The Future of Analog IC Technology MP48 A, 8V Synchronous Rectified Step-Down Converter DESCRIPTION The MP48 is a monolithic synchronous buck regulator. The device integrates two 30mΩ MOSFETs, and provides A of continuous load current over a wide input voltage of 4.75V to 8V. Current mode control provides fast transient response and cycle-by-cycle current limit. An adjustable soft-start prevents inrush current at turn-on, and in shutdown mode the supply current drops to µa. This device, available in an 8-pin SOIC package, provides a very compact solution with minimal external components. FEATURES A Output Current Wide 4.75V to 8V Operating Input Range Integrated 30mΩ Power MOSFET Switches Output Adjustable from 0.93V to 5V Up to 93% Efficiency Programmable Soft-Start Stable with Low ESR Ceramic Output Capacitors Fixed 340kHz Frequency Cycle-by-Cycle Over Current Protection Input Under Voltage Lockout 8 Pin SOIC APPLICATIONS Distributed Power Systems Networking Systems FPGA, DSP, ASIC Power Supplies Green Electronics/ Appliances Notebook Computers MPS and The Future of Analog IC Technology are Registered Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION PUT 7 8 EN SS GND 4 MP48 BS COMP 6 3 5 EFFICIENCY (%) Efficiency vs Load Current 00 95 V = 3.3V 90 85 V =.5V 80 75 70 65 60 55 50 0 0.5.0.5.0.5 LOAD CURRENT (A) MP48 Rev.. www.monolithicpower.com
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER ORDERG FORMATION Part Number Package Top Marking Free Air Temperature (T A ) MP48DS* SOIC8 MP48DS -40 C to 85 C MP48DN** SOIC8E MP48DN -40 C to 85 C *For Tape & Reel, add suffix Z (e.g. MP48DS Z); For RoHS Compliant Packaging, add suffix LF (eg. MP48DS LF Z) ** For Tape & Reel, add suffix Z (eg. MP48DN Z); For RoHS Compliant Packaging, add suffix LF (eg. MP48DN LF Z) PACKAGE REFERENCE TOP VIEW TOP VIEW BS 8 SS BS 3 8 7 6 SS EN COMP GND 3 4 7 6 5 EN COMP GND 4 5 EXPOSED PAD ON BACKSIDE CONNECT TO GND SOIC8 ABSOLUTE MAXIMUM RATGS () Supply Voltage V...-0.3V to 0V Switch Node Voltage V... V Boost Voltage V BS...V 0.3V to V 6V All Other Pins...-0.3V to 6V Junction Temperature...50 C Continuous Power Dissipation (T A = 5 C) () SOIC8..38W SOIC8E.5W Lead Temperature...60 C Storage Temperature... -65 C to 50 C Recommended Operating Conditions (3) Input Voltage V...4.75V to 8V Output Voltage V...0.93V to 5V Operating Junct. Temp (T J )...-40 C to 85 C SOIC8E Thermal Resistance (4) θ JA θ JC SOIC8... 90... 45... C/W SOIC8E... 50... 0... C/W Notes: ) Exceeding these ratings may damage the device ) The maximum allowable power dissipation is a function of the maximum junction temperature T J (MAX), the junction-toambient thermal resistance θ JA, and the ambient temperature T A. The maximum allowable continuous power dissipation at any ambient temperature is calculated by P D (MAX)=(T J (MAX)-T A )/ θ JA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage.. 3) The device is not guaranteed to function outside of its operating conditions. 4) Measured on JESD5-7, 4-layer board. MP48 Rev.. www.monolithicpower.com
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER ELECTRICAL CHARACTERISTICS V = V, T A = 5 C, unless otherwise noted. Parameter Symbol Condition Min Typ Max Units Shutdown Supply Current V EN = 0V 3.0 μa Supply Current V EN =.0V; V =.0V.3.5 ma Feedback Voltage V 4.75V V 8V 0.900 0.93 0.946 V Feedback Overvoltage Threshold. V Error Amplifier Voltage Gain (5) A EA 400 V/V Error Amplifier Transconductance G EA ΔI C = ±0μA 800 μa/v High-Side Switch On Resistance (5) R DS(ON) 30 mω Low-Side Switch On Resistance (5) R DS(ON) 30 mω High-Side Switch Leakage Current V EN = 0V, V = 0V 0 μa Upper Switch Current Limit Minimum Duty Cycle.4 3.4 A Lower Switch Current Limit From Drain to Source. A COMP to Current Sense Transconductance GCS 3.5 A/V Oscillation Frequency F osc 305 340 375 KHz Short Circuit Oscillation Frequency F osc V = 0V 00 KHz Maximum Duty Cycle D MAX V =.0V 90 % Minimum On Time (5) 0 ns EN Shutdown Threshold Voltage V EN Rising..5.0 V EN Shutdown Threshold Voltage Hysteresis 0 mv EN Lockout Threshold Voltage..5.7 V EN Lockout Hysterisis 0 mv Input Under Voltage Lockout Threshold V Rising 3.80 4.0 4.40 V Input Under Voltage Lockout Threshold Hysteresis 0 mv Soft-Start Current V SS = 0V 6 μa Soft-Start Period C SS = 0.μF 5 ms Thermal Shutdown (5) 60 C Note: 5) Guaranteed by design, not tested. MP48 Rev.. www.monolithicpower.com 3
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER P FUNCTIONS SOIC8 Pin # SOIC8E Pin # BS 3 3 Name Description 4 4 GND Ground. 5 5 6 6 COMP 7 7 EN 8 8 SS High-Side Gate Drive Boost Input. BS supplies the drive for the high-side N- Channel MOSFET switch. Connect a 0.0μF or greater capacitor from to BS to power the high side switch. Power Input. supplies the power to the IC, as well as the step-down converter switches. Drive with a 4.75V to 8V power source. Bypass to GND with a suitably large capacitor to eliminate noise on the input to the IC. See Input Capacitor. Power Switching Output. is the switching node that supplies power to the output. Connect the output LC filter from to the output load. Note that a capacitor is required from to BS to power the high-side switch. Feedback Input. senses the output voltage to regulate that voltage. Drive with a resistive voltage divider from the output voltage. The feedback threshold is 0.93V. See Setting the Output Voltage. Compensation Node. COMP is used to compensate the regulation control loop. Connect a series RC network from COMP to GND to compensate the regulation control loop. In some cases, an additional capacitor from COMP to GND is required. See Compensation Components. Enable Input. EN is a digital input that turns the regulator on or off. Drive EN high to turn on the regulator, drive it low to turn it off. Pull up with 00kΩ resistor for automatic startup. Soft-Start Control Input. SS controls the soft start period. Connect a capacitor from SS to GND to set the soft-start period. A 0.μF capacitor sets the soft-start period to 5ms. To disable the soft-start feature, leave SS unconnected. MP48 Rev.. www.monolithicpower.com 4
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER TYPICAL PERFORMANCE CHARACTERISTICS V = V, V O = 3.3V, L = 0µH, C = 0µF, C = µf, T A = 5 C, unless otherwise noted. Steady State Test V = V, V = 3.3V I = 0A, I = 8.mA Startup through Enable V = V, V = 3.3V I = A (Resistance Load) Shutdown through Enable V = V, V = 3.3V I = A (Resistance Load) V 0mV/div. V EN 5V/div. V EN 5V/div. V 0mV/div. V V/div. V V/div. A/div. A/div. A/div. V 0V/div. V 0V/div. ms/div. V 0V/div. ms/div. Heavy Load Operation Medium Load Operation Light Load Operation A Load A Load No Load V, AC 00mV/div. V, AC 00mV/div. V, AC 0mV/div. V O, AC 0mV/div. V O, AC 0mV/div. V O, AC 0mV/div. A/div. A/div. A/div. V 0V/div. V 0V/div. V 0V/div. Short Circuit Protection Short Circuit Recovery Load Transient V V/div. V V/div. V 00mV/div. A/div. A/div. A/div. OAD A/div. MP48 Rev.. www.monolithicpower.com 5
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER OPERATION FUNCTIONAL DESCRIPTION The MP48 is a synchronous rectified, current-mode, step-down regulator. It regulates input voltages from 4.75V to 8V down to an output voltage as low as 0.93V, and supplies up to A of load current. The MP48 uses current-mode control to regulate the output voltage. The output voltage is measured at through a resistive voltage divider and amplified through the internal transconductance error amplifier. The voltage at the COMP pin is compared to the switch current measured internally to control the output voltage. The converter uses internal N-Channel MOSFET switches to step-down the input voltage to the regulated output voltage. Since the high side MOSFET requires a gate voltage greater than the input voltage, a boost capacitor connected between and BS is needed to drive the high side gate. The boost capacitor is charged from the internal 5V rail when is low. When the MP48 pin exceeds 0% of the nominal regulation voltage of 0.93V, the over voltage comparator is tripped and the COMP pin and the SS pin are discharged to GND, forcing the high-side switch off. SS.V 0.3V 0.93V -- -- -- OVP ERROR AMPLIFIER OSCILLATOR 340KHz RAMP CLK -- S R CURRENT COMPARATOR CURRENT SENSE AMPLIFIER Q Q -- 5V BS COMP EN --.5V.5V -- EN OK LOCK COMPARATOR SHUTDOWN COMPARATOR.V OVP < 4.V TERNAL REGULATORS GND Figure Functional Block Diagram MP48 Rev.. www.monolithicpower.com 6
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER APPLICATIONS FORMATION COMPONENT SELECTION Setting the Output Voltage The output voltage is set using a resistive voltage divider from the output voltage to pin. The voltage divider divides the output voltage down to the feedback voltage by the ratio: R V = R R Where V is the feedback voltage and V is the output voltage. Thus the output voltage is: R R V = 0.93 R R can be as high as 00kΩ, but a typical value is 0kΩ. Using the typical value for R, R is determined by: R = 0.83 (V 0.93) (kω) For example, for a 3.3V output voltage, R is 0kΩ, and R is 6.kΩ. Inductor The inductor is required to supply constant current to the output load while being driven by the switched input voltage. A larger value inductor will result in less ripple current that will result in lower output ripple voltage. However, the larger value inductor will have a larger physical size, higher series resistance, and/or lower saturation current. A good rule for determining the inductance to use is to allow the peak-to-peak ripple current in the inductor to be approximately 30% of the maximum switch current limit. Also, make sure that the peak inductor current is below the maximum switch current limit. The inductance value can be calculated by: V L = fs ΔIL V Where V is the output voltage, V is the input voltage, f S is the switching frequency, and Δ is the peak-to-peak inductor ripple current. Choose an inductor that will not saturate under the maximum inductor peak current. The peak inductor current can be calculated by: V P = ILOAD fs L V Where OAD is the load current. The choice of which style inductor to use mainly depends on the price vs. size requirements and any EMI requirements. Optional Schottky Diode During the transition between high-side switch and low-side switch, the body diode of the lowside power MOSFET conducts the inductor current. The forward voltage of this body diode is high. An optional Schottky diode may be paralleled between the pin and GND pin to improve overall efficiency. Table lists example Schottky diodes and their Manufacturers. Table Diode Selection Guide Part Number Voltage/Current Rating Vendor B30 30V, A Diodes, Inc. SK3 30V, A Diodes, Inc. MBRS30 30V, A International Rectifier Input Capacitor The input current to the step-down converter is discontinuous, therefore a capacitor is required to supply the AC current to the step-down converter while maintaining the DC input voltage. Use low ESR capacitors for the best performance. Ceramic capacitors are preferred, but tantalum or low-esr electrolytic capacitors may also suffice. Choose X5R or X7R dielectrics when using ceramic capacitors. Since the input capacitor (C) absorbs the input switching current it requires an adequate ripple current rating. The RMS current in the input capacitor can be estimated by: I C = I LOAD V V V V MP48 Rev.. www.monolithicpower.com 7
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER The worst-case condition occurs at V = V, where I C = OAD /. For simplification, choose the input capacitor whose RMS current rating greater than half of the maximum load current. The input capacitor can be electrolytic, tantalum or ceramic. When using electrolytic or tantalum capacitors, a small, high quality ceramic capacitor, i.e. 0.μF, should be placed as close to the IC as possible. When using ceramic capacitors, make sure that they have enough capacitance to provide sufficient charge to prevent excessive voltage ripple at input. The input voltage ripple for low ESR capacitors can be estimated by: ILOAD V V Δ = V C fs V V Where C is the input capacitance value. Output Capacitor The output capacitor is required to maintain the DC output voltage. Ceramic, tantalum, or low ESR electrolytic capacitors are recommended. Low ESR capacitors are preferred to keep the output voltage ripple low. The output voltage ripple can be estimated by: V Δ = RESR f S L V 8 fs C Where C is the output capacitance value and R ESR is the equivalent series resistance (ESR) value of the output capacitor. In the case of ceramic capacitors, the impedance at the switching frequency is dominated by the capacitance. The output voltage ripple is mainly caused by the capacitance. For simplification, the output voltage ripple can be estimated by: V ΔV = 8 fs L C V In the case of tantalum or electrolytic capacitors, the ESR dominates the impedance at the switching frequency. For simplification, the output ripple can be approximated to: ΔV = R fs L V ESR The characteristics of the output capacitor also affect the stability of the regulation system. The MP48 can be optimized for a wide range of capacitance and ESR values. Compensation Components MP48 employs current mode control for easy compensation and fast transient response. The system stability and transient response are controlled through the COMP pin. COMP pin is the output of the internal transconductance error amplifier. A series capacitor-resistor combination sets a pole-zero combination to control the characteristics of the control system. The DC gain of the voltage feedback loop is given by: V A VDC = RLOAD GCS A EA V Where A VEA is the error amplifier voltage gain; G CS is the current sense transconductance and R LOAD is the load resistor value. The system has two poles of importance. One is due to the compensation capacitor (C3) and the output resistor of the error amplifier, and the other is due to the output capacitor and the load resistor. These poles are located at: f f P P GEA = π C3 A = π C R VEA LOAD Where G EA is the error amplifier transconductance. The system has one zero of importance, due to the compensation capacitor (C3) and the compensation resistor (R3). This zero is located at: f Z = π C3 R3 The system may have another zero of importance, if the output capacitor has a large capacitance and/or a high ESR value. The zero, due to the ESR and capacitance of the output capacitor, is located at: f ESR = π C R ESR MP48 Rev.. www.monolithicpower.com 8
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER In this case (as shown in Figure ), a third pole set by the compensation capacitor (C6) and the compensation resistor (R3) is used to compensate the effect of the ESR zero on the loop gain. This pole is located at: f P 3 = π C6 R3 The goal of compensation design is to shape the converter transfer function to get a desired loop gain. The system crossover frequency where the feedback loop has the unity gain is important. Lower crossover frequencies result in slower line and load transient responses, while higher crossover frequencies could cause system instability. A good rule of thumb is to set the crossover frequency below one-tenth of the switching frequency. To optimize the compensation components, the following procedure can be used.. Choose the compensation resistor (R3) to set the desired crossover frequency. Determine the R3 value by the following equation: π C fc π C 0. fs R 3 = < GEA GCS V GEA GCS V Where f C is the desired crossover frequency which is typically below one tenth of the switching frequency.. Choose the compensation capacitor (C3) to achieve the desired phase margin. For applications with typical inductor values, setting the compensation zero, f Z, below one-forth of the crossover frequency provides sufficient phase margin. Determine the C3 value by the following equation: 4 C3 > π R3 f C 3. Determine if the second compensation capacitor (C6) is required. It is required if the ESR zero of the output capacitor is located at less than half of the switching frequency, or the following relationship is valid: π C R f < S ESR If this is the case, then add the second compensation capacitor (C6) to set the pole f P3 at the location of the ESR zero. Determine the C6 value by the equation: C RESR C6 = R3 External Bootstrap Diode An external bootstrap diode may enhance the efficiency of the regulator, and it will be a must if the applicable condition is: V is 5V or 3.3V, and duty cycle is high: D= >65% V In these cases, an external BST diode is recommended from the output of the voltage regulator to BST pin, as shown in Figure. MP48 BST External BST Diode 448 CBST L C 5V or 3.3V Figure Add Optional External Bootstrap Diode to Enhance Efficiency The recommended external BST diode is 448, and the BST cap is 0.~µF. Where R3 is the compensation resistor. MP48 Rev.. www.monolithicpower.com 9
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER TYPICAL APPLICATION CIRCUIT PUT 7 8 EN SS GND 4 MP48 BS COMP 6 3 5 Figure 3 MP48 with 3.3V Output, µf/6.3v Ceramic Output Capacitor MP48 Rev.. www.monolithicpower.com 0
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER PCB LAY GUIDE PCB layout is very important to achieve stable operation. It is highly recommended to duplicate EVB layout for optimum performance. If change is necessary, please follow these guidelines and take Figure 4 for reference. ) Keep the path of switching current short and minimize the loop area formed by input cap, high-side MOSFET and low-side MOSFET. PUT 4.75V to 8V ) Bypass ceramic capacitors are suggested to be put close to the Vin Pin. 3) Ensure all feedback connections are short and direct. Place the feedback resistors and compensation components as close to the chip as possible. 4) Route away from sensitive analog areas such as. 5) Connect,, and especially GND respectively to a large copper area to cool the chip to improve thermal performance and long-term reliability. C5 C R4 7 EN 8 SS GND MP48 BS COMP 3 5 L R PUT C4 4 6 C3 R3 D (optional) R C MP48 Typical Application Circuit Top Layer Bottom Layer Figure 4 MP48 Typical Application Circuit and PCB Layout Guide MP48 Rev.. www.monolithicpower.com
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER PACKAGE FORMATION 0.89(4.80) 0.97(5.00) 8 5 SOIC8E (EXPOSED PAD) 0.4(3.5) 0.36(3.45) P ID 0.50(3.80) 0.57(4.00) 0.8(5.80) 0.44(6.0) 0.089(.6) 0.0(.56) 4 TOP VIEW BOTTOM VIEW SEE DETAIL "A" 0.03(0.33) 0.00(0.5) 0.05(.30) 0.067(.70) SEATG PLANE 0.000(0.00) 0.006(0.5) 0.050(.7) BSC SIDE VIEW 0.0075(0.9) 0.0098(0.5) FRONT VIEW 0.00(0.5) 0.00(0.50) x 45o GAUGE PLANE 0.00(0.5) BSC 0.04(0.6) 0.063(.60) 0.050(.7) 0 o -8 o 0.06(0.4) 0.050(.7) DETAIL "A" 0.38(3.5) 0.03(.6) RECOMMENDED LAND PATTERN 0.3(5.40) NOTE: ) CONTROL DIMENSION IS CHES. DIMENSION BRACKET IS MILLIMETERS. ) PACKAGE LENGTH DOES NOT CLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. 3) PACKAGE WIDTH DOES NOT CLUDE TERLEAD FLASH OR PROTRUSIONS. 4) LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMG) SHALL BE 0.004" CHES MAX. 5) DRAWG CONFORMS TO JEDEC MS-0, VARIATION BA. 6) DRAWG IS NOT TO SCALE. MP48 Rev.. www.monolithicpower.com
MP48 A, 8V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER PACKAGE FORMATION SOIC8 0.89(4.80) 0.97(5.00) 8 5 0.04(0.6) 0.063(.60) 0.050(.7) P ID 0.50(3.80) 0.57(4.00) 0.8(5.80) 0.44(6.0) 0.3(5.40) 4 TOP VIEW RECOMMENDED LAND PATTERN 0.03(0.33) 0.00(0.5) 0.050(.7) BSC 0.053(.35) 0.069(.75) SEATG PLANE 0.004(0.0) 0.00(0.5) SEE DETAIL "A" 0.0075(0.9) 0.0098(0.5) FRONT VIEW SIDE VIEW 0.00(0.5) 0.00(0.50) x 45o NOTE: GAUGE PLANE 0.00(0.5) BSC 0 o -8 o 0.06(0.4) 0.050(.7) DETAIL "A" ) CONTROL DIMENSION IS CHES. DIMENSION BRACKET IS MILLIMETERS. ) PACKAGE LENGTH DOES NOT CLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. 3) PACKAGE WIDTH DOES NOT CLUDE TERLEAD FLASH OR PROTRUSIONS. 4) LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMG) SHALL BE 0.004" CHES MAX. 5) DRAWG CONFORMS TO JEDEC MS-0, VARIATION AA. 6) DRAWG IS NOT TO SCALE. NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP48 Rev.. www.monolithicpower.com 3