Instruction Sheet VDM-200-T Tilt Wall Mount THANK YOU Thank you for purchasing the VDM-200-T tilt wall mount. Please read these instructions thoroughly before installing or assembling this product. PRODUCT FEATURES Up to 15 degrees of limitless tilt Post-install leveling mechanism enables quick micro-adjustment of horizontal plane of display Safety locking features keep the display securely mounted VESA Capability 75x75mm - 200x200mm I-00808 Rev A
IMPORTANT SAFETY INSTRUCTIONS / INSTRUCTIONS IMPORTAANTES SUR LA SÉCURITÉ SAVE ALL INSTRUCTIONS / CONSERVER CES INSTRUCTIONS WARNING/AVERTISSEMENT and the exclamation point within an equilateral triangle is intended to alert the user to the possibility of serious injury or death if the instructions are not followed. Avertissement et le point d'exclamation dans un triangle équilatéral est destiné à alerter l'utilisateur de la possibilité de blessures graves ou la mort si les instructions ne sont pas suivies. CAUTION/ATTENTION and the exclamation point within an equilateral triangle is intended to alert the user to the possibility of damaging or destroying the equipment if the instructions are not followed. Attention et le point d'exclamation dans un triangle équilatéral est destiné à alerter l'utilisateur de la possibilité d'endommager ou de détruire l'équipement si les instructions ne sont pas suivies. WARNING: Failure to read, understand and follow the following information can result in serious personal injury, damage to the equipment or voiding of the warranty. AVERTISSEMENT: Ne pas lire, comprendre et suivre les informations suivantes peut entraîner des blessures graves, des dommages à l'équipement ou de la nullité de la garantie. WARNING: Failure to provide correct structural strength for the component may result in serious personal injury or damage the equipment. The 2x4 stud wall to which the component is being attached may have a maximum drywall thickness of 5/8 (1.6 cm). AVERTISSEMENT: Le défaut de fournir une résistance structurelle correcte pour le composant peut entraîner des blessures graves ou endommager l'équipement. Le goujon de 2x4 auquel le composant mur est connecté peut avoir un maximum de 1.6 cm (5/8 ) d'épaisseur cloison sèche. WARNING: Exceeding the weight capacity may result in personal injury or equipment damage. The combined weight of all components attached to the mount must not exceed weights listed on page 3. AVERTISSEMENT: Dépasser la capacité de poids peut entraîner des blessures ou des dommages matériels. Le poids combiné de tous les composants reliés au support de montage ne doit pas dépasser les grammages indiqués à la page 3. WARNING: Be aware of pinch points and do not place fingers in between moving parts. AVERTISSEMENT: Soyez conscient des points de pincement et de ne pas placer les doigts entre les pièces mobiles. WARNING: Use this product for its intended use and only use attachments recommended by the manufacturer. AVERTISSEMENT: Utilisez ce produit pour son utilisation prévue et utiliser uniquement les accessoires recommandés par le fabricant. WARNING: Do not use a damaged product. Return damaged products to a qualified service center for repair. AVERTISSEMENT: Ne pas utiliser un produit endommagé. Retour produits endommagés à un centre de service qualifié pour la réparation. WARNING: Not intended for outdoor use. AVERTISSEMENT: Non destiné à une utilisation en extérieur. Page 2
WEIGHT RATINGS Model VDM-200-T Weight Rating 80 lbs. Maximum Total Rated Load TOOLS REQUIRED #2 Phillips Screwdriver Drill Protective Eyewear 5/32 Wood Bit or 3/8 Masonary Bit Level Hammer 3/8 Hex Socket 4mm Hex Key (Supplied) WARNING: Use tools with caution and follow all necessary safety protocols. AVERTISSEMENT: Utiliser des outils avec prudence et suivre tous les protocoles de sécurité nécessaires. Page 3
SUPPLIED COMPONENTS (1) Wall Mount Bracket (A) (1) Display Mount (B) (3) #14 x 2.5 Hex Head Screw (C) (3) Wall Anchor (D) M5 Washer (E) M8 Washer (F) M6 Spacer (G) (1) 4mm Hex Key (J) Display Mount Screws M4 x 12 (H-A) M4 x 20 (H-B) M5 x 30 (H-D) M5 x 12 (H-C) M6 x 12 (H-E) M6 x 20 (H-F) M6 x 30 (H-J) M8 x 16 (H-H) M8 x 20 (H-J) Page 4
WOOD STUD WALL BRACKET INSTALLATION 1. Determine height for display and find center of stud closest to desired position on wall. 2. Using a level, scribe a 4 long line down the center of the stud. (FIGURE A) FIGURE A 3. Using the wall mount bracket (A) as a template, mark the center of the 3 mounting holes along the scribed center line. (FIGURE B) Mounting holes A (FIGURE B) 4. Remove Wall Mount Bracket and using a 5/32 drill bit, drill a 2.5 deep pilot hole in each of the three marked center points. Page 5
WOOD STUD WALL BRACKET INSTALLATION CONT. 1) Install wall mounting bracket using (3x) supplied #14 x 2.5 hex head screws, orienting bracket as shown. (FIGURE C) NOTE: Flange must face up. C A FIGURE C BLOCK OR CEMENT WALL BRACKET INSTALLATION 1. Determine the desired position height for display on wall and using a level, scribe a 4 long line down the the concrete or block wall. (FIGURE D) FIGURE D Page 6
BLOCK OR CEMENT WALL BRACKET INSTALLATION CONT. 2. Using the Wall Mount Bracket (A) as a template, mark the center of the 3 mounting holes along the scribed center line. (FIGURE E) Mounting holes Wall Mounting Bracket (A) FIGURE E 3. Remove Wall Mount Bracket and using a 3/8 drill bit, drill a 2.5 deep hole in each of the 3 marked center points. 4. Press a wall anchor (D) into each drilled hole (Wall Anchors may require a hammer to install) (FIGURE F) 5. Install Wall Mounting Bracket (A) using (3x) #14 x 2.5 hex head screws (C), oriented bracket as shown. To prevent anchors from stripping, only use a hand tool to install screws. (FIGURE G) NOTE: Wall anchors may require a hammer to install. NOTE: To prevent anchors from stripping, only use a hand tool to install. A Flange must face up. D C FIGURE F FIGURE G Page 7
FLUSH DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied (4x) display mount screws, select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw. If supplied screws are still too long, use supplied spacers to take up slack. 2. Align display mount (B) with mounting holes on the back of display. Using (4x) washers (E or F) and (4x) display mount screws (H-A - H-J) to secure the display mount to your display. (FIGURE H) H-A - H-J E or F B FIGURE H Page 8
RECESSED OR RAISED DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied (4x) display mount screws (H-A - H-J), select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw. If supplied screws are still too long, use supplied spacers to take up slack. 2. Align display mount (B) with mounting holes on the back of display. Using (4x) washers (E or F), (4x) display mount screws (H-A - H-J) and (4x) spacer (G) to secure the display mount to your display. (FIGURE J) G H-A - H-J E or F B FIGURE J Page 9
RECESSED DISPLAY MOUNT BRACKET INSTALLATION 1. Align tabs on display mount with holes in wall bracket and slide down to lock into place. (FIGURE K) FIGURE K 2. Tighten security screw down into wall plate to lock display into place. (FIGURE L) FIGURE L Page 10
ADJUSTING DISPLAY TILT 1. To tilt display, loosen (3x) adjustment screws with supplied hex key (J), then grab top and bottom of display and carefully pull top of display gently to desired angle. Once display is at desired angle, tighten adjustment screws to lock in position. 2. To return display to a vertical position, loosen 3 adjustment screws with supplied hex key (J), then grab top and bottom of display and carefully push monitor from the top. Once display is vertical, tighten adjustment screws to lock in position. Tilt Adjustment Screw Tilt Adjustment Screws J +15 /-5 Page 11
WARRANTY For warranty information, refer to www.middleatlantic.com/terms. Corporate Headquarters Corporate Voice: 973-839-1011 - Fax: 973-839-1976 / International Voice: +1 973-839-8821 Fax: +1 973-839-4982 www.middleatlantic.com - info@middleatlantic.com Middle Atlantic Canada Voice: 613-836-2501 - Fax: 613-836-2690 ca.middleatlantic.com - customerservicecanada@middleatlantic.ca Factory Distribution USA: NJ - CA - IL Canada: ON - BC At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company. Page 12