SECTION 1 FLUSH INSET INSTLLTION SECTION 2 STNDRD INSTLLTION 1/4" FRMED PNELS 3/4" OVERLY PNELS
OVERLL DIMENSIONS FLUSH INSET INSTLLTION 38" (96.5) 25 7/8" (65.7) 20 5/8" (52.4) 9 5/8" (24.4) * 8 (212.1) *73 1/4" (186.1) * 8 (212.1) SPECIFICTIONS Overall Width 38" (96.5 cm) Overall Height 8 (212.1 cm) Overall Depth 25 7/8" (65.7 cm) Clearance Cutout Width Cutout Height Cutout Depth Plumbing Requirements Shipping Weight 38 3/4" (98.4 cm) 39" (99.1 cm) 84 1/2" (214.6 cm) 26 3/16" (66.5 cm) 1/4" OD copper tubing or GE SmartConnect kit 640 lb (290.3 kg) *26" (66.0) FRONT VIEW *3 3/8" *3 3/8" (8.6) (8.6) SIDE VIEW * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84 ** llow 17" (43.2) min clearance for 115 door swing 35" (89.0) Case width Dimensions include 3/4" custom cabinet panel TTENTION ELECTRICIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n inidividual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. TOP VIEW 38 3/4" (98.4) ** llow 4" (10.2) min clearance to a wall for 90 door swing ** These refrigerators are equipped with a 2-position door stop. The factory-set 115 door swing can be adjusted to 90 if clearances to adjacent cabinets or walls is restricted. llow a 15" minimum clearance to wall for pan removal. If the 90 door stop position is used, pan access is maintained, but pan removal is restricted. Dimensions in parentheses are in centimeters unless otherwise noted. ctual product dimensions may vary due to manufacturing tolerances.
FLUSH INSET INSTLLTION 3/4" PNELS 84 1/2" (214.6) 26 3/16" (66.5) Flush inset depth 20 15/16" (53.2) Depth to cleat Finished cleats 5 1/4" (13.3) 3/4" (1.9) Width of side cleats 84" (214) height to cleat 3/4" TOP VIEW Case Finished cleats Case Trim 39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats ELEC. 10" (25.4) 6" (15.2) 24 3/4" (62.9) 1/2" (1.3) 75" (190.5 ) From floor to bottom of electrical area FLUSH INSET INSTLLTION Mounting the junction box in this location will also allow for front accessability through access panel. Water supply area. WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. W SIDE VIEW NTI-TIP RCKET 81 1/2" (207.0) SIDE VIEW INSTLLED WITH NTI-TIP RCKET Use two additional hole locations at end of brackets 7" (17.8) WTER (9.0) FRONT VIEW CL racket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs Wall Studs 7" (17.8) FRONT VIEW OF CUTOUT WITH NTI-TIP RCKET The information below applies to all installation constructions: wall bracket, bolts and toggles will be supplied with the unit. The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. In installation opening, measure 81 ½ from floor and draw a horizontal line. Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32.5 of installation opening to ensure 2 wall studs are penetrated. The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied L bolts. See Installation Instructions for detailed instructions.
FLUSH INSET 3/4" PNEL DIMENSIONS SINGLE INSTLLTION Grille Freezer Drawer C D PNEL SSEMLY CROSS SECTION HINGE CLERNCES ROUTER 1/4" DEEP X PNEL DIMENSIONS 1/4" Router Cut Depth for Hinge Clearance 3/4" Flush Inset PNEL SSEMLY CROSS SECTION C D 38" 9 5/8" 46 1/2" 22 5/16" FLUSH INSET 3/4" PNEL DIMENSIONS DUL INSTLLTION Y Z HINGE CLERNCE X Y Z 1 1/4" 1" 1/2" FLUSH INSET INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels. Fieldinstalled custom door and grille panels are required. djustment brackets allow 1/8 fine adjustment of panel position in 3 dimensions. Use templates provided to locate mounting brackets on the door and grille panels. Maximum total panel weight: food door panels 58 lbs. Freezer drawer panel 28 lbs. Grille panel 11 lbs Handles handles not included. Custom handles supplied by your cabinet maker may be used. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4 panels. Kit includes one handle 30 1/2 long. Order 2 kits from your Monogram supplier. ZKHCSS2: European tubular handle designed to fit 3/4 panels. Kit includes 2 handles. handle is 44 3/16 and drawer handle is 33 3/16". Order ZUGF2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. Grille HINGE CLERNCE X Y Z 1 1/4" 1" 1/2" E C HINGE CLERNCES ROUTER 1/4" DEEP Z Y X Freezer Drawer Freezer Drawer D PNEL DIMENSIONS C D E 74 1/8" 9 5/8" 46 1/2" 22 5/16" 36 15/16" PNEL SSEMLY CROSS SECTION 1/4" Router Cut Depth for Hinge Clearance 3/4" Flush Inset PNEL SSEMLY CROSS SECTION
DUL INSTLLTIONS FLUSH INSET INSTLLTION 3 7/8" (9.8) 75 1/8" (190.8) Finished Width 25 3/4" (65.4) 26 3/16" (66.5) Min. Cutout Depth 84 1/2" (214.6) Finished Opening ELEC. 5 1/2" ELEC. 5 1/2" 9" (22.9) (13.9) 9" (22.9) (13.9) separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product. In a side-by-side installation of a left-andright-hand door swing product, 1 1/2 clearance between the units is required. Order ZUGF2 custom panel unified grille kit for this installation. 75 1/2" (191.8 ) From floor to bottom of electrical area 7" (17.8) WTER (9.0) 5 3/4" (14.6) 5 3/4" (14.6) WTER (9.0) 7" (17.8) W FRONT VIEW SIDE VIEW DUL PRODUCT CLERNCES 25" (63.5) min To wall 1 1/2" (3.8) 25" (63.5) min To wall 130 swing 130 swing
OVERLL DIMENSIONS STNDRD INSTLLTION 25 1/4" (64.1) 36" (91.5) 23 7/8" (60.7) 9 7/8" (25.1) 1 7/8" (4.8) * 84" (213.4) 46 1/4" (117.5) *73 1/4" (186.1) * 8 (212.1) SPECIFICTIONS Overall Width Overall Height Overall Depth Clearance Cutout Width 36" (91.4 cm) 84" (213.4 cm) 25 3/8" (64.5 cm) 36 3/4" (93.4 cm) 35 1/2" (90.2 cm) Cutout Height 8-84 1/2" (212.1-214.6 cm) Cutout Depth Plumbing Requirements Shipping Weight 24" (61 cm) 1/4" OD copper tubing or GE SmartConnect kit 640 lb (290.3 kg) FRONT VIEW *24 1/8" (61.3) *26" (66.0) *26 1/2" (16.5) * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. ** llow 25" (63.5) min clearance for 130 door swing 35" 35" (89.0) Case width *3 5/8" (9.2) SIDE VIEW TTENTION ELECTRICIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n inidividual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. TOP VIEW 36 3/4" (93.4) ** llow 4" (10.2) min clearance to a wall for 90 door swing ** These refrigerators are equipped with a 2-position door stop. The factory-set 130 door swing can be adjusted to 90 if clearances to adjacent cabinets or walls is restricted. llow a 15" minimum clearance to wall for pan removal. If the 90 door stop position is used, pan access is maintained, but pan removal is restricted. Dimensions in parentheses are in centimeters unless otherwise noted. ctual product dimension may vary due to manufacturing tolerances.
STNDRD INSTLLTION STNDRD INSTLLTION 3 1/8" 24" (61) (7.93) 35 1/2" (90.2) 7/16" (1.1) 1 9/16" Trim overlap 2 5/16" (3.97) (5.874) SIDE VIEW NTI-TIP RCKET W 81 1/2" (207.0) SIDE VIEW INSTLLED WITH NTI-TIP RCKET *84 1/2" (214.6) *Trim will overlap additional 7/16" Use two additional hole locations at end of brackets ELEC. 5" (12.7) 10" (25.4) TOP VIEW 6" (15.24) WTER (9.0) 5" FRONT VIEW CL (12.7) racket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs Wall Studs 75" (190.5 ) From floor to bottom of electrical area FRONT VIEW OF CUTOUT WITH NTI-TIP RCKET Mounting the junction box in this location will also allow for front accessability through access panel. Water supply area. WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. The information below applies to all installation constructions: wall bracket, bolts and toggles will be supplied with the unit. The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. In installation opening, measure 81 ½ from floor and draw a horizontal line. Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32.5 of installation opening to ensure 2 wall studs are penetrated. The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied L bolts. See Installation Instructions for detailed instructions.
STNDRD 1/4" FRMED PNEL DIMENSIONS SINGLE INSTLLTION STNDRD INSTLLTION PNEL SSEMLY CROSS SECTION Grille C Supplied Handles Trim 1/4" Framed Trimmed refrigerators are designed to be customized with decorative panels. Fieldinstalled custom door and grille panels are required. 1/4 Framed s: Order trim kit #ZTKFLHH for 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Freezer Drawer D PNEL DIMENSIONS C D 1/4" Framed 33 7/8" 8 7/8" 46 1/16" 21 7/8" Maximum total panel weight: food door panel 58 lbs. Freezer drawer panel 28 lbs. Grille panel 11 lbs. STNDRD 3/4" OVERLY PNEL DIMENSIONS SINGLE INSTLLTION Grille Freezer Drawer C D PNEL SSEMLY CROSS SECTION 3/4" Overlay Supplied Handles PNEL DIMENSIONS C D 1/4" acker 33 7/8" 8 7/8" 46 1/16" 21 7/8".10" Spacer 32 1/2" 7 5/8" 44 11/16" 20 1/2" 3/4" Overlay 34 1/8" 9" 46 5/16" 22".25" +.10" +.75" = 1.10" Total Thickness Trim 1/4" acker.10" Spacer 3/4 Overlay s: Order trim kit #ZTKFLHH for 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. ssemble the panels with glue and screws. Screws must be countersunk into the backer panel. NOTE: Left-to-right offset is not always equal to top-to-bottom offset. Maximum total panel weight: food door panel 58 lbs. Freezer drawer panel 28 lbs. Grille panel 11 lbs. Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional Tubular Stainless Steel Handle designed to fit 3/4" overlay panels. ZKHCSS2: European tubular handle designed to fit 3/4 panels. Kit includes 2 handles. handle is 44 3/16 and drawer handle is 33 3/16".
CUSTOM SIDE PNELS F 1 7/8" (4.8) 24" (61.0) 3/16" (.5) *84 *84" (213.4) *Depending on installation height STNDRD INSTLLTION F Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4 side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer. *3" - 4" (7.6-10.2) *Depending on installation height 2 9/16" (6.5)
STNDRD 1/4" FRMED PNEL DIMENSIONS DUL INSTLLTION Freezer Drawer Grille E Freezer Drawer C D PNEL DIMENSIONS 1/4" Framed 69 7/8" 8 7/8" C 46 1/16" D 21 7/8" E 33 7/8" STNDRD INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels. Fieldinstalled custom door and grille panels are required. 1/4 Framed s: Order trim kit #ZTKFLHH for 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: food door panel 58 lbs. Freezer drawer panel 28 lbs. Grille panel 25 lbs. Order ZUG2: Unified grille kit for dual installation PNEL SSEMLY CROSS SECTION Trim Supplied Handles 1/4" Framed 3/4 Overlay s: STNDRD 3/4" OVERLY PNEL DIMENSIONS DUL INSTLLTION Freezer Drawer PNEL SSEMLY CROSS SECTION Grille E Freezer Drawer 3/4" Overlay Supplied Handles C D PNEL DIMENSIONS 1/4" acker.10" Spacer 3/4" Overlay 69 7/8" 68 1/2" 70 1/8" 8 7/8" 7 5/8" 9" C 46 1/16" 44 11/16" 46 5/16" D 21 7/8" 20 1/2" 22" E 33 7/8" 32 1/2" 34 1/8".25" +.10" +.75" = 1.10" Total Thickness Trim 1/4" acker.10" Spacer Order trim kit #ZTKFLHH for 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. ssemble the panels with glue and screws. Screws must be countersunk into the backer panel. NOTE: Left-to-right offset is not always equal to top-to-bottom offset. Maximum total panel weight: food door panel 58 lbs. Freezer drawer panel 28 lbs. Grille panel 25 lbs. Order ZUG2: Unified grille kit for dual installation Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional Tubular Stainless Steel Handle designed to fit 3/4" overlay panels. ZKHCSS2: European tubular handle designed to fit 3/4 panels. Kit includes 2 handles. handle is 44 3/16 and drawer handle is 33 3/16".
DUL INSTLLTIONS STNDRD INSTLLTION 2 5/16" (5.9) 8 min 84 1/2" max (212.1-214.6) Finished Opening 71 1/2" (181.6) Finished Width 24 3/16" (61.4) ELEC. 6" ELEC. 6" 10" (25.4) (15.2) 10" (25.4) (15.2) 75" (190.5 ) From floor to bottom of electrical area 24" (60.9) Min. Cutout Depth separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product. dditional cutout width may be required when side panels are used. In a side-by-side installation of a leftand-right-hand door swing product, 1 clearance between the units is required. Order ZUG2: custom panel unified grille kit for one continuous grille panel. 5" (12.7) WTER (9.0) 5 3/4" (14.6) 5 3/4" (14.6) WTER (9.0) 5" (12.7) 10" (25.4) WTER FRONT VIEW SIDE VIEW DUL PRODUCT CLERNCES 25" min (63.5) To wall 1" (2.5) 25" min (63.5) To wall 130 swing 130 swing
FETURES ND ENEFITS Custom ppearance - llows personalization with cabinet-compatible panels an custom handles Upfront Electronic Controls with Digital Readout - llows precise temperature settings and are positioned for maximum ease of use Humidity Controlled Vegetable Compartments and Sealed Snack Pans - Help maintain freshness and help preserve foods longer djustable, Spill Proof Glass Shelves - Make it easy to customize storage to handle foods and containers of various sizes 2 Sealed Deli Pans with Full-Extension Slides Six djustable ins - Offer added storage flexibility GE Water Filtration System - Delivers clean, great tasting ice R