JPR-THEW Installation Instructions 1 GENERAL INFORMATION Your THIN Extension consists of a combination of Light Segments and Standoffs. It can be a single Light Segment with one Power Standoff and one End Standoff at either end, Or multiple Light Segments connected by Pass-Through Standoffs, with one Power Standoff and one End Standoff at either end. Installation Type Description Power Supply/Driver PLUG-IN pages 2-4, 8 REMOTE DRIVER DIRECT pages 2, 5, 8 For easy repositioning of fixture, requires nearby wall outlet. Includes: Remote control with wall mounted holder Wall mounted cord wrap The most minimal installation method. In-wall low voltage cable wired directly into the standoff. Class 2-24VDC 1.5A wall outlet adapter - dimmable via included remote control Class 2-24VDC remote driver - dimmable via compatible wall switch, refer to driver specifications Juniper recommends Lutron DVCL-253P dimmers for use with our Standard drivers IMPORTANT: TO PREVENT ELECTRIC SHOCK, ALWAYS DISCONNECT THE POWER BEFORE INSTALLING FIXTURE AND BEFORE CLEANING OR OTHER MAINTENANCE HARDWIRED FIXTURES SHOULD BE INSTALLED BY A LICENSED ELECTRICIAN - INSTALL ACCORDING TO NATIONAL ELECTRIC CODE AND LOCAL REGULATIONS CLASS 2 POWER SUPPLY REQUIRED
JPR-THEW Installation Instructions 2 24 Inch Light Segment (a1) PART GLOSSARY 36 Inch Light Segment (a2) Power Standoff (c1) Plug-in Power Standoff (c1) Pass-through Standoff (c2) End Standoff (c3) Standoff Bracket(b) OR Set Screw(f) #8 Pan Head (d) 8-32 Countersunk (g) Wire Nuts (n) #8 Countersunk (e) 8-32 Pan Head (h) PLUG-IN OPTIONAL PARTS Remote (j1) Remote Holder (j2) Cord Wrap (k1) Cord Wrap Mount (k2) MOUNTING DIAGRAM Use a level to mark the locations of the Standoff Brackets for your chosen Light Segment length. The fixture may be mounted horizontally or vertically according to your application. 24 inches (609.6mm) 36 inches (914.4mm)
JPR-THEW Installation Instructions 3 PLUG-IN INSTALLATION PLUG-IN STEP 1 Fix the Standoff Brackets (b) to the wall using supplied Screws (d) and appropriate anchors (if necessary). b d PLUG-IN STEP 2 Route the cord through one of three exit holes, then slip the Plug-in Power Standoff (c1) over the Standoff Bracket (b). Note: be sure to align the set screw holes on the Standff and Mounting Bracket. CORD WRAP STEP 1 Mark the mounting location of the Cord Wrap (k1), making sure that the cord runs tangentially to the inner post. c1 k1 CONTINUE TO PAGE 4
JPR-THEW Installation Instructions 4 PLUG-IN INSTALLATION CONTINUED CORD WRAP STEP 2 Using the supplied #8 Countersunk Screw (e) and/ or Drywall Anchor (i), fix the Cord Wrap Mount (k2) to the wall. CORD WRAP STEP 3 Thread the Cord Wrap (k1) onto the Cord Wrap Mount. e k2 CORD WRAP STEP 4 Making sure the cord coming from the fixture is taut, wrap it around the Cord Wrap, ensuring enough cord left to reach an outlet. REMOTE HOLDER STEP 1 Using supplied #8 Countersunk Screws (e) and Drywall Anchors (i)(if necessary), fix the Remote Holder (j2) to the wall. j2 e to 24VDC wall adaptor CONTINUE TO PAGE 6
JPR-THEW Installation Instructions 5 REMOTE DRIVER DIRECT INSTALLATION REMOTE DRIVER DIRECT STEP 1 Mount the Standoff Brackets (b) to the wall using the supplied Screws (d) and appropriate anchors (if necessary, additional blocking may be required to secure the bracket). Make sure to allow space for the 24VDC supply wires coming through the slot from the wall. d b + - REMOTE DRIVER DIRECT STEP 2 Using supplied Wire Nuts (n) make connection between the 24VDC supply wires and the fixture leads. Push the wire nuts into the Power Standoff (c1), and slide the Standoff over the Standoff Bracket. Note: be sure to align the set screw holes on the Standoff and Standoff Bracket. c1 NOTE: POWER MUST BE 24VDC CLASS 2, DO NOT CONNECT TO AC POWER/HOUSE WIRING Red(+) Black(-) CONTINUE TO PAGE 6
JPR-THEW Installation Instructions 6 FINAL INSTALLATION (PLUG-IN/REMOTE DRIVER DIRECT) FINAL INSTALLATION STEP 1 Slide the Light Segment (a1 or a2) into the mounted Standoff (either Pass-Through (c2) or End Cap (c3) depending on number of Light Segments). FINAL INSTALLATION STEP 2 Slide the next Standoff (c2 or c3, depending on number of Light Segments) onto the Light Segment. a1 or a2 c2 or c3 a1 or a2 c2 or c3 FINAL INSTALLATION STEP 3 Slide the Standoff (c2 or c3, depending on number of Light Segments) onto the Standoff Bracket. Repeat steps 1-3 for additional Light Segments. FINAL INSTALLATION STEP 4 For Plug-in and Remote Driver Direct installations, secure all installed Standoffs with supplied set screws (f). Note: you may gently rotate the Light Segment into the desired orientation with two hands, one at either end of the segment. a1 or a2 f c2 or c3
JPR-THEW Installation Instructions 7 CARE INSTRUCTIONS Like other natural metals, brass will patina over time, with the natural yellow hues intensifying over time. Juniper protects its brass with a mild matte lacquer to delay coloration of the metal, and to protect it from exposure to humidity and natural oils. In order to remove dirt, dust and fingerprints; gently wipe the lamp with a damp cloth. Do not use any chemical cleaning solutions; especially those containing ammonia, as this will damage the surface finish of the brass. Do not drop or apply excessive force on any part or joint of the lamp. Do not attempt to disassemble or modify it in any way except for recycling. Do not use the lamp for any purpose other than its intended use. Use indoors only. Please contact us should the lamp not operate as described, and we will be happy to assist you.