Drift Master Installation Manual Tech Support: 800.332.4094 Option 2 2072 Alton Parkway. Irvine, CA 92606 Website: Lagunatools.com Copyright 2017 Laguna Tools, Inc. Laguna is a registered trademark of Laguna Tools, Inc.
Hardware A. Main Bracket (2) B. Table nut (2) C. Table Bolt (2) D. Fence Bolt (2) E. Washer (4) F. Nut (2) Note: Please make sure that all of the mounting hardware is accounted for. Note: Inspect all parts for defects prior to assembly. Note: Ruler included in package may not fit on all bandsaws. Some modification may be necessary.
Installation **There are three techniques for mounting the fence. Please review all three prior to mounting and choose the best method for your saw** Installing the brackets to the table (Technique 1)
1. Using hardware (B), (C) and (E) mount the main brackets (A) to the bandsaw table. See figure 1.1 & 1.2 Figure 1.1 Figure 1.2 Note: You may need to enlarge the current holes in your table. They should be ½ to accept the bolt provided.
2. Mount fence bolt (D) using hardware (E) and (F). Do not fully tighten nut (F) yet. See figure 2.1 & 2.2 Figure 2.1 Figure 2.2
Note: Prior to mounting the fence rail choose the stud holes in the rail that are best suited for your bandsaw. You should have four sets of holes to choose from. Note: To utilize the full throat of the saw use the rail holes that will allow the crank handle to be as far left of the saw frame as possible. This will also allow the bottom door enough clearance to open. 3. Mount fence using a 19mm socket wrench to tighten bolt (D). The bolt should be fully engaged into the fence rail to ensure proper seating. Figure 3.1
Note: Adjust height of drift master on brackets so the fence rides on the bandsaw table surface. 4. Adjust bolts (D) in bracket slots until drift master fence rides on bandsaw table. Tighten nuts (F) once this is done. 5. Tighten all hardware.
Installing entire fence with brackets already attached (Technique 2) 1. Attach brackets using supplied hardware. Note: Do not tighten nut (F) 2. Fully seat bolt (D) into rail. This will enable you to tighten nut (F) without the use of a wrench on bolt (D) once fence is mounted to saw. 3. Attach entire unit to saw. 4. Adjust fence and tighten hardware.
Installing without the use of brackets (Technique 3) 1. Remove the original fence system, figure 1.1 Figure 1.1 Figure 1.2 Drill and tap for ruler End of ruler must not protrude past blade slot 2. Drill and tap holes for the ruler indicated in figure 1.2. Note: hole placement will vary from one machine to another. Drill ½ holes in bandsaw table for fence studs. Hole location may vary depending on size of table. Match rail studs to holes Hole placement from top of table to center of hole is 38mm. Holes may need to be elongated.
Adjustments To adjust the drift on the drift master loosen the top handles, figure 2.1 Figure 2.1 Figure 2.2 Turn bottom knob till desire adjustment is achieved then tighten handles. 2.2 Move the quick release to lock and unlock the screw mechanism. This will allow free movement of the fence for large adjustments in unlocked position.
B50.01.00.00.00 RIP FENCE WITH FINE MOVING 1 В50.01.00.00.04 ALUMINUM PROFILE 1 2 DIN 985 NUT М 12 4 3 DIN 125 A WASHER АМ12 4 4 В50.01.00.00.02 STUD 2 5 В50.01.00.00.05 COTTER 1 6 GN603-78-М10-DGN HANDLE М10 2 7 DIN 134 WASHER M10 2 8 В50.01.00.00.06 RIM 1 9 DIN 134 WASHER M 8 2 10 GN603-63-М8-45-DGN HANDLE М8Х45 2 11 В50.01.00.00.07 CENTERING STUD 1 12 В50.01.00.00.03 SLIDE BLOCK FOR FENCE 1 13 GN603-63-М8-40-DGN HANDLE М8Х40 1 14 В50.01.00.00.08 STRIP FOR ADJUSTING 1 15 В50.01.00.00.01 BEAM 1 16 DIN 985 NUT М 12 2 17 DIN 134 WASHER М12 2 18 B50.01.10.00.01 STRIP FOR DISC 1 19 DIN 7991 SCREW М10Х25 2 20 B50.01.10.00.05 DISK FOR ROTATING 1 21 DIN 934 NUT М8 1
22 ART.139-60-8.5 HANDLE 8.5 1 23 DIN 912 SCREW М 8Х65 1 24 DIN 439 NUT М12 LOW 1 25 TAB. T1144 PLATE 1 26 B50.01.10.00.07 BUSHING 1 27 В50.01.00.00.09 ECCENTRIC 1 28 ISO 7380 SCREW М 6Х10 2 29 B50.01.10.00.03 NUT 1 30 DIN 603 SCREW М8X25 1 31 B50.01.10.00.04 ROTATING STRIP 1 32 DIN 134 WASHER M 8 1 33 DIN 315 FLYING NUT M8 1 34 DIN 125 A WASHER АМ12 1 35 DIN 7991 SCREW М 8Х16 2 36 B50.01.10.00.02 SUPPORT STRIP 1 37 DIN 555 NUT М10 1 38 ~DIN 933 BOLT POLYAMIDE М10Х30 1 39 B50.01.10.00.08 L-SHAPE ALUMINUM 1 40 RULER RIGHT-LEFT 0-500 1 41 B50.01.10.00.09 STRIP 1 42 B50.01.10.00.06 SCREW М12 1
2072 Alton Parkway. Irvine, CA 92606 Ph: 800.234.1976 www.lagunatools.com Laguna Tools is not responsible for errors or omissions. Specifications subject to change. Machines may be shown with optional accessories. 2017, Laguna Tools, Inc. LAGUNA and the LAGUNA Logo are the registered trademarks of Laguna Tools, Inc. All rights reserved.