series IP65 IP67 SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE CONSTANT CURRENT REGION Note.4 6 ~1V RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note. 150mVp-p VOLTAGE ADJ. RANGE Note.6 10.8 ~ 13.5V CURRENT ADJ. RANGE VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FTOR EFFICIENCY (Typ.) CURRENT INRUSH CURRENT( Typ.) LEAKAGE CURRENT OVER CURRENT SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMS IMMUNITY MTBF Note.8 500ms, 80ms at full load Note.5 STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION 1V 15V ~ 54V -1-15 -0-4 -30-36 -4-48 -54 1V Can be adjusted by internal potential meter or through output cable 6.5 ~ 13A.5% 16ms at full load 30V / 115V 90 ~ 64V 17 ~ 370VDC 47 ~ 63Hz 15V 30V / 115V PF 0.95/30V PF 0.98/115V at full load and rated output voltage PF 0.9 at 50 ~ 100% load 1.8A / 115V 0.8A / 30V.1A / 115V 0.9A / 30V COLD START 75A/30V <0.75mA / 40V 7.5 ~ 15V 5.75 ~ 11.5A.0% 9% 93% 93.5% 94% 94% 94% 94% 94% 94% 95 ~ 108% Note.4 Protection type : Constant current limiting, recovers automatically after fault condition is removed Constant current limiting, recovers automatically after fault condition is removed 14 ~ 17V 18 ~ 1V 3 ~ 7V 8 ~ 34V 34 ~ 38V 41 ~ 46V 47 ~ 53V 54 ~ 60V 59 ~ 65V Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery 100 10 (RTH) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -30 ~ +60 @ full load ; +70 @ load (Refer to derating curve) ; -40 can power on 0 ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH 0.03%/ (0 ~ 50 ) 4.65 ~ 9.3A 10 ~ 500Hz, 5G 1min./1cycle, period for 7min. each along X, Y, Z axes Note.7 EN61347-1, EN61347--13 independent approved ; Design refer to UL8750, UL60950-1, TUV EN60950-1 -:3.75KV -FG:1.88KV -FG:0.5KV -, -FG, -FG:100M Ohms / 500VDC / 5 / RH EMI CONDUCTION & RADIATION Compliance to EN55015, EN550 (CISPR) Class B HARMONIC CURRENT Compliance to EN61000-3- Class C ( load) ; EN61000-3-3 0V 10 ~ 0V Compliance to EN61000-4-,3,4,5,6,8,11; ENV5004, EN61547, EN5504, light industry level (surge 4KV), criteria A 19.Khrs min. MIL-HDBK-17F (5 ) 4V 1 ~ 4V 3.9 ~ 7.8A 3.1 ~ 6.A DIMENSION 8*68*38.8mm (L*W*H) PKING 1.15Kg; 1pcs/14.8Kg/0.76CUFT.6 ~ 5.A. ~ 4.4A 1.95 ~ 3.9A 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5%.0% 1.5% 0.5% 0.5% 0.5% 0.5% 0.5% 30V 15 ~ 30V 36V 18 ~ 36V 13A 11.5A 9.3A 7.8A 6.A 5.A 4.4A 3.9A 48V 4 ~ 48V 156W 17W 186W 187.W 186W 187.W 184.8W 187.W 150mVp-p 13.5 ~ 17V 150mVp-p 17 ~ V 150mVp-p ~ 7V 00mVp-p 7 ~ 33V 00mVp-p 33 ~ 40V 4V 1 ~ 4V 00mVp-p 38 ~ 46V 00mVp-p 43 ~ 53V 54V 7 ~ 54V 3.45A 186.3W 00mVp-p 49 ~ 58V 1.7 ~ 3.45A 0.5% 0.5%
series Mechanical Specification Case No.994D Unit:mm Blank:() 1 9.6 8 04 9.4 /L(Brown) /N(Blue) FG (Green/Yellow) 18AWG(0.75mm ) 3C 14AWG(1.5mm ) C 9.4 34. 38.8 68 4. 4PL +V(Red) -V(Black) IP67 rated. Cable for I/O connection. A Type:(-_A) 1 9.6 8 04 9.4 /L(Brown) Vo Io /N(Blue) ADJ. ADJ. FG (Green/Yellow) 18AWG(0.75mm ) 3C 14AWG(1.5mm ) C 38.8 9.4 34. 68 4. 4PL +V(Red) -V(Black) IP65 rated. Output voltage and constant current level can be adjusted through internal potential meter. (Can access by removing the rubber stopper on the case.) File Name:-SPEC 010-06-1
series B Type:(-_B) 8 1 04 /L(Brown) /N(Blue) FG (Green/Yellow) 18AWG(0.75mm ) 3C 9.6 9.4 34. 9.4 68 4. 4PL 18AWG(0.75mm ) C 14AWG(1.5mm ) C ADJ1(Blue) ADJ(White) +V(Red) -V(Black) 38.8 IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistor or 1 ~ 10Vdc or 10V PWM signal between ADJ1 and ADJ. Reference resistance value for output current adjustment (Typical) Resistance value 10K 0K 30K 40K 50K 60K 70K 80K 90K 100K OPEN Percentage of rated current 0% 100% 104%~106% 1 ~ 10V dimming function for output current adjustment (Typical) Dimming value Percentage of rated current 1V V 3V 4V 5V 6V 7V 8V 9V 10V 0% 100% OPEN 104%~106% 10V PWM signal for output current adjustment (Typical) Duty value 0% 100% OPEN Percentage of rated current 0% 100% 104%~106% Block Diagram Fosc : 100KHz FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT O.V.P. +V -V ADJ1 ADJ (B Type) Derating Curve 100 80 60 Static Characteristics 100 90 80 70 fosc : 100KHz LOAD (%) 40 0 LOAD (%) 60 50 40-30 -5-10 0 15 30 50 60 70 AMBIENT TEMPERATURE ( ) (HORIZONTAL) 90 100 15 135 145 155 165 175 180 00 30 64 INPUT VOLTAGE (V) 60Hz File Name:-SPEC 010-06-1
series Power Factor Characteristic Power factor will be higher than 0.9 when output loading is or higher. Constant Current Mode PF 1.0 1 0.98 0.96 0.94 0.9 0.9 0.88 0.86 0.84 100% 30V 110V LOAD EFFICIENCY vs LOAD (48V Model) series possess superior working efficiency that up to 94% can be reached in field applications. EFFICIENCY (%) 97 95 93 91 89 87 85 83 81 79 77 75 73 71 69 67 65 0% 100% 30V 110V LOAD DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B). 100 Vo(%) 50 (max.) (A) Constant Voltage area (B) Constant Current area 50 100 Io (%) Typical LED power supply I-V curve File Name:-SPEC 010-06-1
series Direct driving : Under direct driving, the power supply will work in "constant current mode (CC)" and output voltage of the power supply will be clamped by sum of forward voltage (V F) of the LED strip. The total forward voltage of series connecting LEDs is suggested for ~95% of power supply rated output voltage due to concern of the best PF value and efficiency. ~ With LED driver Using additional driver, the power supply will work in "constant voltage mode (CV)" and output voltage of the power supply will be kept in rated value. In this drive mode, several design issues need to be considered: 1.Output voltage of PSU must be higher than total forward voltage of series connecting LEDs by 3V minimum..input capacitor (Cin) of LED driver circuit should use 47uF ~ 100uF(typ.) of rating depends on the operating frequency of the LED driver. The higher the operating frequency is used, the smaller value of Cin should be chosen, and vice versa. 3.Do not use B type with LED driver. R Cin Cout VF L ~ IC Circuit Dimming application connection diagram (for turning the lighting ON/OFF) : N FG L Relay Switch Adjuster 0~100K Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue /L /N B Type ADJ1 ADJ V(+) V(-) Blue(+) White(-) Red Black LED Lighting Using a switch and relay can turn ON/OFF the lighting. 1.Output constant current level can be adjusted through output cable by connecting a resistor or 1~10Vdc or 10V PWM signal between ADJ1 and ADJ..The LED lighting can be turned ON/OFF by the switch. File Name:-SPEC 010-06-1
series EMI DEBUG SUGGESTION C LED CC driver Chassis of LED Lamp CC IC ~ FG B A D A A. Add a common mode ferrite choke on output wires to reduce the common emission between 10M ~ 300MHz per lighting EMI regulation. B. Chassis of LED lamp and chassis of or the FG wire should be connected to the safety ground to reduce the EMI noise, including the conduction and radiation emission. C. The additional X-Cap and discharge resistor can reduce the low frequency conduction noise between 9K ~ 1MHz per lighting EMI regulation. D. L-C filter should be added at the DC input of LED constant current driver to avoid the differential emission and high frequency noise generated by the CC driver. WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of to operate in dry/wet/damp or outdoor environment. Size Pin Configuration (Female) Size Pin Configuration (Female) M1 Order No. Suitable Current 4-PIN 5A/PIN M1-04 10A max. 5-PIN 5A/PIN M1-05 10A max. M15 Order No. Suitable Current -PIN 1A/PIN M15-0 1A max. LED Lamp Cable Joiner 66 6 0 Suitable for 14AWG~AWG 5 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp Wires File Name:-SPEC 010-06-1