sheets, the bottom channels are not. SIDE WALL PANEL S FIT INTO THE NOTCHED FRONT AND REAR WALL PANEL S 97B TYPE 60B THIS END TYPE 8C THIS END ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 8
Model: 33GK ROOF CONSTRUCTION INSIDE VIEW OF FIXING SECURE PEAK BRACE TO RIDGE BEAM AND ROOF PANEL WITH ONE SCREW AT EACH END MOVE THE OTHER ROOF PANEL INTO POSITION AND SECURE PEAK BRACE TO RIDGE BEAM AND ROOF PANEL WITH ONE SCREW AT EACH END SLIDE THE ROOF PANEL INTO POSITION, AND SECURE WITH ONE SCREW AT EACH CORNER ONLY AT THIS STAGE ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 9
Model: 33GK FINAL CONSTRUCTION 4A BEND THE TOP AND BOTTOM FLANGES AS SHOWN, THEN HOOK THE BOTTOM FLANGES UNDER THE TOP AND SCREW THE TOP FLANGES FOR BOTH AS SHOWN GABLE CAPS ANCHORING OF SHED LOCATION OF CONCRETE ANCHORS - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE - DRILL A 0mm HOLE INTO THE WALL SHEET BOLT & NUT STEEL ANGLE WALL SHEET SLAB - DRILL A 0mm HOLE INTO THE CONCRETE DYNABOLT ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 33GK 0/07/7 PAGE 0