IP65 IP67 SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT DC VOLTAGE CONSTANT CURRENT REGION Note.4 6 ~1V RATED CURRENT RATED POWER VOLTAGE ADJ. RANGE Note.6 10.8 ~ 13.5V CURRENT ADJ. RANGE LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FTOR EFFICIENCY (Typ.) CURRENT INRUSH CURRENT( Typ.) LEAKAGE CURRENT WORKING TEMP. WORKING HUMIDITY SAFETY STANDARDS Note.8 Note.5 STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION Note.7 UL8750, EN61347-1, EN61347--13 independent IP65 or IP67 approved ; Design refer to UL60950-1, TUV EN60950-1 WITHSTAND VOLTAGE -:3.75KV -FG:1.88KV -FG:0.5KV SAFETY & ISOLATION RESISTANCE -, -FG, -FG:100M Ohms / 500VDC / 5 / RH EMC EMI CONDUCTION & RADIATION Compliance to EN55015, EN550 (CISPR) Class B HARMONIC CURRENT Compliance to EN61000-3- Class C ( load) ; EN61000-3-3 OTHERS NOTE RIPPLE & NOISE (max.) Note. 150mVp-p VOLTAGE TOLERANCE Note.3 OVER CURRENT SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE EMS IMMUNITY MTBF 1V 15V ~ 54V -1-15 -0-4 -30-36 -4-48 1V Can be adjusted by internal potential meter or through output cable 6.5 ~ 13A.5% 500ms, 80ms at full load 30V / 115V ; B type 500ms, 00ms at 95% load 30V / 115V 16ms at full load 30V / 115V 90 ~ 305V 17 ~ 431VDC 47 ~ 63Hz 15V.0% PF 0.95/30V PF 0.98/115V at full load and rated output voltage PF 0.9 at 50 ~ load 91.5% 9% 93% 93.5% 93.5% 93.5% 94% 94% 94% 1.8A / 115V 0.8A / 30V 0.7A / 77V.1A / 115V 0.9A / 30V 0.8A / 77V COLD START 75A/30V <0.75mA / 77V 7.5 ~ 15V 5.75 ~ 11.5A 95 ~ 108% Note.4 Protection type : Constant current limiting, recovers automatically after fault condition is removed Constant current limiting, recovers automatically after fault condition is removed 14 ~ 17V 18 ~ 1V 3 ~ 7V 8 ~ 34V 34 ~ 38V 41 ~ 46V 47 ~ 53V 54 ~ 60V 59 ~ 65V 100 10 (RTH) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -40 ~ +60 @ full load ; +70 @ load (Refer to derating curve) 0 ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH 0.03%/ (0 ~ 50 ) 0V 10 ~ 0V 4.65 ~ 9.3A 10 ~ 500Hz, 5G 1min./1cycle, period for 7min. each along X, Y, Z axes Compliance to EN61000-4-,3,4,5,6,8,11; ENV5004, EN61547, EN5504, heavy industry level (surge 4KV), criteria A 19.Khrs min. MIL-HDBK-17F (5 ) 4V 1 ~ 4V 3.9 ~ 7.8A 3.1 ~ 6.A DIMENSION 8*68*38.8mm (L*W*H) PKING 1.15Kg; 1pcs/14.8Kg/0.76CUFT.6 ~ 5.A. ~ 4.4A 1.95 ~ 3.9A 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5%.0% 1.5% 0.5% 0.5% 0.5% 0.5% 0.5% 30V 15 ~ 30V 36V 18 ~ 36V 13A 11.5A 9.3A 7.8A 6.A 5.A 4.4A 3.9A 48V 4 ~ 48V 156W 17W 186W 187.W 186W 187.W 184.8W 187.W 150mVp-p 13.5 ~ 17V 150mVp-p 17 ~ V 150mVp-p ~ 7V 00mVp-p 7 ~ 33V 00mVp-p 33 ~ 40V Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery 4V 1 ~ 4V 00mVp-p 38 ~ 46V 00mVp-p 43 ~ 53V -54 54V 7 ~ 54V 3.45A 186.3W 00mVp-p 49 ~ 58V 1.7 ~ 3.45A 0.5% 0.5%
Mechanical Specification Case No.994D Unit:mm Blank:() 8 1 04 9.6 FG (Green/Yellow) /L(Brown) /N(Blue) A Type:(-_A) FG (Green/Yellow) /L(Brown) /N(Blue) 300 0 SJTW 18AWG(0.75mm ) 3C IP67 rated. Cable for I/O connection. 300 0 SJTW 18AWG(0.75mm ) 3C 1 9.6 9.4 9.4 34. 9.4 9.4 34. 68 68 8 04 Vo Io ADJ. ADJ. 300 0 SJTW 14AWG(1.5mm ) C 4. 4PL 300 0 SJTW 14AWG(1.5mm ) C 4. 4PL -V(Black) +V(Red) 38.8 -V(Black) +V(Red) 38.8 IP65 rated. Output voltage and constant current level can be adjusted through internal potential meter. (Can access by removing the rubber stopper on the case.) File Name:-SPEC 010-1-4
B Type:(-_B) 8 1 04 FG (Green/Yellow) /L(Brown) /N(Blue) 300 0 SJTW 18AWG(0.75mm ) 3C 9.6 9.4 34. 9.4 68 4. 4PL 300 0 SJTW 18AWG(0.75mm ) C SJTW 14AWG(1.5mm ) C DIM+(Blue) DIM-(White) -V(Black) +V(Red) 38.8 IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistor or 1 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-. Please DO NOT connect "DIM-" to "-V". Reference resistance value for output current adjustment (Typical) Resistance value Percentage of rated current 10K 0K 0% 30K 40K 50K 60K 70K 80K 90K 100K OPEN ~108% 1 ~ 10V dimming function for output current adjustment (Typical) Dimming value Percentage of rated current 1V V 3V 4V 5V 6V 7V 8V 9V 10V 0% OPEN ~108% 10V PWM signal for output current adjustment (Typical): Frequency range :100HZ ~ 3KHz Duty value 0% OPEN Percentage of rated current 0% ~108% Block Diagram Fosc : 100KHz FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. O.T.P. POWER SWITCHING PWM CONTROL RECTIFIERS & FILTER O.V.P. O.L.P. DETECTION CIRCUIT +V -V DIM+ DIM- (B Type) Derating Curve 100 80 60 Static Characteristics 100 90 80 70 fosc : 100KHz LOAD (%) 40 0 LOAD (%) 60 50 40-40 -5-10 0 15 30 50 60 70 AMBIENT TEMPERATURE ( ) (HORIZONTAL) 90 100 15 135 145 155 165 175 180 00 30 305 INPUT VOLTAGE (V) 60Hz File Name:-SPEC 010-1-4
Power Factor Characteristic Power factor will be higher than 0.9 when output loading is or higher. Constant Current Mode PF 1.0 1 0.9 8 0.9 6 0.9 4 0.9 0.9 0.8 8 0.8 6 0.8 4 5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 1 0 0 % 3 0 V A C 1 1 0 V A C LOAD EFFICIENCY vs LOAD (48V Model) possess superior working efficiency that up to 94% can be reached in field applications. EFFICIENCY (%) 97 95 93 91 89 87 85 83 81 79 77 75 73 71 69 67 65 0% 30V 110V LOAD DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B). 100 Vo(%) 50 (A) Constant Voltage area (B) Constant Current area 50 100 Io (%) Typical LED power supply I-V curve File Name:-SPEC 010-1-4
Direct driving : Under direct driving, the power supply will work in "constant current mode (CC)" and output voltage of the power supply will be clamped by sum of forward voltage (V F) of the LED strip. The total forward voltage of series connecting LEDs is suggested for ~95% of power supply rated output voltage due to concern of the best PF value and efficiency. ~ With LED driver Using additional driver, the power supply will work in "constant voltage mode (CV)" and output voltage of the power supply will be kept in rated value. In this drive mode, several design issues need to be considered: 1.Output voltage of PSU must be higher than total forward voltage of series connecting LEDs by 3V minimum..input capacitor (Cin) of LED driver circuit should use 47uF ~ 100uF(typ.) of rating depends on the operating frequency of the LED driver. The higher the operating frequency is used, the smaller value of Cin should be chosen, and vice versa. 3.Do not use B type with LED driver. R Cin Cout VF L ~ IC Circuit DIMMING OPERATION(for B-type only) Using the built-in dimming function on B-type model can't turn the lighting fixture totally dark. Please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the LED power supply unit. Dimming connection diagram for turning the lighting fixture ON/OFF : N FG L Relay Switch Adjuster 0~100K Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue /L /N B Type DIM+ DIM- V(-) V(+) Blue White Black Red LED Lighting Using a switch and relay can turn ON/OFF the lighting fixture. 1.Output constant current level can be adjusted through output cable by connecting a resistor or 1~10Vdc or 10V PWM signal between DIM+ and DIM-..The LED lighting fixture can be turned ON/OFF by the switch. File Name:-SPEC 010-1-4
EMI DEBUG SUGGESTION C LED CC driver Chassis of LED Lamp CC IC ~ FG B A D A A. Add a common mode ferrite choke on output wires to reduce the common emission between 10M ~ 300MHz per lighting EMI regulation. B. Chassis of LED lamp and chassis of or the FG wire should be connected to the safety ground to reduce the EMI noise, including the conduction and radiation emission. C. The additional X-Cap and discharge resistor can reduce the low frequency conduction noise between 9K ~ 1MHz per lighting EMI regulation. D. L-C filter should be added at the DC input of LED constant current driver to avoid the differential emission and high frequency noise generated by the CC driver. WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of to operate in dry/wet/damp or outdoor environment. Size Pin Configuration (Female) Size Pin Configuration (Female) M1 Order No. Suitable Current 4-PIN 5A/PIN M1-04 10A max. 5-PIN 5A/PIN M1-05 10A max. M15 Order No. Suitable Current -PIN 1A/PIN M15-0 1A max. LED Lamp Cable Joiner 66 6 0 Suitable for 14AWG~AWG 5 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp Wires File Name:-SPEC 010-1-4