OVERALL DIMENSIONS 36" (91.5) 25 3/4" (65.4) 23 7/8" (60.7) 2 3/4" (7.0) *84" (213.4) *73 1/4" (186.1) *8 (212.1) 64 1/4" (163.2) SPECIFICATIONS Overall Width Overall Height Overall Depth Door Clearance 36" (91.4 cm) 84" (213.4 cm) 25 3/4" (65.41 cm) 36 3/4" (93.4 cm) *6 1/2" (16.5) FRONT VIEW * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. * SIDE VIEW Cutout Width 35 1/2" (90.2 cm) Cutout Height 8-84 1/2" (212.1-214.6 cm) Cutout Depth 24" (61 cm) 3 (89.0) Case width Plumbing Requirements Shipping Weight 1/4" OD copper tubing or GE SmartConnect kit 569 lb ** Allow 2 (63.5) min clearance for 130 door swing ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. TOP VIEW 36 3/4" (93.4) ** Allow 4" (10.2) min clearance to a wall for 90 door swing **These units are equipped with a 2-position door stop. The factory set 130 door swing can be adjusted to 90 if clearance to adjacent cabinets or walls is restricted. Allow 1 minimum clearance to wall for pan removal. If the 90 door stop position is used, pan access is maintained but pan removal is restricted. Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimension may vary due to manufacturing tolerances.
STANDARD INSTALLATION 2 5/16" (5.9) *8 min *84 1/2" max (212.1-214.6) *Trim will overlap additional 7/16" ELEC. ANTI-TIP BRACKET 35 1/2" (90.2) A 5 1/2" (14.0) B SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET 81 1/2" (207.00) 75 1/2" (191.8) From floor to bottom of electrical area Use two additional hole locations at end of brackets 4" (10.2) 7/16" (1.1) 2" Trim overlap (5.1) CL Screws mounted into vertical wall studs Make sure holes selected are centered on the studs Wall Studs W FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET A Mounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area. WARNING: The freezer is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. The information below applies to all installation constructions: A wall bracket, bolts and toggles will be supplied with the unit. The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. In installation opening, measure 81. from floor and draw a horizontal line. Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32. of installation opening to ensure 2 wall studs are penetrated. The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied L bolts. See Installation Instructions for detailed instructions.
CUSTOM SIDE PANELS F 1 7/8" (4.8) 3/16" (.5) *84" (213.4) *Depending on installation height F Side panels must be used whenever the sides of the freezer will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the freezer with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer. *3"- 4" (7.6-10.2) *Depending on installation height 2 9/16" (6.5)
DUAL INSTALLATIONS 2 5/16" (5.9) 8 min 84 1/2" max (212.1-214.6) Finished Opening 71 1/2" (181.6) Finished Width 24 3/16" (61.4) ELEC. 5 1/2" ELEC. 5 1/2" (13.9) FRONT VIEW DUAL PRODUCT CLEARANCES 2 (63.5) min 1" (2.5) A (13.9) 2 (63.5) min 75 1/2" (191.8 ) From floor to bottom of electrical area 2" min (5.1) Min. Cutout Depth SIDE VIEW W 1 (38.1) min A A separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product. Additional cutout width may be required when side panels are used. B In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required. Order ZUGSS2 European, ZUGPP2 Professional or ZUG2 custom panel unified grille kit for one continuous grille panel. C In a side-by-side installation with same door swing, allow 2" minimum clearance between the products to prevent the door swing interference. Allow 1 minimum to a wall to achieve full drawer extension and pan removal. Additional clearances are required when using custom panels and handles. NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel kits will not fit this installation. D In a side-by-side installation with right and left door hinges together, allow minimum clearance between the two products to prevent one door from striking the other. Additional clearances required when using custom panels and handles. NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel kits will not fit this installation. 130 Door swing 130 Door swing B min C D Product Specification Revised 1/18
FEATURES AND BENEFITS INTEGRATED APPEARANCE WITH PREMIUM- GRADE STAINLESS STEEL - Extending across the door and wrapping beautifully around the edges; A Monogram signature, slim tubular handle enhances the overall look ENHANCED TEMPERATURE MANAGEMENT SYSTEM - With precise electronic controls and thermistors, maintains ideal storage conditions for frozen foods CONCEALED ICE DRAWER - Provides quick and easy access to filtered ice GE FILTRATION SYSTEM - Provides clean, fresh-tasting water to the freezer's icemaker ADJUSTABLE, WIRE SHELVES, GALLON-SIZE DOOR BINS AND PULLOUT BASKETS - Allow customizable storage for foods and containers of varying sizes CONCEALED HALOGEN LIGHTING SYSTEM - Illuminates contents without compromising space R