PIDN-T025B Downlight 25W LED Driver 12V - 36V / 0.7A / 25.2W Features Dimming Method: 0-10V Dimming(0V=1%) Wide dimming range from 1% to 100% Isolation Dimmer Control Constant Current Control Fixed Output Current Active Power Factor Correction Protection : OVP, SCP Specification Summary Mechanical Outline (Plastic Case) - 96 78 30mm EN 61347-1, EN 61347-2-13, K61347-1, K61347-2-13, K62384 Safety Certifications Approved RoHS Compliant Output [W] Output [Vdc] Output [A] Input [Vac] Dim. Method PF Efficiency [%] Mechanical Outline [LxWxH mm] 25.2 12-36 0.7 120-277 0-10V Min. 0.9 Min. 81 96 X 78 X 30 Input Specifications Parameter Min. Typ. Max. Unit Remark Input Voltage (Nominal) 120 230 277 Vac Performance range Input Voltage (Performance) 108-305 Vac AC Variable range Input Current - - 0.4 A Full load @ 120V~277V Input Wattage - 35 - W Full load @ 120V~277V Nominal Input Frequency 47 50/60 63 Hz - Efficiency 81 - - % Power Factor 0.9 - - - THD - - 20 % Full load @ 120V~277V Please refer to Performance Curve Inrush Current - - 50 Amax Full load 220V~240V Note : All parameters NOT specially mentioned are measured at rated load and 25 of ambient temperature. 1 / 11
Output Specifications Parameter Min. Typ. Max. Unit Remarks Output Voltage 12 24 36 V Caution : All User Condition should meet into this Vf range Output Current - 0.7 - A Fixed Current Output Dimming Current Range 1 100 % 0-10V Dimming Output Current Tolerance -5-5 % @ 100% Dimming Output Ripple Current - - 20 % = Peak to Peak / avg @ 100% Dimming Output Power - - 25.2 W Full load @ 120V~277V Start-up Time - - 1,000 ms Full load @ 120V~277V Protections Functions Parameter Min. Typ. Max. Unit Remark Output Over Voltage Protection - - 60 V Auto-recovery Or Latch Output Short Circuit Protection - - - A Auto-recovery Or Latch Hot wiring test - - - - No damage LLP and LED PKG Environmental Specifications Parameter Min. Typ. Max. Unit Remark Temperature Operation -30-55 @ Ta - - 85 @ Tc Storage -35-85 @ Ta Humidity Operation 10-90 % - Storage - - 95 % - Lifetime 50 - - KHrs Note : All parameters NOT specially mentioned are measured at rated load and 25 of ambient temperature. 2 / 11
Standards Parameter Condition Remark Safety Standards EMI / RFI Standards Design to meet the requirements as follows ; UL/cUL : Class 2 Power (UL 8750, CAN/CSA C22.2 No. 250.13-12) IP66 Design to meet the requirements as follows ; EMC FCC : Part 15, Class B Class 2 Wiring method = UL Class 2 + CSA LVLE (LOW-VOLTAGE, LIMITED-ENERGY) Any changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment. 3 / 11
THD[%] PF Efficiency[%] Downlight Performance Curves 100 Efficiency vs Output Power 80 60 40 20 120Vac/60Hz 277Vac/50Hz 0 0 5 10 15 20 25 30 Pout[W] Power Factor vs Output power 1.2 1 0.8 0.6 0.4 0.2 0 0 5 10 15 20 25 30 Pout[W] 120Vac/60Hz 277Vac/50Hz 30 25 20 15 10 5 0 THD vs Output Power 0 5 10 15 20 25 30 Pout[W] 120Vac/60Hz 277Vac/50Hz 4 / 11
Iout[A] Downlight Dimming Control - 0-10V Dimming (0V=10%) 0.8 Dimming Curve 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 1 2 3 4 5 6 7 8 9 Dimming V Open Dim+/- Driver-max(0.7A, Typ) Current 0-10V 0-10V Dimming Curve Short Driver-min(10mA under,typ, 1% Dim) 2) The status of Dim Block with Dimmer. Parameters Position Min. Typ. Max. Source Current out of 0-10V DIM (Gray Wire) 0 ma - 500 ua Absolute Voltage Range on 0-10V (+) DIM + (Purple Wire) -2.0 V - +15 V Reference Dimmer : IP710-DLZ 5 / 11
LG Innotek LG Innotek Inc. Downlight Mechanical Outline 1. Case Dimension (Unit: mm) 6 / 11
Mechanical Outline 2. Connector Description 2.1 AC Cable Item No Name Color Wire Type AC Input 1 L (Live) Black UL1015#18AWG 2 N (Neutral) White UL1015#18AWG 2.2 DC Cable Item No Name Color Wire Type DC output Dimmer 1 VLED+ Red UL1569#18AWG 2 VLED- Blue UL1569#18AWG 1 DIM+ Purple UL1569#22AWG 2 DIM- Gray UL1569#22AWG 2.3 Connection Map AC Input LED Power Driver VLED+(Red) VLED-(Blue) Dim+(Purple) Dim-(Gray) 0-10 Dimmer NEUTRAL(White) LIVE(Black) LED Load VLED+ VLED- 7 / 11
Caution Parameter Condition Remark AC ON AC ON/OFF Digital IC need build up time. - After AC ON- 20s later, LED driver will be stabilization. Digital IC need Reset time. - On Condition of AC ON ON 600ms OFF, It needs 600ms power on time for IC reset. - AC Dip Test is no problem. (Be careful AC chattering condition). Ex) PF/THD/Efficienc y..etc AC Variation Digital IC have quick internal response of PFC Block. - When AC input voltage change from Low AC to High AC, LED stop and operation. We recommend to use after fixing AC voltage. Load LED(O), CV mode(o), CR mode(x) If you want to CR mode, please add below method. 1. VLED+ add diode Vf 1V. 2. Add circuit of CR load. ( Note 1) CV : constant Voltage mode CR : constant Resistor mode Note 1 : Additional CR mode circuit Resistor load 25W : 51Ω 8 / 11
Caution Storage 1) Suitable for indoor use or outdoor use without direct sunlight exposure 2) This product should not be exposed to sulfur. Transportation 1) Be careful to give mechanical vibration and shock as less as possible and not to drop this product. 2) Static electricity or surge voltage may damage the components inside this product, as such please observe proper anti-electrostatic working process. - People handing the Driver should be well grounded and wear anti-static working clothes and gloves. - All related devices and instruments in the production line should be well grounded. Installation 1) Be careful not to warp or bend this product at assembly. 2) Be careful not to apply stress to the parts such as connectors at assembly. 3) Please note these guidelines and precautions. It is required to be assembled by experienced workers. - Check the power cord is disconnected from the power outlet when this power supply is being installed. - Do not use a damaged input and output lines. If it is damaged, change the power supply through the supplier. - Check the input and output lines are connected correctly. 4) Observe the correct polarity of output terminal. 5) Do not modify this product. It causes a fire and the electric shock. 6) Turn off the power before exchanging LED lamps. 7) The Protective Earth(PE) must be securely connected to Frame Ground(FG) in case the driver is certified with class I (i.e. inclusive of a PE contact) Use Conditions 1) This product must be used within the specification. Any defects or damages resulting from abnormal conditions will not be covered by warranty - In case of the product with latch off function can be shut down under abnormal situations. Under this situation please restart the power supply, after resolving abnormality. 2) This product is for general electronics equipment such as Audio-Visual equipment, household electronics, office supplies, information services and telecommunications; therefore, in case this product is used for medical equipment, space equipment, nuclear equipment or disaster prevention equipment, please contact LG INNOTEK in advance. 3) This product is designed and intended to operate LED loads only. Non-LED loading may be outside the specified design limits of our LED driver, and therefore cannot be covered by the warranty. If you desire to use our product to operate non-led loads please contact us to discuss compatibility. 4) This product is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must re-qualify EMC Directive on the complete installation again. 9 / 11
Caution FCC Verification This device complies with Part 15 of the FCC Rules. Operation is subject to the following t wo conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. For Class B digital device INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:.-. Reorient of relocate the receiving antenna. -. Increase the separation between the equipment and receiver. -. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -. Consult the dealer or an experienced radio/tv technician for help. WARNING Any changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment. Note: The manufacturer is not responsible for any Radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user s authority to operate the equipment. 10 / 11
Datasheet Revision History Change Date Rev. No. 2015/11/09 1.0 Initial Release Description of Change Remark 11 / 11