AMMC - 518-2 GHz Amplifier Data Sheet Chip Size: 92 x 92 µm (.2 x.2 mils) Chip Size Tolerance: ± 1µm (±.4 mils) Chip Thickness: 1 ± 1µm (4 ±.4 mils) Pad Dimensions: 8 x 8 µm (.1 x.1 mils or larger) Description Avago Technologies AMMC18-2 GHz MMIC is an efficient two-stage amplifier designed to be used as a cascadable intermediate gain block for EW applications. In communication systems, it can be used as a LO buffer, or as a transmit driver amplifier. It is fabricated using a PHEMT integrated circuit structure that provides exceptional efficiency and flat gain performance. During typical operation with a single 5-V supply, each gain stage is biased for Class-A operation for optimal power output with minimal distortion. The RF input and output have matching circuitry for use in 5-W environments. The backside of the chip is both RF and DC ground. This helps simplify the assembly process and reduces assembly related performance variations and costs. For improved reliability and moisture protection, the die is passivated at the active areas. The MMIC is a cost effective alternative to hybrid (discrete FET) amplifiers that require complex tuning and assembly processes. Applications Driver/Buffer in microwave communication systems Cascadable gain stage for EW systems Phased array radar and transmit amplifiers Features Frequency Range: - 2 GHz High Gain: 14.5 db Typical Output Power: 19.5 dbm Typical Input and Output Return Loss: < -12 db Flat Gain Response: ±. db Typical Single Supply Bias: 5 V @ 17 ma AMMC18 Absolute Maximum Ratings [1] Symbol Parameters/ Conditions Units Min. Max. V D1, V D2 Drain Supply Voltage V 7 V G1 Optional Gate Voltage V +1 V G2 Optional Gate Voltage V +1 I D1 Drain Supply Current ma 7 I D2 Drain Supply Current ma 84 P in RF Input Power dbm 2 T ch Channel Temp. C + T b Operating Backside Temp. C 5 T stg Storage Temp. C + T max Maximum Assembly Temp. ( sec max) C + Note: 1. Operation in excess of any one of these conditions may result in permanent damage to this device. Note: These devices are ESD sensitive. The following precautions are strongly recommended: Ensure that an ESD approved carrier is used when dice are transported from one destination to another. Personal grounding is to be worn at all times when handling these devices. 1
AMMC18 DC Specifications / Physical Properties [1] Symbol Parameters and Test Conditions Unit Min. Typical Max. V D1,V D2 Recommended Drain Supply Voltage V 5 7 I D1 First stage Drain Supply Current (V D1 = 5V, V G1 = Open or Ground) ma 48 I D2 Second stage Drain Supply Current ma 59 (V = 5V, V = Open or Ground) D2 G2 I D1 + I D2 Total Drain Supply Current (V G1 = V G2 = Open or Ground, V D1 = V D2 = 5 V) ma 17 14 θ ch-b Thermal Resistance [2] (Backside temperature (Tb) = 25 C C/W 22 Notes: 1. Backside temperature T b = 25 C unless otherwise noted 2. Channel-to-backside Thermal Resistance (θ ch-b ) = 2 C/W at T channel (T c ) = C as measured using infrared microscopy. Thermal Resistance at backside temperature (T b ) = 25 C calculated from measured data. [, 5] AMMC18 RF Specifications (T b = 25 C, V DD = 5 V, I DD = 17 ma, Z = 5 Ω) Symbol Parameters and Test Conditions Unit Min. Typical Max. S 21 2 Small-signal Gain db 12.5 14.5 D S 21 2 Small-signal Gain Flatness db ±. RL in Input Return Loss db 9 12 RL out Output Return Loss db 9 12 S 12 2 Isolation db 4 45 P -1dB Output Power at 1dB Gain Compression @ 2 GHz dbm 17.5 19.5 P sat Saturated Output Power (db Gain Compression) @ 2 GHz dbm 2.5 OIP Output rd Order Intercept Point @ 2 GHz dbm 2 DS 21 / DT Temperature Coefficient of Gain [4] db/ C -.2 NF Noise Figure @ 2 GHz db 4.4.5 Notes:. 1% on-wafer RF test is done at frequency =, 1 and 2 GHz, except as noted. 4. Temperature Coefficient of Gain based on sample test 5. All tested parameters guaranteed with measurement accuracy ±1.5dB for S12, ±1dB for S11, S21, S22, P1dB and ±.5dB for NF. 2
AMMC18 Typical Performance (T chuck =25 C, V DD =5V, I DD = 17 ma, Z o =5Ω) 18 GAIN (db) 12 9 ISOLATION (db) -1-2 - -4 - INPUT RL (db) -1 - -2-7 4 7 1 1 1 19 22 4 7 1 1 1 19 22 4 7 1 1 1 19 22 Figure 1. Gain Figure 2. Isolation Figure. Input Return Loss 1 24 8 2 OUTPUT RL (db) -1 - -2 NF (db) 4 P1dB (dbm) 1 12 8 2 4-4 7 1 1 1 19 22 4 7 1 1 1 19 22 4 7 1 1 1 19 22 Figure 4. Output Return Loss Figure 5. Noise Figure Figure. output Power at 1 db Gain Compression AMMC18 Typical Performance vs. Supply Voltage (T b =25 C, Z o =5Ω) 18 GAIN (db) 12 9 Vdd=V ISOLATION (db) -1-2 - -4 Vdd=V INPUT RL (db) -1 - -2 Vdd=V - - 4 7 1 1 1 19 22 4 7 1 1 1 19 22 4 7 1 1 1 19 22 Figure 7. Gain and Voltage Figure 8. Isolation and Voltage Figure 9. Input Return Loss and Voltage
AMMC18 Typical Performance vs. Supply Voltage (cont.) (T b =25 C, Z o =5Ω) 25-1 Vdd=V 2 OUTPUT RL (db) - -2 - P1dB (dbm) 1 5 Vdd=V 4 7 1 1 1 19 22 Figure 1. Output Return Loss and Voltage 4 7 1 1 1 19 22 Figure 11. Output Power and Voltage AMMC18 Typical Performance vs. Temperature (V DD =5V, Z o =5Ω) 18-1 -4 C GAIN (db) 12 9-4 C 4 7 1 1 1 19 22 ISOLATION (db) -2 - -4-4 7 1 1 1 19 22-4 7 1 1 1 19 22 Figure 12. Gain and Temperature Figure 1. Isolation and Temperature Figure 14. Input Return Loss and Temperature INPUT RL (db) -1-2 -4 C 8 25-4 C 7 2 OUTPUT RL (db) -1 - NOISE FIGURE (db) 5 4 P1dB (dbm) 1-2 4 7 1 1 1 19 22 2-4 C 1 4 7 1 1 1 19 22 5-4 C 4 7 1 1 1 19 22 Figure. Output Return Loss and Temperature Figure 1. Noise Figure and Temperature Figure 17. Output Power and Temperature 4
AMMC18 Typical Scattering Parameters [1] (T b =25 C, V DD = 5 V, I DD = 17 ma) Freq GHz S11 S21 S12 S22 db Mag Phase db Mag Phase db Mag Phase db Mag Phase 2. -2.4.7-125 2. 74-8. -14 -.4.95-77 2.5-2.9.72-147.4.2-119 -74. 7 -.9.91-97. -.2.9-1 -19..11-12 -9.1-1..84-118.5 -.. 174-7.4.4-12 9.1 - -2..75-18 4. -4.. 2.8 1.9-147 7.7-14 -.8.4-4.5-4.9.57 12 7.7 2.4 178 1.8-11..55-17 5. -7..4 94 12.5 4.2 18-48.8-142 -.9.45 172 5.5-12.7.2 7 14.7 5.41 94-45.7.1-17 -8..7 1. -19.8.1.1 5.9-44.5.1 11-1.1.1 1.5-2..7 85.1 5.9 4-44..1 142-11..27 141 7. -24.7. 87. 5.4 1-44..1 127-12..2 1 7.5-2.4.5 8. 5.1-44..1 1-1.9.2 12 8. -28.2.4 28 14.9 5.59-22 -4.9.1 1 -..17 19 8.5-2..5-2 14.9 5.57-7 -4..1 95-1.7. 98 9. -22.8.7 5 14.9 5.55 1-4..1 8-18.2.12 87 9.5-19.9.1-74 14.8 5.52-4.2.1 77-19.7.1 74 1. -17.7.1-88 14.8 5.49-77 -4.1.1 7-21.4.9 1.5-1.1.1-1 14.7 5.45-9 -42.9.1-22.8.7 4 11. -14.8.18-11 14.7 5.4-11 -42.8.1 57-24.. 2 11.5-1.9.2-12 14.7 5.41-11 -42.5.1 52.1. 1 12. -1.2.22-128 14. 5.8-124 -42.5.1 45.1. -22 12.5-12..2-1 14. 5.7-14 -42..1 4-24.5. -44 1. -12.2.25-14 14. 5.7-145 -42.1.1 4-2..7-1.5-11.9.2-1 14. 5.8-41.9.1 1-22.2.8-7 14. -11..2-9 14.7 5.4-1 -41.7.1 24-21..9-85 14.5-11.5.27-1 14.7 5.42-17 -41..1 19-2.7.9-95. -11.4.27-174 14.7 5.4 174-41.4.1-19.8.1 -.5-11.4.27 177 14.8 5.49 1-41..1 9-19.1.11-11 1. -11.5.27 18 14.9 5.54-41.1.1-18.4.12-121 1.5-11.7.2 7 14.9 5.58 142-4.8.1-17.7.1-12 17. -11.9.25 14. 5. 11-4.8.1-7 -17.2.14-12 17.5-12.2.25 12.1 5. 12-4.8.1-12 -1.7. -18 18. -12.4.24 11.1 5.71 19-4.5.1-1 -1.2.1-14 18.5-12.4.24 98.2 5.75 97-4.4.1-2 -.8.1-148 19. -12.2.25 77.2 5.75 85-4..1-29 -.4.17-4 19.5-11.5.27 5.2 5.7 7-4.1.1-14.9.18-8 2. -1.5. 4. 5.5-9.9.1-42 -14..19-1 2.5-9.2.5 14 14.8 5.51 4-9.9.1-48 -14..2-1 21. -7.9.4 14.5 5.1-4..1 5-1.8.2-172 21.5 -.7.4-21 14.1 5.5 19-9.8.1 - -1.5.21-17 22..7.52-1.5 4.72 5-4..1-72 -1.1.22 179 Note: 1. Data obtained from on-wafer measurements 5
Biasing and Operation The AMMC18 is normally biased with a single positive drain supply connected to both V D1 and V D2 bond pads as shown in Figure 19(a). The recommended supply voltage is to 5 V. No ground wires are required because all ground connections are made with plated through-holes to the backside of the device. Gate bias pads (V G1 & V G2 ) are also provided to allow adjustments in gain, RF output power, and DC power dissipation, if necessary. No connection to the gate pad is needed for single drain-bias operation. However, for custom applications, the DC current flowing through the input and/or output gain stage may be adjusted by applying a voltage to the gate bias pad(s) as shown in Figure 19(b). A negative gate-pad voltage will decrease the drain current. The gate-pad voltage is approximately zero volt during operation with no DC gate supply. Refer to the Absolute Maximum Ratings table for allowed DC and thermal conditions. Assembly Techniques The backside of the AMMC18 chip is RF ground. For microstripline applications, the chip should be attached directly to the ground plane (e.g., circuit carrier or heatsink) using electrically conductive epoxy [1, 2]. For best performance, the topside of the MMIC should be brought up to the same height as the circuit surrounding it. This can be accomplished by mounting a gold plated metal shim (same length and width as the MMIC) under the chip, which is of the correct thickness to make the chip and adjacent circuit coplanar. The amount of epoxy used for chip and or shim attachment should be just enough to provide a thin fillet around the bottom perimeter of the chip or shim. The ground plane should be free of any residue that may jeopardize electrical or mechanical attachment. The location of the RF bond pads is shown in Figure 2. Note that all the RF input and output ports are in a Ground-Signal-Ground configuration. RF connections should be kept as short as reasonable to minimize performance degradation due to undesirable series inductance. A single bond wire is sufficient for signal connections, however double-bonding with.7 mil gold wire or the use of gold mesh is recommended for best performance, especially near the high end of the frequency range. Thermosonic wedge bonding is the preferred method for wire attachment to the bond pads. Gold mesh can be attached using a 2 mil round tracking tool and a tool force of approximately 22 grams with an ultrasonic power of roughly 55dB for a duration of 7 ± 8 ms. A guided wedge at an ultrasonic power level of 4 db can be used for the.7 mil wire. The recommended wire bond stage temperature is ± 2 C. Caution should be taken to not exceed the Absolute Maximum Rating for assembly temperature and time. The chip is 1 µm thick and should be handled with care. This MMIC has exposed air bridges on the top surface and should be handled by the edges or with a custom collet (do not pick up die with vacuum on die center.) This MMIC is also static sensitive and ESD handling precautions should be taken. Notes: 1. Ablebond 84-1 LM1 silver epoxy is recommended. 2. Eutectic attach is not recommended and may jeopardize reliability of the device.
V D1 V D2 Feedback Network Matching RF Input Matching Matching RF Output V G1 V G2 Figure 18. AMMC - 518 Schematic To power supply 1 pf chip capacitor To power supply 1 pf chip capacitor gold plated shim gold plated shim RF Input RF Output RF Input RF Output Bonding island or small chip-capacitor (a) To V G1 power supply (b) To V G2 power supply Figure 19. AMMC - 518 Assembly Diagram 7
92 14 55 57 Vd1 GND Vd2 5 RF RF 5 Vg1 Vg2 79 59 92 Figure 2. AMMC - 518 Bond pad locations (dimensions in microns) Ordering Information: AMMC18-W1 = 1 devices per tray AMMC18-W5 = 5 devices per tray For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright 25-21 Avago Technologies. All rights reserved. Obsoletes 5989-927EN AV2-7EN - September 2, 21