Product Bulletin Uncooled mini-dil Pump Module 1200 Series The JDS Uniphase 1200 Series 980 nm uncooled pump module simplifies next-generation erbium doped fiber amplifier (EDFA) designs by eliminating the need for larger, less efficient, and costlier electrical supplies. It is wavelength stabilized by a fiber Bragg grating (FBG), which maintains stable performance over temperature ranges of -5 to 75 C and power ranges of 20 to 200 mw. The 1200 Series pump module incorporates the JDS Uniphase 6560 laser diode for unmatched performance and reliability at high temperatures and power levels, while remaining locked to the FBG wavelength over a wide dynamic range. By eliminating the thermoelectric cooler, nextgeneration EDFA designs - particularly the thermal and control circuitry - benefit from the 1200 Series pump module's smaller size and lower power consumption. Key Features High power: up to 200 mw, BOL Low power dissipation Miniature Dual-In-Line (Mini-DIL) form factor -5 to 75 C operating range Polarization maintaining (PM) fiber Applications SDH/Single channel EDFAs Small form factor amplifiers Gain blocks Receiver pre-amplifiers Compliance Telcordia GR-468-CORE
Pump Module 2 Dimensions Diagram (Specifications in mm unless otherwise noted.) 30.21 NOM. POINT A 750 NOM. TO C/L OF GRATING 13.21 500 NOM. TO C/L OF SPLICE 4 3 2 1 7.37 4 5 1 8 3.80 5 6 7 8 LASER FLEXIBLE 400 MICRON RECOAT 1.60 STRAIN RELIEF 400 MICRON SPLICE RECOAT (IF APPLICABLE) FIBER LENGTH 1500 MEASURED FROM POINT A 4.10±0.25 8X 8.60 2.17 8X 0.41 LEAD WIDTH 8X 0.25 LEAD THICKNESS 6X 2.54 LEAD SPACING Pinout Pin Description 1 No connection 2 Package ground 3 No connection 4 No connection 5 No connection 6 Laser diode cathode 7 Laser diode anode 8 No connection
Pump Module 3 Absolute Maximum Ratings Parameter Symbol Test Condition Minimum Maximum Operating case temperature Top - -20 C 75 C Storage temperature Tstg 72 hours -40 C 85 C LD reverse voltage Vr 25 C - 2 V LD reverse current 25 C - 10 µa Ex-fiber power All temperatures, 1 hour cumulative - 260 mw Electrostatic discharge (ESD) VESD C = 100 pf, R = 1.5 Ω, human body model - 1000 V Fiber axial pull force 3 x 10 seconds - 5 N Fiber side pull force 3 x 10 seconds - 2.5 N Fiber bend radius - 16 mm - Relative humidity RH 40 C 5% 95% Lead soldering time 260 C - 10 seconds Operating Powers Product Code Operating Power Pop Current at Power Pop Iop Kink-Free Power Pmax Current at Power Pmax Imax 12-xxxx-100 80 mw 270 ma 100 mw 340 ma 12-xxxx-120 100 mw 320 ma 120 mw 395 ma 12-xxxx-140 115 mw 360 ma 140 mw 440 ma 12-xxxx-160 130 mw 395 ma 160 mw 485 ma 12-xxxx-180 150 mw 445 ma 180 mw 545 ma 12-xxxx-200 165 mw 485 ma 200 mw 600 ma 12-xxxx-220 180 mw 525 ma 220 mw 655 ma 12-xxxx-240 200 mw 580 ma 240 mw 715 ma Available Wavelength Selection (Tgrating = 23±3 C, unless otherwise noted) Product Code Minimum Wavelength Maximum Wavelength 12-8000-xxx 970 nm 985 nm 12-7402-xxx 973 nm 975 nm 12-7602-xxx 975 nm 977 nm
Pump Module 4 Electro-Optical Performance (BOL, Tgrating = 23±3 C, unless otherwise noted) Parameter Symbol Test Condition Minimum Maximum Threshold current Ith - - 55 ma Forward current Iop Pf = Pop - See Operating Powers table Forward voltage Vf I f = Iop - 2.2 V Operating power Pop I f = Iop See Operating Powers table Kink-free power Pkink I f = Imax See Operating Powers table Center wavelength λm Pmin to Pmax See Available Wavelength Selection table Spectral bandwidth λm Pmin to Pmax - 2 nm Side mode suppression SMSR Pmin to Pmax 10 db - Total module power dissipation PDiss_Tot I f = Iop BOL, Pf 100 mw - 0.6 W I f = Iop EOL,Pf 100 mw - 0.8 W I f = Iop BOL, Pf 165 mw - 0.9 W I f = Iop EOL,Pf 165 mw - 1.2 W I f = Iop BOL, Pf 200 mw - 1.1 W I f = Iop EOL,Pf 200 mw - 1.4 W Operating Conditions Parameter Symbol Minimum Maximum Operating case temperature -5 C 75 C Return reflection - -50 db Fiber bend radius 20 mm - Minimum operating power Pmin 20 mw - Ordering Information For more information on this or other products and their availability, please contact your local JDS Uniphase account manager or JDS Uniphase directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at sales@jdsu.com. Sample: 12-7402-100 12- - Code Wavelength 7402 973 to 975 nm 7602 975 to 977 nm 8000 970 to 985 nm Code Kink-Free Power 100 100 mw 120 120 mw 140 140 mw 160 160 mw 180 180 mw 200 200 mw 220 220 mw 240 240 mw
Pump Module 5 User Safety Safety and Operating Considerations Labeling 21 CFR 1040.10 Compliance The laser light emitted from this laser diode is invisible and may be harmful to the human eye. Avoid looking directly into the fiber when the device is in operation. CAUTION: THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT INCREASES EYE HAZARD. Because of the small size of these devices, the output power and laser emission indicator label shown below is attached to the individual shipping container. All labels are illustrated here to comply with 21 CFR 1040.10 as applicable under the Radiations Control for Health and Safety Act of 1968. 8-PIN MODULE LABEL Operating the laser diode outside of its maximum ratings may cause device failure or a safety hazard. Power supplies used with this component cannot exceed maximum peak optical power. CW laser diodes may be damaged by excessive drive current or switching transients. When using power supplies, the laser diode should be connected with the main power on and the output voltage at zero. The current should be increased slowly while monitoring the laser diode output power and the drive current. Careful attention to heatsinking and proper mounting of this device is required to ensure specified performance over its operating life. To maximize thermal transfer to the heatsink, the heatsink mounting surface must be flat to within.001. 01/31/03 12-AAC863X 12-xxxx-xxx SHIPPING BOX LABEL Serial: Model: 12-AAC863X 12-XXXX-XXX OUTPUT POWER AND LASER EMISSION INDICATOR LABEL DANGER INVISIBLE LASER RADIATION - AVOID DIRECT EXPOSURE TO BEAM PEAK POWER 500 mw WAVELENGTH 630-1,550 nm INVISIBLE LASER DIODE AVOID EXPOSURE JDS Uniphase 3530 Bassett St Santa Clara, CA 95054 TEL: 408-943-4202 FAX: 408-943-4252 01/31/03 ESD PROTECTION Electrostatic discharge (ESD) is the primary cause of unexpected laser diode failure. Take extreme precaution to prevent ESD. Use wrist straps, grounded work surfaces, and rigorous antistatic techniques when handling laser diodes. CAUTION - Handle with care. Easily damaged by electrostatic discharge This product complies with 21 CFR Chapter 1, Subchapter J CLASS 3B LASER PRODUCT Visible/invisible radiation emitted from fiber end or fiber receptacle Telcordia is a registered trademark of Telcordia Technologies Incorporated. North America toll-free: 1-800-498-JDSU (5378) Worldwide toll-free: +800-5378-JDSU www.jdsu.com All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. The user assumes all risks and liability whatsoever in connection with the use of a product or its application. JDS Uniphase reserves the right to change at any time without notice the design, specifications, function, fit or form of its products described herein, including withdrawal at any time of a product offered for sale herein. JDS Uniphase makes no representations that the products herein are free from any intellectual property claims of others. Please contact JDS Uniphase for more information. JDS Uniphase and the JDS Uniphase logo are trademarks of JDS Uniphase Corporation. Other trademarks are the property of their respective holders. Copyright JDS Uniphase Corporation. All rights reserved. 10143035 Rev. 003 09/03