Adjustable Wall Mount and Adjustable Mobile Stand for the PolyVision PJ920 Ultra-Short Throw Projector. Installation Guide

Table of contents Overview... 3 Important considerations... 3 Adjustable Wall Mount considerations... 3 Tools and supplies... 5 What comes in the box... 5 Projector components... 5 Lift system components... 6 ēno interactive whiteboard components... 7 Mobile stand components... 7 Adjustable Wall Mount required items... 8 Adjustable Mobile Stand required items... 8 Prepare the lift system for mounting... 9 Prepare the gas spring... 9 Secure the brake handle... 9 Raise the lift system... 10 Fasten the gas spring to the lift system... 10 Mount the lift system... 13 Adjustable mobile stand assembly... 13 Assemble the legs... 13 Add the lift system to the assembled legs... 14 Adjustable Wall Mount installation... 16 Position the wall mounting brackets... 16 Backer board installation... 17 Fasten mounting brackets to the wall... 17 Fasten the lift system to the wall... 18 Mount the projector... 19 Connect cables to the projector... 19 Assemble the projector and projector bracket... 19 Cable routing options... 20 Add the Height Adjustable bracket to the lift system turret... 20 Fasten the projector to the lift system... 21 Cable routing... 22 Install the ēno interactive whiteboard... 24 Fasten ēno interactive whiteboard mounting brackets to the lift system... 24 Fasten the ēno interactive whiteboard to the lift system... 25 Power on the projector and add the magnetic icon strip to the whiteboard... 26 Projector adjustment and driver installation... 27 Troubleshooting projector focus and alignment... 27 Focus... 27 Image size... 27 Image location (left to right)... 28 Image tilt... 29 Image squareness (up and down)... 29 Image location (up and down)... 30 Final check... 30 Install the PolyVision Driver Projector Add-in... 31 Appendix 1: Backer board installation... 32 TOOLS REQUIRED:... 32 PARTS/MATERIALS REQUIRED:... 33 Index... 38 2 Installation and Operation Guide

Overview Congratulations on your purchase of the PolyVision ēno one solution. This manual describes how to install the both the PolyVision ēno one Adjustable Wall Mount and Adjustable Mobile Stand solution for the PolyVision ultra-short throw projector only. Important considerations The following table provides the total weights of each installation option described in this manual: Installation option Adjustable Wall Mount ēno 2610 ēno 2810 Adjustable Mobile Stand ēno 2610 ēno 2810 Total Pounds (kg) 200 (91) 221 (100) 260 (118) 281 (128) Two people are recommending for this installation. The maximum allowable projector weight is 20 pounds (9 kg). No modifications or additions are to be made to the system beyond what is provided by PolyVision. Do not hang from or climb on any part of the ēno one Adjustable Wall Mount or Adjustable Mobile Stand. Tighten all screws securely using torque specifications where provided. Adjustable Wall Mount considerations Be sure to leave adequate spacing between ceilings, junction box and architectural elements to allow unobstructed vertical movement of the ēno one Adjustable Wall Mount. PolyVision 3

CAUTION FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. Read the entire Assembly Direction before beginning installation or assembly. Building construction varies greatly and is outside PolyVision s control. The Building s Engineer of record is responsible for the design of studs, backing, reinforcement, supporting members etc. which the units are attached to and must verify the adequacy of the mounting hardware. These instructions and any hardware provided by PolyVision are for convenience only and are not an indication of what may be required by your local Code. The building owner or designated agent is responsible for verifying that the installation is in compliance with all local Codes and regulations. If you have a problem, question, or request, call your local dealer or PolyVision at 800.620.POLY (7659) 4 Installation and Operation Guide

Tools and supplies What comes in the box Projector components 1 Remote control and batteries 2 USB cable 3 Power cable 4 VGA cable 5 Projector icon strip 6 Ultra-short throw projector PolyVision 5

Lift system components 1 Projector bracket 2 Wall bracket (not used for adjustable wall mount or mobile stand) 3 Height Adjustable bracket 4 Lift system wall brackets (x3) 5 Lift system 6 Gas spring 7 Corrugated cable manager 8 Hardware bags: Allen wrenches, cable ties, 5/16-18 bolts (x14), 10-24 nylon nuts and bolts (x4), thumb screws (x3) 9 Quick start guide 6 Installation and Operation Guide

ēno interactive whiteboard components 1 Wall mounting brackets (x2) 2 Fasteners (x4) 3 ēno interactive whiteboard 4 Icon strip 5 Accessory kit Mobile stand components 1 L-shaped Left front leg with castor 2 U-shaped rear leg with castors 3 L-shaped Right front leg with castor 4 Laptop/keyboard tray 5 Bottom tray PolyVision 7

Adjustable Wall Mount required items x6 #2 x6 Drill bit (determine based on hardware required by local code ) Bubble level Stud finder Step ladder Drill and drill bit Measuring tape (6) Wall anchors / fasteners determined by local code (not included in hardware kit) Optional: Backer board for use where wood studs are not on 16 centers. Adjustable Mobile Stand required items #2 Step ladder Drill #2 drill bit 8 Installation and Operation Guide

Prepare the lift system for mounting Prepare the gas spring 1. Remove the 13 mm and 10 mm locking pins located at each end of the gas spring sockets and retain them for later use. Note: Notice that the locking pins for each end of the gas spring are unique and be prepared to replace them in a later step. Secure the brake handle To secure the lift system brake handle: 1. Expose the open side of the lift system. 2. Rotate the brake handle 90 degrees to the in-use position. *Torque: 50-70 lb in (5-8 Nm) 10-15 lb 5/16 x 18 x 1/2 3. Fasten the handle in place using two 5/16 x 18 x 1/2 self-locking screws, one per brake handle arm (Allen wrench provided in the hardware kit). PolyVision 9

Raise the lift system To raise the lift system to its maximum height: 1. Rotate the lift system brake handle upward to release the brake and extend the lift system to its maximum height. Fasten the gas spring to the lift system To fasten the gas spring to the lift system: 1. Insert the gas spring through the opening in the lift system so that the larger black cylinder and larger (13 mm) socket is oriented with the 13 mm ball stud on the lift system carriage. 10 Installation and Operation Guide

4. Align the larger (13 mm) socket at the top of the gas spring with the ball joint on the upper rear of the lift system tubular support. If necessary, lift the brake handle to release the brake and adjust the lift system to align the ball and socket. 5. Press the ball and socket together until fully seated. Moderate pressure is needed. 6. Align the socket at the bottom of the gas spring with the ball joint on the lower front of the lift system. If necessary, lift the brake handle to release the brake and adjust the lift system to align the ball and socket. 7. Press the ball and socket together until fully seated. Moderate pressure is needed. PolyVision 11

8. Replace the locking pins on gas spring sockets at both ends, with the larger locking pin applied to the cylinder and the smaller locking pin to the rod end of the gas spring. Note: Avoid contacting the gas spring push rod with hard objects capable of scratching, such as tools or rings. Damage to the gas spring will reduce lift system life and will void the product warranty. 12 Installation and Operation Guide

Mount the lift system This section describes how to mount the lift system on the mobile stand or on a structural wall. Adjustable mobile stand assembly Assemble the legs To assemble the mobile stand legs: 1. Slide one arm of the U-shaped back leg (with casters) over the short coupler tube located at the rear of one of the L-shaped vertical legs (with locking casters) front leg. Note: Assure that the L-shaped vertical legs are oriented as shown below. 2. Align the pre-drilled and threaded screw hole in the L-shaped vertical leg with the one on the arm of the U-shaped back leg. 3. Fasten with one 5/16 x 18 x 1/2 self locking screw using moderate torque (Allen wrench provided in the hardware kit). Final torque will be applied in a later step. 4. Repeat for the other L-shaped vertical leg. 5. Place the assembled legs in a horizontal position with the locking casters of the L-shaped legs resting on the floor. 6. Hook the rear edge of the bottom tray over the top portion of the U-shaped leg section. 7. Rotate the tray until tray mounting holes make contact with underside of L-shaped leg section. PolyVision 13

8. Fasten the tray to the under side of the L-shaped front leg using two 5/16 x 18 x 1/2 self locking screw with moderate torque (Allen wrench provided in the hardware kit). Final torque will be applied in a later step. Add the lift system to the assembled legs To add the lift system to the assembled legs: 1. Release the brake handle and raise the lift system to its maximum height. 2. Place the lift system on the floor with the open side facing the floor. 3. Tilt up the bottom of the lift system to a 20 degree angle and support it in that position using, for example, packing material from the inner pack. 4. Slide the vertical arms of the mobile stand into the 2.5 openings on each side of the lift system. 5. Align the four screw holes on the rear of lift system with the threaded screw holes in the mobile stand L-shaped vertical legs. 6. Fasten the lift system to the mobile stand using four 5/16 x 18 x1/2 self locking screw with moderate torque (Allen wrench provided in the hardware kit). 14 Installation and Operation Guide

7. Tighten all 5/16 x 18 x 1/2 self locking screws to a torque of 10-15 lb ft (5-8 Nm). U-shaped leg section to vertical L-shaped legs (x2) Bottom tray to underside of L-shaped legs (x2) Lift system to mobile stand (x4) Caution: Confirm that the front castors are locked and taped to aid tilting the Adjustable Mobile Stand to the upright position. The mobile stand and lift system together weigh 145 pounds (66 kg). Use caution to avoid shocking the rear casters and over-rotating the system as you raise it. 8. With an assistant, raise the mobile stand and lift system assembly to the vertical position. 9. To support a laptop or keyboard from the rear of the Adjustable Mobile Stand, hang the laptop tray from the louver in the back of the lift system which provides the best ergonomic conditions for the user. Use the laptop tray s elastic cords to secure the laptop, chargers, and excess cabling. 10 Proceed to Mount the projector on page 19. PolyVision 15

Adjustable Wall Mount installation CAUTION FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. Read the entire Assembly Direction before beginning installation or assembly. Building construction varies greatly and is outside PolyVision s control. The Building s Engineer of record is responsible for the design of studs, backing, reinforcement, supporting members etc. which the units are attached to and must verify the adequacy of the Mounting hardware. These instructions and any hardware provided by PolyVision are for convenience only and are not an indication of what may be required by your local Code. The building owner or designated agent is responsible for verifying that the installation is in compliance with all local Codes and regulations. If you have a problem, question, or request, call your local dealer or PolyVision at 800.620.POLY (7659) Position the wall mounting brackets To position the wall brackets: 1. Choose a location on the wall free of architectural obstacles (fire alarm / suppression, junction boxes, low ceilings) with convenient access to: computer and projector connections power source 2. If installing on a sheetrock wall, use a stud finder to locate and mark the position of the wood wall studs: Studs must be on 16 centers. If studs are not on 16 centers, you can proceed only if you install a backer board on the wall first. Refer to Backer board installation on page 17. WARNING: The total lift system with projector and interactive whiteboard weighs roughly 221 pounds (100 kg). If installing on a sheetrock wall, all three wall mounting brackets must be fastened to stud 16 Installation and Operation Guide

centers with appropriate mounting hardware. If mounting on a cinder block brick wall, assure that no drill hole location aligns with mortar joints. Consult local building code authority for minimum anchoring requirements. Failure to do so could result in personal injury. 3. Measure and mark a line that is: 56 (1422 mm) from the floor for a finished board height of 32 (813 mm) from the floor (industry standard for lower elementary) 60 (1524 mm) from the floor for a finished board height of 36 (914 mm) from the floor (industry standard for upper elementary) 40lbs 19kg 40lbs 19kg 40lbs 19kg 60 (1524mm) ABC 56 (1422.4mm) 70lbs 32kg 16 (406mm) 70lbs 32kg 16 (406mm) 70lbs 32kg 4. Measure and mark three plumb vertical lines on 16 centers (centered on wood studs if applicable). 5. Use the mounting brackets as a template to carefully mark two mounting-hole locations on each of the three vertical lines (six hole locations total) by aligning the 90 degree flange on the wall mounting bracket with the horizontal level line centered on the plumb vertical lines. Backer board installation If installing on a sheet rock wall where wooden studs are not on 16 centers, you must install a backer board on the wall prior to installing the Adjustable Wall Mount. To install a backer board, refer to Appendix 1 on page 32. Fasten mounting brackets to the wall To fasten the wall mounting brackets to the wall: 1. Bolt the three wall mounting brackets to the wall using fasteners appropriate to your wall condition and ensuring that the brackets are on 16 centers. PolyVision 17

Fasten the lift system to the wall To fasten the lift system to the wall: 1. With the help of an assistant, hook the up turned tabs of the three wall mounting brackets through complimentary slots along lower edge of lift system. 2. Rotate the lift system flush to wall mount brackets 3. Align screw-hole locations on the right angle flange at the top of the three wall mounting brackets with corresponding holes in the lift system. 4. Fasten the lift system to the wall mounting brackets using three 5/16 x 18 x 1/2 self-locking screws with a torque of 10-15 lb ft (5-8 NM) (Allen wrench provided in the hardware kit). 18 Installation and Operation Guide

Mount the projector Connect cables to the projector 1. Connect the power, USB and VGA cable to the back of the projector as shown below. Assemble the projector and projector bracket To assemble the projector and projector bracket: 1. Install the long 4mm screw through the projector bracket and projector. PolyVision 19

2. Install two short 4mm screws directly through the projector bracket into the projector. Cable routing: Cables should pass through the top of the projector as shown. Add the Height Adjustable bracket to the lift system turret To add the Height Adjustable bracket to the lift system turret: 1. Pull the pin on the base of the turret and lower the bracket cylinder into the lift system turret. 20 Installation and Operation Guide

Fasten the projector to the lift system To fasten the projector to the lift system: 1. Hook the projector bracket into the bottom of the Height Adjustable bracket. 2. Fasten the projector bracket to the Height Adjustable bracket using two 5/16 screws. PolyVision 21

Cable routing To route cables: 1. Route the projector VGA, power, and USB cables (provided with the projector) through the turret as shown below. 2. Pull the pivot pin on the turret base and pass projector cables through the turret base. 3. Cover cabling below the turret base with 48 (1200 mm) of the split corrugated conduit provided. 22 Installation and Operation Guide

4. Pass conduit-covered cables through the elliptical cable hole at the top and bottom of the lift system, extending cabling through the lift system to desired power and data terminations. NOTE: Route the cabling between the gas spring and brake rod and the rear of ēno interactive whiteboard. 5. Lock the corrugated conduit into the key hole in the lift system to secure the cable bundle in position. 6. As local codes allow, stow excess cable by retaining it within the lift system. Use care to ensure that projector cables do not make contact with the gas spring and brake rod when the lift system rises and lowers. PolyVision 23

Install the ēno interactive whiteboard Fasten ēno interactive whiteboard mounting brackets to the lift system To install the ēno mounting brackets to the lift system: 1. Fasten the two mounting brackets (provided with the ēno interactive whiteboard) to the lift system using two #10 Allen bolts with #10 self-locking nuts per bracket provided in the hardware kit. #10-24 x 1/2" NOTE: Recesses in the rear of the lift system brackets prevent the #10 self-locking nuts from turning during installation to eliminate the need for wrenches. 24 Installation and Operation Guide

Fasten the ēno interactive whiteboard to the lift system To fasten the ēno interactive whiteboard to the lift system: 1. With the help of an assistant, lift the board and hang it from the wall brackets, as shown. 2. Assure that the ēno interactive whiteboard is centered about the projector turret to within +/-1/16 (2 mm). 3. Fasten the interactive whiteboard to the upper edge of the wall brackets using the four #8 selfdrilling screws provided in the hardware kit. PolyVision 25

Power on the projector and add the magnetic icon strip to the whiteboard To power on the projector: 1. Connect the projector power cord to an AC outlet. 2. Affix the two magnetic icon strips to the interactive whiteboard for interactive whiteboard control and for projector control. 3. Install batteries provided in the remote control. 4. Press the power button on the remote control. 26 Installation and Operation Guide

Projector adjustment and driver installation Troubleshooting projector focus and alignment Once the projector is powered on and warmed up, a PolyVision splash screen appears automatically on the ēno interactive whiteboard. The following steps describe how to adjust the focus and position of the splash screen if necessary. For best image quality, it is recommended that digital projector settings not be altered unless mechanical adjustments below fail to provide acceptable image placement and clarity. See projector user manual for digital image adjustment details. NOTE: Projector should be level, square to the interactive whiteboard surface, and set to Fill Mode (the default setting) prior to attempting the following adjustments. By design, ēno 2810 will not fully fill across the width of the board. There will be a vertical margin measuring approximately 2.5 (63 mm) to either side of the projected image. HINT: Hold a piece of white paper at the projected image border, slightly overlapping with the image to better define image boundary. A ¼ (6 mm) overlap of projected image on to projection surface trim often yields a favorable image fit. Focus To adjust the splash screen focus: 1. Use the manual focus adjustment found on the front of the projector (should not be required for most installations). Image size To adjust the splash screen size: 1. Loosen the three M4 screws in the top of the projector 2. Slide the projector away from the board to make the image larger; slide the projector toward the board to make the image smaller. PolyVision 27

3. Tighten the three M4 screws in the top of the projector. Image location (left to right) Limited side-to-side adjustment is available on the projector bracket. In some cases, it may be necessary to slide the whiteboard to one side and re-install the #8 x 1/2 screws. To adjust the splash screen location from left to right: 1. Loosen the 5/16 screws at the projector bracket using the Allen wrench. 2. Slide the projector and projector bracket left or right to move the image. (or move the whiteboard left or right to follow the image). 3. Tighten the two 5/16 screws. 28 Installation and Operation Guide

Image tilt To adjust the tilt angle of the splash screen: 1. Adjust the jack screws on top of the projector mount. Tighten or loosen one jack screw at a time for best results. Image squareness (up and down) To adjust the splash screen squareness: 1. Adjust the thumbwheels on top of the projector bracket at the same time in the same direction. Turn both thumbwheels counterclockwise to make the bottom of the image narrower and the top of the image wider. Turn both thumbwheels clockwise to make the bottom of the image wider and the top of the image narrower. PolyVision 29

2. If one side of the image is taller than the other, loosen all three 4mm thumb screws on the projector bracket, turn the pivot handle counterclockwise to make the left side taller, turn the handle clockwise to make the left side shorter. Tighten all 4mm thumb screws. Image location (up and down) To adjust the splash screen location up and down: 1. Turn the large thumbwheel counterclockwise to move the image up. 2. Turn the large thumbwheel counterclockwise to move the image down. Final check Once all adjustments have been made to the splash screen location, go back through the assembly and ensure that all hardware has been fully tightened. 30 Installation and Operation Guide

Install the PolyVision Driver Projector Add-in To get started using the PolyVision ēno one fixed wall mount for the ultra-short throw projector solution: 1. Ensure that the PolyVision Driver 2.1 (or newer) has been installed on the teacher s computer prior to completing the next step. 2. Connect the USB and VGA cables to the teacher s computer. Proceed with instructions provided with the ēno interactive whiteboard to prepare the ēno stylus for use. PolyVision 31

Appendix 1: Backer board installation WALL MOUNTING INSTRUCTIONS ENO ONE 2610/2810 HEIGHT ADJUSTABLE MOUNT INSTALLATION ON DRYWALL OVER STUDS @ 24" CENTERS WARNING IT IS THE INSTALLER'S RESPONSIBILITY TO CONFIRM THAT THE SUPPORTING WALL SURFACE WILL SAFELY SUPPORT THE 200 LB MAXIMUM COMBINED LOAD OF THE EQUIPMENT AND ALL ATTACHED COMPONENTS AND HARDWARE IN COMPLIANCE WITH APPLICABLE BUILDING CODES. THIS PRODUCT IS ONLY TO BE INSTALLED BY WORKERS SKILLED IN BASIC BUILDING CONSTRUCTION WHO HAVE READ AND FULLY UNDERSTAND THE FOLLOWING WALL MOUNTING INSTRUCTIONS. THIS EQUIPMENT MAY BE MOUNTED ON 1/2" MINIMUM THICKNESS DRYWALL OVER WOOD OR METAL STUDS.IF DRYWALL IS MORE THAN 5/8" THICK, FASTENER LENGTHS WILL NEED TO BE INCREASED ACCORDINGLY FROMTHOSE SPECIFIED BELOW. MAKE SURE SCREWS ARE INSTALLED INTO THE CENTER OF STUDS. USE OF AN "EDGE FINDER" TYPE OF STUD FINDER IS HIGHLY RECOMMENDED. IF STUDS ARE WOOD, INSTALL TAPPING SCREWS DIRECTLY INTO STUDS. IF STUDS ARE METAL, THE MINIMUM METAL THICKNESS IS 24 GAUGE, AND TOGGLE ANCHORS MUST BE USED WITH MACHINE SCREWS. DO NOT INSTALL TAPPING SCREWS DIRECTLY INTO METAL STUDS! ALWAYS USE AN ASSISTANT TO AID IN SAFELY LIFTING AND POSITIONING THE EQUIPMENT BEING INSTALLED. TIGHTEN FASTENERS FIRMLY, BUT DO NOT OVER-TIGHTEN. OVERTIGHTENING CAN CAUSE DAMAGE AND GREATLY REDUCE HOLDING POWER. CONSULT FASTENER MANUFACTURER FOR TORQUE RANGE. THIS PRODUCT IS INTENDED FOR INDOOR INSTALLATION ONLY. OUTDOOR INSTALLATION COULD LEAD TO PRODUCT FAILURE AND PERSONAL INJURY. TOOLS REQUIRED: 1) STUD FINDER - EDGE FINDER TYPE 2) TAPE MEASURE 3) 24 INCH LEVEL 4) 12" X 24" CARPENTER'S SQUARE 5) 3/8" DRILL MOTOR6) #2 PHILLIPS HEX DRIVER BIT OPTIONAL (FOR USE WITH DRILL MOTOR) 7) HAMMER 8) SCREWDRIVER - #2 PHILLIPS 9) 9/16" HEX SOCKET, 2.00" EXTENSION & 1/2" RATCHET 10) 9/64" (0.141) DRILL BIT (PILOT HOLE FOR METAL STUDS) 11) 7/32 (0.219) DRILL BIT 12) 29/64 (0.453) DRILL BIT 13)1/2" (0.500) STEP DRILL BIT (FOR USE WITH TOGGLE ANCHORS INDRYWALL AND METAL STUDS) 32 Installation and Operation Guide

PARTS/MATERIALS REQUIRED: 1) 3/4" THICK PLYWOOD PANEL PRE CUT TO 18" X 66". USE CABINET GRADE PLYWOOD OF GOOD QUALITY TO INSURE A MECHANICALLY SOUND MOUNTING MEDIUM. 2) (6) 3/8-16 TEE NUT, W/SELF LOCKING THREADS, 7/16" BARREL X 7/16" HIGH BARREL HEIGHT. McMASTER-CARR P/N 93766A500 3) (6) 3/8-16 X 1 1/4" LONG, CAP SCREW, GRADE 5, SERRATER FLANGE HEX, STEEL, ZINC PLATE McMASTER-CARR P/N 92323A5564) 4) (10) #10 X 2 1/2" LONG TAPPING SCREW, TRUSS HEAD PHILLIPS, STEEL, ZINC PLATE McMASTER-CARR P/N 93406A254 5) (4) TOGGLE ANCHOR, 10-24 THREADS McMASTER-CARR P/N 97802A314 6) (4) 10-24 X 2.00 LONG, PAN HEAD PHILLIPS, STEEL, ZINC PLATE McMASTER-CARR P/N 90272A2537) 7) (4) #10 FLAT WASHER, 7/32" ID X 1/2" OD, STEEL, ZINC PLATE McMASTER-CARR P/N 90126A514 (24" CENTERS) PolyVision 33

1. DETERMINE WALL LOCATION WHERE THE SPRING ADJUSTMENT MECHANISM WILL MOUNT. 2. INSURE THAT WALL IS SECURE AND SOUND WITH NO STRUCTURAL DEFECTS. 3. LOCATE ANE MARK CENTER LOCATION OF STUDS ON 24 INCH CENTERS. THESE CENTERS WILL LATER BE TRANSFERRED TO THE PLYWOOD ADAPTER PANEL THAT THE SPRING ADJUST MECHANISM WILL BE MOUNTED ON. 34 Installation and Operation Guide

1. ON THE BACK OF THE PLYWOOD ADAPTER PANEL, THE SIDE THAT WILL FACE THE DRYWALL, CAREFULLY LAYOUT AND DRILL (4) THROUGH 29/64" HOLES, HOLES AS SHOWN ABOVE. 2. AFTER DRILLING THE THROUGH INSERT THE 29/64" THROUGH HOLES, INSERT THE (4) 3/8-16 TEE NUTS AND HAMMER THE FLANGE FLUSH WITH THE SURFACE OF THE PLYWOOD PANEL. PolyVision 35

1. PLACE PLYWOOD ADAPTER PANEL AGAINST WALL AS SHOWN ABOVE. BE SURE THAT THE TEE NUT FLANGE SIDE IS AGAINST THE WALL. 2. ADJUST PANEL LOCATION TO AGREE WITH DIMENSIONS AS SHOWN ABOVE AND INSURE THAT THE PANEL IS LEVEL. 3. TRANSFER STUD CENTERLINES (THAT WERE PREVIOUSLY MARKED ON WALL) TO THE PLYWOOD ADAPTER PANEL. 4. REMOVE PLYWOOD ADAPTER PANEL FROM THE WALL. 5. CAREFULLY LAYOUT HOLE PATTERN "S" AS SHOWN ABOVE AND DRILL 7/32" HOLES THROUGH THE PANEL. 6. WITH A PENCIL OR OTHER MARKER, MARK THESE HOLES WITH THE LETTER "S" TO INDICATE WHERE SCREWS WILL BE PLACED INTO WOOD STUDS. 7. CAREFULLY LAYOUT HOLE PATTERN "H" AS SHOWN ABOVE AND DRILL 7/32" HOLES THROUGH THE PLYWOOD ADAPTER PANEL 8. WITH A PENCIL OR OTHER MARKER, MARK THESE HOLES WITH THE LETTER "H" TO INDICATE WHERE SCREW WILL BE PLACED INTO TOGGLEANCHORS THAT WILL BE INSTALLED INTO DRYWALL LATER. 36 Installation and Operation Guide

9. PLACE PLYWOOD ADAPTER PANEL AGAINST WALL AS SHOWN ABOVE. BE SURE THAT THE TEE NUT FLANGE SIDE IS AGAINST THE WALL. 10. ADJUST PANEL LOCATION TO AGREE WITH DIMENSIONS AS SHOWN ABOVE AND INSURE THAT THE PANEL IS LEVEL. 11. TRANSFER THE HOLE CENTERS MARKED "H" THROUGH THE PLYWOOD ADAPTER PANEL TO THE DRYWALL. 12. REMOVE PLYWOOD ADAPTER PANEL FROM THE WALL. 13. DRILL 1/2" HOLES THROUGH THE DRYWALL AT THE "H" CENTERS TRANSFERRED FROM THE PLYWOOD ADAPTER PANEL. 14. INSTALL TOGGLE ANCHORS BY PUSHING THE TOGGLE THROUGH THE 1/2" HOLE, THEN PULL THE ANCHOR BACK TOWARDS YOU UNTIL TOGGLE RESTS FIRMLY AGAINST THE BACK SURFACE OF THE DRYWALL. NEXT, SLIDE THE RETAINER CAP UP TO THE WALL FIRMLY AND SNAP OFF THE STRAPS. 15. PLACE PLYWOOD ADAPTER PANEL ON WALL (TEE NUT FLANGE SIDE AGINST WALL), ALIGNING THE "H" HOLES WITH THE TOGGLE ANCHORS PREVIOUSLY INSTALLED ABOVE. INSTALL 10-24 X 2" LONG PAN HD PHILLIPS MACHINE SCREWS AND #10 FLAT WASHERS (4 PLACES) AND TIGHTEN SECURELY. 16. INSTALL #10 X 2 1/2" TRUSSHEAD TAPPING SCREWSIN HOLES MARKED "S" AND TIGHTEN SECURELY (10 PLACES). DO NOT OVER TIGHTEN! 17. MOUNT ENO ONE WALL BRACKETS WITH 3/8-16 X 1 1/4" LONG CAP SCREW, GRADE 5, HEX FLANGE STEEL BOLTS. 18. INSTALL ENO ONE ADJUSTABLE WALL MOUNT PER INSTALLATION MANUAL. PolyVision 37

Index Backer board installation, 17, 32 Bottom tray, 7 Brake handle, 9 Cable routing, 20, 22 Connect cables, 19 Corrugated cable manager, 6, 22 Final check, 30 Focus, 27 Gas spring installation, 10 Hardware kit, 6 Icon strip, 26 Image location (left to right), 28 Image location (up and down), 30 Image size, 27 Image tilt, 29 Interactive whiteboard mounting brackets, 7, 24 Laptop tray, 7, 15 Lift system, 6 Lift system wall brackets, 6 Mobile stand assembly, 13 Mobile stand legs, 7 Mounting the interactive whiteboard, 25 PolyVision Driver 2.1, 31 Projector adjustment, 27 Projector icon strip, 5 Remote, 5 Required tools, 8 Troubleshooting, 27 Ultra-short, 5 ultra-short throw projector, 3 USB cable, 5 Wall mounting bracket locations, 16 38 Installation and Operation Guide