Liquid ring vacuum pumps in compact design SIHI extruvac LEME 13, LEME 155 Pressure range: Suction volume flow: 1 to 113 mbar 3 to 17 m³/h CONSTRUCTION TYPE SIHI liquid ring vacuum pumps are displacement pumps of uncomplicated and robust construction with the following particular features: non-polluting due to nearly isothermal compression oil-free, as no lubrication in the working chamber handling of nearly all gases and vapours able to handle water carry over easy maintenance and reliable operation low noise and nearly free from vibration wide choice of material, therefore applicable nearly everywhere shaft not contact with the medium protection against cavitation as standard incorporated dirt drain incorporated central drain no metallic contact of the rotating parts The SIHI liquid ring vacuum pumps LEME are single-stage ones. APPLICATION Handling and exhausting of dry and humid gases. The pumps are applied in all fields where a pressure of 1 to 9 mbar must be created by robust vacuum pumps. The LEME is specially designed to handle additional water that is exhaust through the suction inlet. NOTE During operation the pump must continuously be supplied with service liquid, normally water, in order to eliminate the heat resulting from the gas compression and to replenish the liquid ring, because part of the liquid is leaving the pump together with the gas. It is possible to reuse the service liquid. The pumps are equipped with a device by which the contaminated service liquid can continuously be drained during operation (dirt drain), if necessary. The direction of rotation is clockwise, when looking from the drive on the pump. GENERAL TECHNICAL DATA Pump type unit LEME 13 LEME 155 Speed 5 Hz 15 rpm 6 Hz 175 Max. compression over pressure bar.3 Max. admissible pressure difference bar 1.1 Hydraulic test (over pressure) bar 3 Moment of inertial of the rotating pump parts and of the water filling kg. m².53.69 Sound pressure level at a suction pressure of 15 mbar Max. gas temperature dry saturated db (A) Service liquid max. admissible temperature max. viscosity max. density C mm²/s kg/m³ 8 12 volume up to shaft level litre 2.8 3.2 Max. Water handle capability m 3 /h 7.5 The combination of several limiting values is not admissible. C C 65 2 1 VACUUMTECHNOLOGY LEME 133.7133.52.1 E /26
Material design Material design Item Components A 1.1 Vacuum casing.625 1.9 Central body 13.7 Guide disk 1. 23.5 Vane wheel impeller 2.196.1 3.3 Mechanical seal Cr-Steel / Carbon / Perbunan 75.11 Valve plate PTFE Sectional drawing LEME 13, LEME 155 Fresh water requirements in [m³/h] dependent on suction pressure, speed, mode of operation and difference in temperature suction pressure [mbar] 1 2 KB KB KB Pump type speed difference in temperature [ C] FB difference in temperature [ C] FB difference in temperature [ C] [rpm] 1 5 2 1 5 2 1 5 2 LEME 15.19.31.52.95.19.31.51.9.18.29.6.75 13 175.2.39.6.26..6.2.37.53 LEME 15.22.36.58.95.23.37.57.9.23.35.51.75 155 175.29..65.3.5.6.29.1.57 FB = fresh liquid service KB = combined liquid service with service water 1 C, 5 C, 2 C warmer than the fresh water. These values are valid without water handling capabilities. FB 2
Suction volume flow and power absorption LEME 13 1 12 Suction volume flow [m³/h] 1 8 6 15 rpm 2 1 2 3 5 6 7 8 9 1 5 Power adsorption [kw] 3 2 1 15 rpm 1 2 3 5 6 7 8 9 1 The operating data are applicable under the following conditions: pumping medium: - dry air: 2 C - water vapour saturated air: 2 C service liquid: - water: 15 C Compression pressure 113 mbar (atmospheric pressure) The suction volume flow is applied to the suction pressure Tolerance of the operating data 1% Max. fresh water need with lowest suction pressure Note: For different operating parameters, especially for additional water handling, the performance curve will change. Dependent on the used electric motor additional medium can be handled up to 7.5 m³/h. 3
Suction volume flow and power absorption LEME 155 18 16 1 Suction volume flow [m³/h] 12 1 8 6 15 rpm 2 1 2 3 5 6 7 8 9 1 6 Power adsorption [kw] 5 3 2 15 rpm 1 1 2 3 5 6 7 8 9 1 The operating data are applicable under the following conditions: pumping medium: - dry air: 2 C - water vapour saturated air: 2 C service liquid: - water: 15 C Compression pressure 113 mbar (atmospheric pressure) The suction volume flow is applied to the suction pressure Tolerance of the operating data 1% Max. fresh water need with lowest suction pressure Note: For different operating parameters, especially for additional water handling, the performance curve will change. Dependent on the used electric motor additional medium can be handled up to 7.5 m³/h.
Dimension table N 1 N 2 u B = gas inlet G 1 ½ = gas outlet G 1 ½ = connection for service liquid G ½ u e = drain connection G 3 / 8 u se = connection for dirt drain G 3 / 8 u m = connection for pressure gauge G 3 / 8 u m1 = connection for drain valve G 3 / 8 Electric motor IP 55 weight size kw f 1 f 2 h 1 h 2 h 3 h * m m 1 m 2 m 3 m m 5 n n 1 n 2 n 3 o 3 w* w 1 * appr. kg 5 Hz 6 Hz 112 M,8 32 51 6 LEME 13 215 165 15 112 M 5 6,2 112 15 28 5 176 1 28 2 225 19 25 521 68 22 58 3 112 M 5 6,2 232 182 538 78 LEME 155 162 132 M 6,7 8 272 222 132 18 32 88 218 178 32 278 55 256 216 276 26 62 92 other motors on request * dimensions dependent on the motor make ** see list of accessories 5
Data regarding the pump size - order hints Series & size Hydraulic & bearing Shaft sealing Material design Casing seal Hydraulic for additional water handling AAE mechanical seal, O-rings Perbunan A main parts of GG Liquid seal Z two grease lubricated antifriction bearings arranged in the motor LEME 13 LEME 155 Z AAE A Motor selection table Y-voltage motor enclosure IP 55 5 Hz -voltage power kw Y-voltage motor enclosure IP 55 6 Hz -voltage power kw size motor design. LEME 13 66-725 38-2, - -8,8 112 M BW LEME 13 66-725 38-2 5, - -8 6,2 112 M CW LEME 155 66-725 38-2 5, - -8 6,2 112 M BW LEME 155 66-725 38-2 6,7 - -8 8, 132 M CW Example for ordering: The construction size LEME 155 Z AAE A with 5 kw three-phase ac motor (5 Hz, V ) 15 rpm has the complete order number: LEME 155 Z AAE A BW For motors with different Voltage or frequencies please specify. Accessories Recommended accessories LEME 13 LEME 155 SIHI ball type non-return valve size weight G 1 ½ 1. kg Material design 776 / brass and NBR SIHI part no. 2 23 Support foot for motor size 112 M for motor size 132 M SIHI part no. 2 7 1-2 7 1 2 7 12 Spare parts Spare part kit LEME 13 LEME 155 Basic repair kit Consist of: mechanical seal, valve plate, sealing material, adjustment crew SIHI part no. 65751 65752 Any changes in the interest of the technical development are reserved. Sterling SIHI GmbH Lindenstraße 17, D-2552 Itzehoe, Germany Telephone: +9 () 8 21 / 7 71-1, Fax: +9 () 8 21 / 7 71-27 6