Since the rest position is the optimal average working point, DC offset leads to several undesirable consequences: reduced excursion capabilities,

With over 70 years of industry experience, B&C Speakers has designed and built thousands of unique transducers. Each year, our sales and engineering teams work together to develop a comprehensive catalogue. While this catalogue reflects the large majority of our technologies, it is primarily designed to feature more recent additions to the product range. Please refer to our web site (http://www.bcspeakers.com) to get the latest product updates throughout the year. You will also find more detailed specifications and physical dimensions for all standard models. Our web site is by far our most up-todate and complete product information resource. POWER HALING B&C s specified Nominal Power Handling is measured according to the AES-98 standard. The transducer under test is driven for a two-hour period with a pink noise signal having a crest factor of (or 6 db), and filtered to the working range of the transducer itself. For instance, a 50-500 range is typical for woofer testing. Cone loudspeakers are tested in free air. Compression drivers are coupled to their recommended horn. Power is calculated using the RMS value of applied voltage averaged over the test period and the minimum value of electrical impedance within the working range of the loudspeaker. After the test, the transducer must be in working order, without permanent impact on its technical performance. Due to the transient character of most musical programs, whose crest factor is commonly db or more, it is customary to specify a Continuous Program, double of the Nominal, as a recommended amplifier power in order to fully exploit the thermal and mechanical capabilities of the transducer without any clipping in the amplifier stage. On the contrary, if the amplifier is pushed to its limits and shows frequent saturation, its power specification should be less than the rated Nominal Power Handling of the loudspeaker. EXCURSION LIMITS Evolution is a process that affects not only products, but also their technical specifications. Constant advances in research provide more precise methods to measure the performance of loudspeakers and describe their features. Thiele-Small parameters have become the universal language for describing loudspeaker behaviour in the small signal domain. Nevertheless, they comment little on the working limits of loudspeakers in the large signal domain. These limits are customarily indicated by Xmax, the maximum linear excursion. In a typical measurement, this value corresponds to a maximum of 0% total harmonic distortion (THD) with a sinusoidal signal (though most manufacturers, including B&C, now typically provide data for Linear Mathematical Xmax, not measured Xmax). cent research shows that this method can yield ambiguous results, and even different numerical values for the same loudspeaker. The main limit of this measurement is that it looks at the output signal instead of the physical features of the driver itself. On the contrary, the most up-to-date instruments for distortion analysis can measure the variations in loudspeaker parameters when they are fed with high-level signals. In this way,

an excursion limit can be fixed beyond which the parameter s variation becomes excessive. The Xvar value reported in our data (generally after the traditional Xmax value) is measured this way. Beyond this excursion limit, the loudspeaker force factor (), or the total suspension compliance (Cms), or both, drops to less than 50% of their small signal value, producing high distortion levels and strong variations from small signal behaviour. This new technique yields different results from the standard Xmax measurement. B&C Speakers believes that this added information gives a more accurate and reliable description of loudspeaker capabilities in actual operating conditions. QUALITY CONTROL Every product from B&C Speakers is 00% quality tested before it is packaged and shipped. We perform a set of measurements on every component to ensure that its frequency, harmonic distortion, and electrical impedance fall within established tolerance windows. Each cone loudspeaker is additionally tested using a low frequency, high-voltage acoustical sweep to check for vibrations or noises (rub and buzz). Each product is guaranteed and supported with a -year limited warranty. DC OFFSET A known issue of the dynamic loudspeaker is the instability of the average working position for frequencies above the resonance frequency. In this range, because of the phase relationship between force and position, the variations in force factor () vs position drive the moving assembly away from the maximum. Intuitively, the loudspeaker tends to slide down the slopes of the (x) curve. This is referred to as DC offset. Since the rest position is the optimal average working point, DC offset leads to several undesirable consequences: reduced excursion capabilities, increased mechanical stress, and increased distortion. These are due to the loudspeaker working in a region where nonlinearities are larger, and thermal dissipation and power handling are lower. Generally speaking, a large amount of DC offset leads to poor performance and shortened loudspeaker life. All B&C loudspeakers are designed with DC offset reduction in mind, especially our large excursion subwoofers. Our motors are designed to have a large plateau around the rest position, both through magnet assembly optimization and voice coil design. ducing the slope of the curve, especially in the central region, will reduce instability and therefore the amount of DC offset. A special winding technique has been adopted in the most critical cases. Our suspensions are also designed to counteract DC offset before it degrades performance. DC component XDC Force factor (x) (0:05:0) x [mm] -0 - - [N/A] 5 0 5 unstable stable - 0 - -5 5-6 *0 *0 5*0 6*0 7*0 8*0 9*0 0 Frequency fl [] 0-5 -0-5 0 5 0 5 <<coiloin Xd[mm] coiloout>> B&C Speakers reserves the right to change the specifications of our products without notice.

FE B&C Speakers is a major supplier to the pro audio market in midrange, woofer and subwoofer cone drivers. We have made a strong commitment to provide a well-balanced line of drivers that range in size from to. Our engineers have optimized each design with Finite Element Analysis (FEA) software to ensure each speaker operates to its fullest potential time and time again. In recent years we have made refinements to our cone geometry, magnet assemblies and speaker production lines to create a dynamic and powerful lineup of products. The models that are included in this catalog all have: From nightclubs, to stadiums, to concert halls around the world, our speakers are chosen based on their reliability, consistency and most of all for their outstanding sound quality and performance. increased increased power handling capacity increased excursion capabilities lower distortion levels bcspeakers.com

FE 5FG FE WOOFER 00 W 9 db mm (.7 in) aluminium voice coil 6-6000 Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap 7 mm (5 in) 6.5 Ω 00 W 00 W 9 db 6-6000 mm (.7 in) Copper Kapton 9 mm (0.5 in) 6 mm (0.5 in). T Ferrite Ring Front Side THIELE & SMALL PARAMET 6 5. Qes 0. Qms 0 Qts 0.7 Vas 6. dm (0. ft ) Sd 95 cm (.7 in ) η 0 0.55% ± mm ± 5 mm. g 0 T m 0.8 mh 0 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 mm (5. in) mm (5.6 in) Baffle Cutout Diameter mm (.8 in) 77 mm ( in) Flange and Gasket Thickness 9 mm (0.5 in) Air volume occupied by driver 0.5 dm (0.0 ft ).6 kg (.5 lb).85 kg (. lb) 0x0x5 mm (8.7x8.7x.9 in) RCK005FG-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 5

FE 6MD8 FE MIDRANGE 0 W 96 db 8 mm (.5 in) aluminium voice coil 50-6000 Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 70 mm (6.5 in) 6.5 Ω 0 W 0 W 96 db 50-6000 8 mm (.5 in) 9 mm (0.5 in) 6 mm (0.5 in). T Ferrite Ring Front Side THIELE & SMALL PARAMET 0 5.7 Ω Qes 0.9 Qms.7 Qts 0. Vas dm (0. ft ) Sd cm (0.5 in ) η 0.% ± mm ±.5 mm g 0.5 T m 0.5 mh 65 within the specified range -0. 87 mm (7. in) 7 mm (6.7 in) Baffle Cutout Diameter 5 mm (5.7 in) 8 mm (. in) Flange and Gasket Thickness 9 mm (0.5 in) Air volume occupied by driver 0.8 dm (0. ft ). kg (.8 lb).5 kg (5. lb) 0x0x5 mm (8.7x8.7x.9 in) Power on Continuous Program is defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCK006MD8-8 Average SPL from 500 to 6000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 6

FE 6PS8 FE WOOFER 00 W 9 db 8 mm (.5 in) aluminium voice coil 70-5000 Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in and 6 Ω, data upon request 70 mm (6.5 in) 6.6 Ω 50 W 00 W 9 db 70-5000 8 mm (.5 in) mm (0.9 in) 6 mm (0. in). T Ferrite Ring Front Side THIELE & SMALL PARAMET 75 5. Ω Qes 0. Qms.7 Qts 0. Vas 8 dm (0.8 ft ) Sd cm (0.6 in ) η 0 % ± 6 mm ± 7.5 mm g 0.8 T m 0.6 mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 87 mm (7.6 in) 7 mm (6.77 in) Baffle Cutout Diameter 5.0 mm (5.7 in) 8 mm (. in) Flange and Gasket Thickness 9 mm (0.5 in) Air volume occupied by driver 0.8 dm (0.0 ft ). kg (.85 lb).5 kg (5. lb) 0x0x5 mm (8.7x8.7x.9 in) RCK06PS88 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 7

FE 6PS FE WOOFER 00 W 9 db mm (.7 in) copper voice coil 70-5000 Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 70 mm (6.5 in) 6.0 Ω 00 W 00 W 9 db 70-5000 mm (.7 in) Copper mm (0.9 in) 6 mm (0. in). T Ferrite Ring Front Side THIELE & SMALL PARAMET 7 5. Ω Qes 0. Qms.5 Qts 0. Vas 7 dm (0.5 ft ) Sd cm (0.6 in ) η 0 0.7% ±.5 mm ± 6.0 mm 8 g T m 0.7 mh 08 within the specified range -0. 87 mm (7.6 in) 7 mm (6.77 in) Baffle Cutout Diameter 5.0 mm (5.7 in) 88 mm (.6 in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver 0.9 dm (0.0 ft ).5 kg (5.5 lb).75 kg (6.06 lb) 0x0x5 mm (8.7x8.7x.9 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCK06PS-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 8

FE 8FW5 FE WOOFER 00 W 97 db 5 mm ( in) copper voice coil 70-5000 Shorting copper cap for extended HF Ventilated voice coil gap for reduced power compression Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap 00 mm (8 in) 7. Ω 00 W 00 W 97 db 70-5000 5 mm ( in) Copper Kapton 6.5 mm (0.65 in) 0 mm (0. in).5 T Ferrite Ring Both Sides Also available in Ω and 6 Ω, data upon request THIELE & SMALL PARAMET 7 5. Ω Qes 0. Qms 9. Qts 0. Vas dm (0. ft ) Sd 0 cm (. in ) η 0. % ± 6 mm ± 5 mm 7 g 7.7 T m 0.56 mh EPB 5 within the specified range -0. 5 mm (8.8 in) 0 mm (8. in) Baffle Cutout Diameter 87 mm (7. in) 00 mm (.9 in) Flange and Gasket Thickness mm (0. in) Air volume occupied by driver.5 dm (0.05 ft ) 5. kg (.6 lb) 5.6 kg (. lb) 55x55x50 mm (0.0x0.0x5.90 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCK008FW5-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 9

FE 8FG6 FE WOOFER 600 W 9 db 6 mm (.5 in) copper voice coil 50-000 demodulating ring for very low distortion Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 00 mm (8 in) 6.7 Ω 00 W 600 W 9 db 50-000 6 mm (.5 in) Copper 9 mm (0.75 in) 0 mm (0.9 in) 0.9 T Ferrite Ring Front Side THIELE & SMALL PARAMET 5 5. Qes 0. Qms 0. Qts 0. Vas 5 dm (0.5 ft ) Sd 0 cm (. in ) η 0 0.7% ± 7 mm ± 8 mm g 5.8 T m.7 mh 59 within the specified range -0. 5 mm (8.86 in) 0 mm (8. in) Baffle Cutout Diameter 87 mm (7. in) 00 mm (.9) Flange and Gasket Thickness 9 mm (0.7 in) Air volume occupied by driver.5 dm (0.05 ft ).5 kg (9.9 lb).9 kg (0.8 lb) 55x55x50 mm (0.0x0.0x5.90 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCK008FG6-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 0

FE 0MD6 FE MID-BASS 700 W 00 db 76 mm ( in) aluminium voice coil 80-000 Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 50 mm (0 in) 7. Ω 50 W 700 W 00 db 80-000 76 mm ( in) mm (0. in) 8 mm (0. in).5 T Ferrite Ring None THIELE & SMALL PARAMET 76 5. Qes 0. Qms.8 Qts 0. Vas 0 dm (0.7 ft ) Sd 0 cm (9. in ) η 0.9 % ±.5 mm ±.5 mm g 9.6 T m. mh EPB 5 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 6 mm (0. in) 5 mm (9.6 in) Baffle Cutout Diameter 0 mm (8.8 in) mm (.9 in) Flange and Gasket Thickness mm (0.55 in) Air volume occupied by driver.6 dm (0.09 ft ) 7. kg (6. lb) 7.9 kg (7. lb) 95xx75 mm (.6x.6x6.89 in) RCK00MD6-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

FE 0FW6 FE WOOFER 500 W 98 db 6 mm (.5 in) aluminium voice coil 65-000 Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap 50 mm (0 in) 6. Ω 50 W 500 W 98 db 65-000 6 mm (.5 in) mm (0.55 in) 8 mm (0. in).5 T Ferrite Ring Front Side THIELE & SMALL PARAMET 6 5 Ω Qes 0.5 Qms. Qts 0. Vas 7 dm (0.95 ft ) Sd 0 cm (50 in ) η 0.6 % ± 5 mm ± 5.5 mm g 6. T m 0.9 mh 5 within the specified range -0. 6 mm (0. in) 5 mm (9.6 in) Baffle Cutout Diameter 0 mm (8.8 in) 6 mm (.6 in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver.5 dm (0.09 ft ) 5.9 kg ( lb) 6.5 kg (. lb) 95xx75 mm (.6x.6x6.89 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCK00FW6-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

FE MH FE MID-BASS 800 W 0 db 76 mm ( in) copper voice coil 50-000 demodulating ring for very low distortion Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 0 mm ( in) 6.5 Ω 00 W 800 W 0 db 50-000 76 mm ( in) Copper mm (0.55 in) 8 mm (0. in). T Ferrite Ring Front Side THIELE & SMALL PARAMET 5 5. Ω Qes 0. Qms 7. Qts 0.9 Vas 6 dm (. ft ) Sd 5 cm (80.9 in ) η 0.8 % ± 5 mm ± 7 mm 5 g. T m 0.8 mh 65 within the specified range -0. 6 mm (. in) 96 mm (.6 in) Baffle Cutout Diameter 8 mm (. in) mm (5. in) Flange and Gasket Thickness mm (0.7 in) Air volume occupied by driver. dm (0. ft ) 7.6 kg (6.7 lb) 8.5 kg (8.7 lb) 60x60x00 mm (.7x.7x7.87 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCK0MH-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

FE FW6 FE WOOFER 500 W 98 db 6 mm (.5 in) aluminium voice coil 55-000 Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 0 mm ( in) 6.7 Ω 50 W 500 W 98 db 55-000 6 mm (.5 in) mm (0.55 in) 8 mm (0. in). T Ferrite Ring Front Side THIELE & SMALL PARAMET 55 5. Ω Qes 0. Qms.5 Qts 0.9 Vas 6 dm (.6 ft ) Sd 5 cm (80.9 in ) η 0.6 % ± 5 mm ± 5 mm 7 g 5.5 T m mh 7 within the specified range -0. 5 mm (. in) 98 mm (.7 in) Baffle Cutout Diameter 8 mm (. in) 6 mm (5.5 in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver dm (0.0 ft ) 5.6 kg (. lb) 6.5 kg (. lb) 60x60x00 mm (.7x.7x7.87 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCKFW6-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

FE FW76 FE WOOFER 000 W 00 db 76 mm ( in) copper voice coil 55-000 demodulating ring for very low distortion Nominal (AES)¹ Continuous program² Sensitivity (W/m) Winding Magnetic Gap Also available in and 6 Ω, data upon request 0 mm ( in) 6. 500 W 000 W 00 db 55-000 76 mm ( in) Copper 9 mm (0.75 in) mm (0. in).5 T Ferrite Ring Front Side THIELE & SMALL PARAMET 5 5. Ω Qes 0.8 Qms.8 Qts 0.8 Vas 5 dm (.6 ft ) Sd 5 cm (80.9 in ) η 0.7 % ± 7 mm ± 0 mm 75 g 6. T m. mh 00 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 mm (. in) 98 mm (.7 in) Baffle Cutout Diameter 8 mm (. in) 7 mm (5.79 in) Flange and Gasket Thickness mm (0.7 in) Air volume occupied by driver dm (0.0 ft ) 8.5 kg (8.7 lb) 9. kg (0.8 lb) 60x60x00 mm (.7x.7x7.87 in) RCK0FW76-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 5

FE PLB00 FE WOOFER 00 W 97 db 00 mm ( in) aluminium voice coil 50-500 demodulating ring for very low distortion Ventilated voice coil gap for reduced power compression (50-500 ) Nominal (AES)¹ Continuous program² Sensitivity (W/m) Winding Magnetic Gap 0 mm ( in) 6 Ω 600 W 00 W 97 db 50-500 00 mm ( in) mm (0.9 in) 0 mm (0.9 in).0 T Ferrite Ring Front Side THIELE & SMALL PARAMET 50 5. Ω Qes 0.8 Qms 9. Qts 0.7 Vas 7 dm (.6 ft ) Sd 5 cm (8 in ) η 0.7 % ± 9 mm ± 7 mm 77 g 8. T m.6 mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (.5 in) 99 mm (.8 in) Baffle Cutout Diameter 8 mm (. in) mm (.8 in) Flange and Gasket Thickness mm (0.7 in) Air volume occupied by driver.5 dm (0. ft ) 9. kg (0.5 lb) 0. kg (.9 lb) 60x60x00 mm (.7x.7x7.87 in) RCKPLB00-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 6

FE PS00 FE SUBWOOFER 00 W 9 db 00 mm ( in) copper voice coil 5-000 Double silicone spider with optimized compliance Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 0 mm ( in) 6.7 Ω 700 W 00 W 9 db 5-000 00 mm ( in) Copper mm (0.8 in) mm (0. in).05 T Ferrite Ring Both Sides THIELE & SMALL PARAMET 5. Ω Qes 0.9 Qms.9 Qts 0.7 Vas 7 dm (.6 ft ) Sd 5 cm (8. in ) η 0. % ± 8 mm ± 8 mm 06 g.5 T m mh 5 within the specified range -0. 9 mm (.5 in) 99 mm (.8 in) Baffle Cutout Diameter 8 mm (. in) 8 mm (.6 in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver.5 dm (0. ft ) 8.8 kg (9. lb) 9.7 kg (.8 lb) 60x60x00 mm (.7x.7x7.87 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCKPS00-8 Average SPL from 50 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 7

FE TBX00 FE SUBWOOFER 000 W 95 db 00 mm ( in) copper voice coil 5-000 demodulating ring for very low distortion Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 0 mm (.0 in) 6. Ω 000 W 000 W 95 db 5-500 00 mm ( in) Copper 5 mm ( in) mm (/ in). T Ferrite Ring Both Sides THIELE & SMALL PARAMET 5. Ω Qes 0.7 Qms 6.9 Qts 0.6 Vas 7.5 dm (. ft ) Sd 5 cm (8. in ) η 0.5 % ± 9 mm ± mm 9 g 5.5 T m.6 mh 55 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (.5in) 99 mm (.8 in) Baffle Cutout Diameter 8 mm (. in) 5 mm (5. in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver. dm (0.5 ft ).8 kg (6 lb).7 kg (8.0 lb) 60x60x00 mm (.7x.7x7.87 in) RCKTBX00-8 Average SPL from 50 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 8

FE 5FW76 FE WOOFER 000 W 00 db 76 mm ( in) copper voice coil 0-000 demodulating ring for very low distortion Double silicone spider and ventilated voice coil gap Nominal (AES)¹ Continuous program² Sensitivity (W/m) Winding Magnetic Gap Also available in and 6 Ω, data upon request 80 mm (5 in) 6. Ω 500 W 000 W 00 db 0-000 76 mm ( in) Copper 9 mm (0.75 in) mm (0. in).5 T Ferrite Ring Front Side THIELE & SMALL PARAMET 0 5. Ω Qes 0. Qms 5. Qts 0. Vas 8 dm (.9 ft ) Sd 855 cm (.5 in ) η 0.9 % ± 7 mm ± 8 mm 7 g 6. T m. mh 8 within the specified range -0. 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 77 mm (6.97 in) Flange and Gasket Thickness mm (0.55 in) Air volume occupied by driver 5.5 dm (0.9 ft ) 9. kg (0. lb) 0.5 kg (.5 lb) 5x5x mm (6.7x6.7x8.8 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCK5FW76-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 9

FE 5PLB76 FE WOOFER 800 W 00 db 76 mm ( in) copper voice coil 0-000 Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 80 mm (5 in) 6. Ω 00 W 800 W 00 db 0-000 76 mm ( in) Copper 6 mm (0.6 in) mm (0. in).5 T Ferrite Ring Both Sides THIELE & SMALL PARAMET 5.0 Ω Qes 0.6 Qms 5.9 Qts 0.5 Vas 6 dm (5.8 ft ) Sd 855 cm (.5 in ) η 0.5 % ± 5 mm ± 8 mm 88 g. T m. mh 6 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (5.5in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 69 mm (6.65 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 5. dm (0.8 ft ) 8.5 kg (8.7 lb) 9.8 kg (.6 in) 5x5x mm (6.7x6.7x8.8 in) RCK5PBL76-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 0

FE 5PS00 FE SUBWOOFER 00 W 95.0 db 00 mm ( in) copper voice coil 5-500 Double silicone spider with optimized compliance Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 80 mm (5 in) 6.5 Ω 700 W 00 W 95.0 db 5-500 00 mm ( in) Copper mm (0.8 in) mm (0. in).05 T Ferrite Both Sides THIELE & SMALL PARAMET 9 5. Ω Qes 0.7 Qms 6.0 Qts 0. Vas 0.0 dm (.6 ft ) Sd 855.0 cm (.5 in ) η 0.5 % ± 8 mm ± 6.5 mm 60 g. T m.0 mh 8 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 68 mm (6.6 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 6. dm (0. ft ) 9.8 kg (.5 lb). kg (. lb) 5x5x mm (6.7x6.7x8.86 in) RCK5PS00-8 Average SPL from 50 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

FE 5PZB00 FE SUBWOOFER 00 W 97 db 00 mm ( in) copper voice coil 0-000 Double silicone spider with optimized compliance Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 80 mm (5 in) 6. Ω 700 W 00 W 97 db 0-000 00 mm ( in) Copper mm (0.8 in) 9 mm (0.5 in).5 T Ferrite Ring Both Sides THIELE & SMALL PARAMET 9 5. Ω Qes 0. Qms 6.5 Qts 0.9 Vas 0 dm (,8 ft ) Sd 855 cm (.5 in ) η 0. % ± 8 mm ± 6.5 mm 5 g 5.8 T m mh 0 within the specified range -0. 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 7 mm (6.6 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 5. dm (0.8 ft ).8 kg (6 lb). kg (8.8 lb) 5x5x mm (6.7x6.7x8.8 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCK5PZB00-8 Average SPL from 50 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

FE 5RBX00 FE SUBWOOFER 000 W 95 db 00 mm ( in) copper voice coil 0-000 demodulating ring for very low distortion Double silicone spider with optimized compliance Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 80 mm (5 in) 6. Ω 000 W 000 W 95 db 0-000 00 mm ( in) Copper 5 mm ( in) mm (0. in). T Ferrite Ring Both Sides THIELE & SMALL PARAMET 5. Ω Qes 0. Qms 5.65 Qts 0.8 Vas 00 dm (.5 ft ) Sd 908 cm (0.7 in ) η 0.0 % ± 9 mm ± 0 mm 5 g.0 T m. mh 0 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 7 mm (6.8 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 5.0 dm (0.8 ft ).7 kg (5.8 lb) kg (8.66 lb) 5x 5x mm (6.7x6.7x8.86 in) RCK5RBX00-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

FE 5TBX00 FE SUBWOOFER 000 W 96 db 00 mm ( in) copper voice coil 5-500 Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression demodulating ring for very low distortion Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 80 mm (5 in) 6. Ω 000 W 000 W 96 db 5-500 00 mm ( in) Copper 5 mm ( in) mm (/in). T Ferrite Ring Both Sides THIELE & SMALL PARAMET 5 5. Ω Qes 0. Qms 5. Qts 0.8 Vas dm (.8 ft ) Sd 855 cm (.5 in ) η 0.95 % ± 9 mm ± mm 6 g 5.5 T m.6 mh 6 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 8 mm (7. in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 5. dm (0.9 ft ). kg (7. lb).6 kg (9.98 lb) 5x5x mm (6.7x6.7x8.8 in) RCK5TBX00-8 Average SPL from 50 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

FE 5TBW00 FE SUBWOOFER 000 W 96 db 00 mm ( in) split winding copper voice coil 0-500 Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression demodulating ring for very low distortion 57 mm peak-to-peak excursion before damage Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 80 mm (5 in) 6.7 Ω 500 W 000 W 96 db 0-500 00 mm ( in) Copper mm (. in) 5 mm (0.59 in).5 T Ferrite Ring Both Sides THIELE & SMALL PARAMET 9 5. Ω Qes 0. Qms. Qts 0. Vas 96 dm (.9 ft ) Sd 855 cm (.5 in ) η 0.6 % ± mm ±.5 mm 8 g 6. T m. mh 8 within the specified range -0. 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 9 mm (7.5 in) Flange and Gasket Thickness mm (0.55 in) Air volume occupied by driver 6 dm (0. ft ). kg (.5 lb) 5.6 kg (.9 lb) 5x5x mm (6.7x6.7x8.8 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCK5TBW00-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 5

FE 8PS00 FE SUBWOOFER 00 W 95.5 db 00 mm ( in) copper voice coil 0-000 Double silicone spider with optimized compliance Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 60 mm (8 in) 6. Ω 700 W 00 W 95.5 db 0-000 00 mm ( in) Copper mm (0.8 in) mm (0. in).05 T Ferrite Ring Both Sides THIELE & SMALL PARAMET 0 5. Ω Qes 0. Qms.6 Qts 0.9 Vas 5 dm (8.6 ft ) Sd 0 cm (87.6 in ) η 0.6 % ± 8 mm ± 8 mm 0 g.5 T m. mh 7 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 60 mm (8 in) 0 mm (7. in) Baffle Cutout Diameter mm (6.6 in) 97 mm (7.75 in) Flange and Gasket Thickness 6 mm (5/8 in) Air volume occupied by driver 9.5 dm (0. ft ) 0.5 kg (. lb).9 kg (6. lb) 500x95x75 mm (9.68x9.8x0.8 in) RCK8PS00-8 Average SPL from 50 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 6

FE 8PZB00 FE SUBWOOFER 00 W 97 db 00 mm ( in) split winding copper voice coil 0-000 Double silicone spider with optimized compliance Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 60 mm (8 in) 6.5 Ω 700 W 00 W 97 db 0-000 00 mm ( in) Copper mm (0.8 in) 8 mm (0. in).5 T Ferrite Ring Both Sides THIELE & SMALL PARAMET 0 5. Ω Qes 0.5 Qms 8.8 Qts 0. Vas 97 dm (0.5 ft ) Sd cm (75.8 in ) η 0. % ± 8 mm ± 8 mm 70 g 6 T m. mh 0 within the specified range -0. 60 mm (8 in) 0 mm (7. in) Baffle Cutout Diameter mm (6.6 in) 0 mm (7.95 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 9.5 dm (0. ft ). kg (6.6 lb) kg (0.8 lb) 500x95x75 mm (9.68x9.8x0.8 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCK8PZB00-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 7

FE 8RBX00 FE SUBWOOFER 000 W 97 db 00 mm ( in) copper voice coil 5-000 demodulating ring for very low distortion Double silicone spider with optimized compliance Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 60 mm (8 in) 6. Ω 000 W 000 W 97 db 5-000 00 mm ( in) Copper 5 mm (.0 in) mm (0. in). T Ferrite Ring Both Sides THIELE & SMALL PARAMET 0 5. Ω Qes 0.6 Qms 7. Qts 0. Vas 0 dm (7.77 ft ) Sd 5 cm (89.88 in ) η 0. % ± 0 mm ± mm 99 g 5. T m.5 mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 60 mm (8. in) 0 mm (7. in) Baffle Cutout Diameter mm (6.6 in) 00 mm (7.87 in) Flange and Gasket Thickness mm (0.55 in) Air volume occupied by driver 0.5 dm (0.7 ft ). kg (7. lb).9 kg (0.6 lb) 500x95x75 mm (9.68x9.8x0.8 in) RCK8RBX00-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 8

FE 8TBX00 FE SUBWOOFER 00 W 97 db 00 mm ( in) copper voice coil 5-000 Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression demodulating ring for very low distortion Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in and 6 Ω, data upon request 60 mm (8 in) 6. Ω 00 W 00 W 97 db 5-000 00 mm ( in) Copper 5 mm ( in) mm (0.5 in). T Ferrite Ring Both Sides THIELE & SMALL PARAMET 5. Ω Qes 0.7 Qms 7. Qts 0.5 Vas dm (7.5 ft ) Sd 0 cm (87.6 in ) η 0. % ± 9 mm ± mm 09 g 5.5 T m.6 mh 9 within the specified range -0. 60 mm (8 in) 0 mm (7. in) Baffle Cutout Diameter mm (6.6 in) 09 mm (8. in) Flange and Gasket Thickness 6 mm (5/8 in) Air volume occupied by driver 0.5 dm (0.7 ft ) kg (8.6 lb). kg (.7 lb) 500x95x75 mm (9.68x9.8x0.8 in) defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. RCK8TBX00-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 9

FE 8TBW00 FE SUBWOOFER 000 W 96 db 00 mm ( in) split winding copper voice coil 5-000 Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression demodulating ring for very low distortion 57 mm peak-to-peak excursion before damage Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 60 mm (8 in) 6.5 Ω 500 W 000 W 96 db 5-000 00 mm ( in) Copper mm (. in) 5 mm (0.59 in).5 T Ferrite Ring Both Sides THIELE & SMALL PARAMET 5 5. Ω Qes 0. Qms 8 Qts 0.9 Vas 75 dm (6.8 ft ) Sd 0 cm (87.6 in ) η 0.76 % ± mm ± mm 5 g 6. T m.5 mh 85 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V 60 mm (8 in) mm (7. in) Baffle Cutout Diameter mm (6.6 in) mm (9.5 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver dm (0.9 ft ) 5. kg (. lb) 6.8 kg (7 lb) 500x95x75 mm (9.68x9.8x0.8 in) RCK8TBW00-8 for 8 ohms. Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 0

B&C is a leader in the development of neodymium woofers for the professional audio market. Our HPL series, launched in 998, was one of the first neodymium loudspeakers available. We have since expanded our use of neodymium to cover our entire range. In addition to having optimized frequency curves, our newer woofers feature baskets that have been designed to maximize power handling, excursion, and heat dissipation. The L series works with an inside slug high-energy neodymium magnet. It has been developed with a new ventilated magnet assembly to assist the cooling of the voice coil. L series woofers strike a balance between light weight and performance. The MDN and MBX series are specifically designed for high output MidBass applications, especially in compact enclosures. The more recent MBX parameters offer an ideal solution for two way systems, but are also an excellent choice for multi-driver applications, such as Line Array enclosures. The MBX series combines high, linearity and excellent power handling. Low moving mass enables a precise and fast transient attack. Other features include a dedicated demodulation ring, ventilated voice coil gap, and new hydrophobic cone surface, offering extreme protection without increased moving mass. The NBX and NW series feature a very highenergy neodymium magnet assembly. A specially designed double silicone spider offers excellent excursion control. The SW series is the next generation of neodymium magnet subwoofers. We focused our energy on long, large diameter voice coils ( to 6 ) for greater power handling and low power compression. In addition, we have developed new suspension systems to offer superb linearity with low DC offset, and industry-leading durability. The most recent DS Series feature high motors with four layer aluminium voice coils, for high subwoofer applications. bcspeakers.com

5F6 FULL RANGE 60 W 88 db 6 mm ( in) aluminium voice coil 00-0000 Neodymium magnet allows a very light yet powerful motor assembly OEM Quantities Only 90 mm (.5 in) 6. Ω Nominal (AES) 0 W Continuous Program 60 W Sensitivity (W/m) 88 db 00-0000 6 mm (.0 in) Kapton Winding 8 mm (0. in) Magnetic Gap mm (0. in). T Neodymium Inside Slug None Also available in 6 Ω, data upon request THIELE & SMALL PARAMET 98 6.0 Ω Qes 0.58 Qms 8.8 Qts 0.55 Vas.9 dm (0.07 ft ) Sd 6 cm (7. in ) η 0 0. % ±. mm ±.9 mm g 5. T m 0.6 mh 68 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8v for 8 ohms. 07 mm (. in) 96 mm (.78 in) Baffle Cutout Diameter 8.5 mm (. in) 50 mm (.97 in) Flange and Gasket Thickness mm (0. in) Air volume occupied by driver 0.5 dm (0.0 ft ) 0.8 kg (0. lb) (8 units) 8.75 kg (9.9 lb) (8 units) 5 X 5 X 50 mm (6.7 X.9 X 9.8 in) Average SPL from 00 to 7000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

F FULL RANGE 00 W 88 db mm (. in) copper voice coil 0-8000 Neodymium magnet allows a very light yet powerful motor assembly OEM Quantities Only 00 mm (.0 in) 6. Ω Nominal (AES) 00 W Continuous Program 00 W Sensitivity (W/m) 88 db 0-8000 mm (. in) Copper Winding mm (0. in) Magnetic Gap 7 mm (0.8 in).5 T Neodymium Inside Slug None THIELE & SMALL PARAMET 0 5.5 Ω Qes 0.7 Qms. Qts 0.8 Vas.6 dm (0.06 ft ) Sd 57 cm (8.8 in ) η 0 0.7 % ±.8 mm ± 5.7 mm 6 g 9.0 T m 0. mh 07 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 7 mm (5.0 in) 5 mm (.5 in) Baffle Cutout Diameter 0.0 mm (.06 in) 66 mm (.6 in) Flange and Gasket Thickness mm (0.0 in) Air volume occupied by driver 0.5 dm (0.0 ft ) 0.5 kg (.9 lb) ( units). (8.88 lb) ( units) 5 X 5 X 50 mm (6.7 X.9 X 9.8 in) Average SPL from 500 to 5000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

5MDN8 MIDRANGE 00 W 96 db 8 mm (.5 in) copper voice coil 0-0000 Shorting copper cap for extended HF Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 7 mm (5 in) 7.0 Ω 00 W 00 W 96 db 0-0000 8 mm (.5 in) 0 mm (0. in) 6 mm (0. in).5 T Neodymium Ring Front Side THIELE & SMALL PARAMET 0 5.6 Ω Qes 0.5 Qms.6 Qts 0.5 Vas 0.6 dm (0.0 ft ) Sd 95 cm (.7 in ) η 0.7 % ±.5 mm ±.5 mm 9 g.5 T m 0. mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8v for 8 ohms. 50 mm (5.9 in) mm (5.6 in) Baffle Cutout Diameter mm (.8 in) 75 mm (.95 in) Flange and Gasket Thickness 9 mm (0.5 in) Air volume occupied by driver 0.5 dm (0.0 ft ) 0.85 kg (.9 lb).05 kg (. lb) 0x0x5 mm (8.7x8.7x.9 in) RCK005MDN8-8 Average SPL from 00 to 7000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

5NSM8 MIDRANGE 0 W 99 db 8 mm (.5 in) aluminium voice coil 00-500 Ideal for Direct Radiation and Horn Loaded Midrange application demodulating ring for very low distortion Hydrophobic Cone treatment Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 7 mm (5.0 in) 6. Ω 0 W 0 W 99 db 00-500 8 mm (.5 in) 7 mm (0.8 in) 6 mm (0. in).5 T Neodymium Ring Impregnated Cone THIELE & SMALL PARAMET 00 5. Ω Qes 0.99 Qms. Qts 0.79 Vas 0. dm (0.0 ft ) Sd 95 cm (.7 in ) η 0.5 % ±. mm ±.0 mm 9 g 0. T m 0.5 mh 0 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 57 mm (6.8 in) mm (5.59 in) Baffle Cutout Diameter mm ( in) 08 mm (.5 in) Flange and Gasket Thickness 9 mm (0.5 in) Air volume occupied by driver. dm (0.0 ft ).7 kg (.0 lb).8kg (.0 lb) 55x55x50 mm (0.0x0.0x5.90 in) RCK005NSM8-8 Average SPL from 500 to 5000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 5

5L8 WOOFER 80 W 9 db 8 mm (.5 in) copper voice coil 80-7000 Shorting copper cap for extended HF Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 7 mm (5 in) 6. Ω 90 W 80 W 9 db 80-7000 8 mm (.5 in) 0 mm (0.7 in) 6 mm (0. in).5 T Neodymium Ring Front Side THIELE & SMALL PARAMET 80 5.5 Ω Qes 0.7 Qms 9. Qts 0.6 Vas. dm (0.5 ft ) Sd 95 cm (.7 in ) η 0 0.55 % ±.5 mm ±.0 mm g 9. T m 0.6 mh 6 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8v for 8 ohms. Average 50 mm (5.9 in) mm (5.6 in) Baffle Cutout Diameter.0 mm (.8 in) 75 mm (.95 in) Flange and Gasket Thickness 9 mm (0.5 in) Air volume occupied by driver 0.5 dm (0.0 ft ) 0.85 kg (.9 lb).05 kg (. lb) 0x0x5 mm (8.7x8.7x.9 in) RCK005L8-8 SPL from 00 to 7000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 6

6MDN MIDRANGE 00 W 96.5 db mm (.7 in) aluminium voice coil 50-6000 Ventilated voice coil gap for reduced power compression Neodymium magnet allows a very light yet powerful motor assembly demodulating ring for very low distortion Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 70 mm (6.5 in) 6.5 Ω 00 W 00 W 96.5 db 50-6000 mm (.7 in) 0 mm (0.7 in) 6 mm (0.5 in).5 T Neodymium Ring Front Side THIELE & SMALL PARAMET 0 5. Ω Qes 0.6 Qms.8 Qts 0.0 Vas.7 dm (0.09 ft ) Sd cm (0.5 in ) η 0.6 % ±.5 mm ±.0 mm g T m 0.7 mh 0 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 87 mm (7. in) 7 mm (6.7 in) Baffle Cutout Diameter 5 mm (5.7 in) 7 mm (.9 in) Flange and Gasket Thickness mm (0. in) Air volume occupied by driver 0.6 dm (0.0 ft ).0 kg (. lb).5 kg (.75 lb) 0x0x5 mm (8.7x8.7x.9 in) RCK06MDN-8 Average SPL from 500 to 5000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 7

6MBX WOOFER 00 W 98 db mm (.7 in) aluminium voice coil 5-5000 Neodymium magnet allows a very light yet powerful motor assembly demodulating ring for very low distortion Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 70 mm (6.5 in) 6 Ω 00 W 00 W 98 db 5-5000 mm (.7 in) 0 mm (0.7 in) 6 mm (0.5 in).55 T Neodymium Ring Impregnated Cone THIELE & SMALL PARAMET 5. Ω Qes 0. Qms.9 Qts 0. Vas. dm (0. ft ) Sd cm (0.6 in ) η 0. % ±.5 mm ±.0 mm g.7 T m 0. mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 87 mm (7.6 in) 7 mm (6.7 in) Baffle Cutout Diameter 5 mm (5.7 in) 87 mm (. in) Flange and Gasket Thickness mm (0. in) Air volume occupied by driver 0.6 dm (0.0 ft ).5 kg (. lb).75 kg (.86 lb) 0x0x5 mm (8.7x8.7x.9 in) RCK06MBX -8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 8

6L8 WOOFER 00 W 9 db 8 mm (.5 in) copper voice coil 70-6000 Neodymium magnet allows a very light yet powerful motor assembly demodulating ring allows a very low distortion Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in and 6 Ω, data upon request 70 mm (6.5 in) 6 Ω 50 W 00 W 9 db 70-6000 8 mm (.5 in) Copper Kapton mm (0.5 in) 6 mm (0.5 in).5 T Neodymium Ring Front Side THIELE & SMALL PARAMET 7 5. Ω Qes 0. Qms.5 Qts 0. Vas 7 dm (0.5 ft ) Sd cm (0.5 in ) η 0 0.6 % ± 6 mm ± 5.5 mm 7 g 9.5 T m 0.6 mh 6 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 87 mm (7. in) 7 mm (6.7 in) Baffle Cutout Diameter 5 mm (5.7 in) 85 mm (. in) Flange and Gasket Thickness mm (0. in) Air volume occupied by driver 0.6 dm (0.0 ft ). kg (.6 lb).5 kg (. lb) 0x0x5 mm (8.7x8.7x.9 in) RCK06L8-8 Average SPL from 500 to 5000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 9

8MDN5 WOOFER 00 W 97 db 5 mm ( in) copper voice coil 70-000 Neodymium ring magnet assembly Ventilated voice coil gap for reduced power compression Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in and 6 Ω, data upon request 00 mm (8 in) 7.7 Ω 00 W 00 W 97 db 70-000 5 mm ( in) Kapton 6 mm (0.6 in) 8 mm (0. in).5 T Neodymium Ring Front Side THIELE & SMALL PARAMET 70 5. Ω Qes 0. Qms.7 Qts 0. Vas 6 dm (0.6 ft ) Sd 0 cm (. in ) η 0.% ± 6 mm ± 6 mm g 5. T m 0.8 mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 mm (8.8 in) 0 mm (8. in) Baffle Cutout Diameter 87 mm (7. in) 95 mm (.7 in) Flange and Gasket Thickness mm (0. in) Air volume occupied by driver. dm (0.0 ft ).55 kg (5.6 lb).0 kg (6.6 lb) 50x50x5 mm (9.8x9.8x.9 in) RCK008MDN5-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 0

8MBX5 WOOFER 00 W 96.5 db 5 mm ( in) copper voice coil 60-000 Neodymium ring magnet assembly demodulating ring for very low distortion Ventilated voice coil gap for reduced power compression Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 00 mm (8 in) 5.9 Ω 00 W 00 W 96.5 db 60-000 5 mm ( in) 5 mm (0.59 in) 7 mm (0.8 in). T Neodymium Ring Impregnated Cone THIELE & SMALL PARAMET 60.9 Ω Qes 0. Qms 5.6 Qts 0.9 Vas dm (0.8 ft ) Sd 0 cm (. in ) η 0.7 % ± 6 mm ± 8 mm 0 g. T m 0. mh 9 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 mm (8.86 in) 0 mm (8.7 in) Baffle Cutout Diameter 87 mm (7.6 in) 9 mm (.7 in) Flange and Gasket Thickness 9 mm (0.5 in) Air volume occupied by driver. dm (0.0 ft ).8 kg (.97 lb).5 kg (.96 in) 55x55x50 mm (0.0x0.0x5.90 in) RCK008MBX5-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

8NSM6 MIDRANGE 500 W 00 db 6 mm (.5 in) aluminium voice coil 5-000 Ideal for Direct Radiation and Horn Loaded Midrange application demodulating ring for very low distortion Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in 6 Ω, data upon request 00 mm (8 in) 8. Ω 50 W 500 W 00 db 5-000 6 mm (.5 in) Aluminum mm (0.5 in) 0 mm (0.9 in).55 T Neodymium Ring Front Side THIELE & SMALL PARAMET 5 5.7 Ω Qes 0.5 Qms 9. Qts 0. Vas.5 dm (0.05 ft ) Sd 0 cm (. in ) η 0.5 % ±.0 mm ±.7 mm 9 g T m 0.6 mh 700 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (9. in) mm (8.7 in) Baffle Cutout Diameter 00 mm (7.87 in) 5 mm (.5 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver.5 dm (0. ft ).85 kg (0.69 lb) 5.5 kg (.0 lb) 95xx75 mm (.6x.6x6.89 in) RCK008NSM6-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

8L5 WOOFER 00 W 9 db 5 mm ( in) copper voice coil 65-000 Neodymium magnet allows a very light yet powerful motor assembly Shorting copper cap for extended HF Ventilated voice coil gap for reduced power compression 00 mm (8 in) 6.6 Ω Nominal (AES) 00 W Continuous Program 00 W Sensitivity (W/m) 9 db 65-000 5 mm ( in) Copper Winding 7 mm (0.67 in) Magnetic Gap 8 mm (0. in).05 T Neodymium Inside Slug Both Sides Also available in and 6 Ω, data upon request THIELE & SMALL PARAMET 66 5. Ω Qes 0. Qms.6 Qts 0.7 Vas dm (0.9 ft ) Sd 0 cm (. in ) η 0 % ± 7 mm ± 7 mm 8 g. T m 0.5 mh 60 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 mm (8.8 in) 0 mm (8. in) Baffle Cutout Diameter 87 mm (7. in) 90 mm (.5 in) Flange and Gasket Thickness mm (0. in) Air volume occupied by driver. dm (0.0 ft ).8 kg ( lb).5 kg (.96 lb) 55x55x50 mm (0.0x0.0x5.90 in) RCK008L5-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

8NW5 WOOFER 00 W 96.5 db 5 mm ( in) copper voice coil 70-000 Neodymium ring magnet allows a very high force factor and linear excursion Shorting copper cap for extended HF Ventilated voice coil gap for reduced power compression Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in and 6 Ω, data upon request 00 mm (8 in) 7.7 Ω 00 W 00 W 96.5 db 70-000 5 mm ( in) Copper 9 mm (0.75 in) 0 mm (0. in). T Neodymium Ring Both Sides THIELE & SMALL PARAMET 7 5. Ω Qes 0.9 Qms.7 Qts 0.7 Vas dm (0. ft ) Sd 0 cm (. in ) η 0. % ± 6 mm ± 6 mm 8 g 8.9 T m 0. mh 89 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 mm (8.8 in) 0 mm (8. in) Baffle Cutout Diameter 87 mm (7. in) 00 mm ( in) Flange and Gasket Thickness mm (0. in) Air volume occupied by driver. dm (0.0 ft ) kg (6.6 lb).5 kg (7.6 lb) 55x55x50 mm (0.0x0.0x5.90 in) RCK008NW5-8 Average SPL from 00 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com

8L6 WOOFER 700 W 97 db 6 mm (.5 in) copper voice coil 80-000 Neodymium inside slug magnet assembly Shorting copper cap for extended HF Ventilated voice coil gap for reduced power compression 00 mm (8 in) 7. Ω Nominal (AES) 50 W Continuous Program 700 W Sensitivity (W/m) 97 db 80-000 6 mm (.5 in) Copper Winding mm (0.55 in) Magnetic Gap 8 mm (0. in).5 T Neodymium Inside Slug Front Side Also available in 6 Ω, data upon request THIELE & SMALL PARAMET 80 5. Ω Qes 0.5 Qms 0.9 Qts 0.5 Vas 9.6 dm (0. ft ) Sd 0 cm (. in ) η 0.88 % ±.5 mm ± 5.0 mm 8 g 7.5 T m 0.6 mh 0 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 mm (8.8 in) 0 mm (8. in) Baffle Cutout Diameter 87 mm (7. in) 95 mm (.7 in) Flange and Gasket Thickness 0 mm (0.9 in) Air volume occupied by driver.5 dm (0.05 ft ).8 kg (6.7 lb).5 kg (7.7 lb) 55x55x50 mm (0.0x0.0x5.90 in) RCK008L6-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 5

8BG5 WOOFER 500 W 9 db 5 mm ( in) copper voice coil 50-000 Neodymium magnet allows a very light yet powerful motor assembly Shorting copper cap for extended HF Ventilated voice coil gap for reduced power compression 00 mm (8 in) 6.0 Ω Nominal (AES) 50 W Continuous Program 500 W Sensitivity (W/m) 9 db 50-000 5 mm ( in) Copper Winding 7 mm (0.65 in) Magnetic Gap 8 mm (0. in).5 T Neodymium Inside Slug Front Side Also available in 6 Ω, data upon request THIELE & SMALL PARAMET 5 5. Ω Qes 0. Qms. Qts 0. Vas 8 dm (0.6 ft ) Sd 0 cm (. in ) η 0 0.6 % ± 6.5 mm ± 8.0 mm 5 g.8 T m 0.5 mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 mm (8.8 in) 0 mm (8. in) Baffle Cutout Diameter 87 mm (7. in) 90 mm (.5 in) Flange and Gasket Thickness mm (0. in) Air volume occupied by driver. dm (0.0 ft ).8 kg (.0 lb).5 kg (.96 lb) 55x55x50 mm (0.0x0.0x5.90 in) RCK008BG5-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 6

0MBX6 MIDBASS 700 W 99 db 6 mm (.5 in) aluminium voice coil 65-6000 Neodymium inside slug magnet assembly demodulating ring for very low distortion Ventilated voice coil gap for reduced power compression 50 mm (0 in) 6.5 Ω Nominal (AES) 50 W Continuous Program 700 W Sensitivity (W/m) 99 db 65-6000 6 mm (.5 in) Winding mm (0.5 in) Magnetic Gap 8 mm (0. in).5 T Neodymium Inside Slug Impregnated Cone Also available in 6 Ω, data upon request THIELE & SMALL PARAMET 65 5. Ω Qes 0.8 Qms.0 Qts 0.6 Vas 6 dm (0.9 ft ) Sd 6 cm (5.6 in ) η 0. % ±.5 mm ± 5.0 mm g 7. T m 0. mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 6 mm (0.8 in) 5 mm (9.6 in) Baffle Cutout Diameter 0 mm (9 in) 5 mm (.9 in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver.5 dm (0.05 ft ). kg (7.05 lb).8 kg (8.8 lb) 95xx75 mm (.6x.6x6.89 in) RCK0MBX6-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 7

0NSM76 MIDRANGE 800 W 00 db 76 mm ( in) aluminium voice coil 5-500 Ideal for Direct Radiation and Horn Loaded Midrange application 50 mm (0 in) 7.0 Ω Nominal (AES) 00 W Continuous Program 800 W Sensitivity (W/m) 00 db 5-500 76 mm ( in) Winding mm (0.5 in) Magnetic Gap 9 mm (0.5 in).6 T Neodymium Inside Slug Front Side THIELE & SMALL PARAMET 5 5. Ω Qes 0.55 Qms 8.6 Qts 0.5 Vas dm (0.07 ft ) Sd 0 cm (9.6 in ) η 0.5 % ±.5 mm ±.5 mm g.5 T m 0.9 mh 7 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (.6 in) 7 mm (0.79 in) Baffle Cutout Diameter mm (9. in) 0 mm (5. in) Flange and Gasket Thickness mm (0.7 in) Air volume occupied by driver 5.0 dm (0.8 ft ).75 kg (8.7 lb).65 kg (0.5 lb) 60x60x00 mm (.7x.7x7.87 in) RCk0NSM76-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 8

0HPL6 WOOFER 00 W 98.5 db 6 mm (.5 in) aluminium voice coil 60-000 Neodymium magnet allows a very light yet powerful motor assembly 50 mm (0 in) 6. Ω Nominal (AES) 00 W Continuous Program 00 W Sensitivity (W/m) 98.5 db 60-000 6 mm (.5 in) Winding mm (0.7 in) Magnetic Gap 8 mm (0. in).5 T Neodymium Inside Slug None Also available in 6 Ω, data upon request THIELE & SMALL PARAMET 6 5. Ω Qes 0. Qms.5 Qts 0. Vas dm (. ft ) Sd 0 cm (50 in ) η 0.5 % ± mm ± 5.5 mm 9 g 5 T m 0.5 mh 8 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 6 mm (0. in) 5 mm (9.6 in) Baffle Cutout Diameter 0 mm (9. in) mm (.8 in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver.5 dm (0.05 ft ) kg (. lb).6 kg (5.7 lb) 95xx75 mm (.6x.6x6.89 in) RCK00HPL6-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 9

0L6 WOOFER 500 W 97 db 6 mm (.5 in) aluminium voice coil 50-000 Neodymium magnet allows a very light yet powerful motor assembly Ventilated voice coil gap for reduced power compression 50 mm (0 in) 7 Ω Nominal (AES) 50 W Continuous Program 500 W Sensitivity (W/m) 97 db 50-000 6 mm (.5 in) Winding mm (0.55 in) Magnetic Gap 8 mm (0. in).5 T Neodymium Inside Slug Both Sides Also available in and 6 Ω, data upon request THIELE & SMALL PARAMET 56 5.7 Ω Qes 0.9 Qms. Qts 0.6 Vas dm (. ft ) Sd 0 cm (9. in ) η 0.8 % ± 6 mm ± 7 mm 7 g 6. T m 0.9 mh 9 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 6 mm (0. in) 5 mm (9.6 in) Baffle Cutout Diameter 0 mm (8.8 in) mm (. in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver.5 dm (0.05 ft ).9 kg (6. lb).5 kg (7.7 lb) 95xx75 mm (.6x.6x6.89 in) RCK0L6-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 50

0NW6 WOOFER 600 W 96 db 6 mm (.5 in) copper voice coil 50-500 Neodymium magnet allows a very light yet powerful motor assembly Shorting copper cap for extended HF Ventilated voice coil gap for reduced power compression 50 mm (0 in) 6.5 Ω Nominal (AES) 00 W Continuous Program 600 W Sensitivity (W/m) 96 db 50-500 6 mm (.5 in) Copper Winding 6 mm (0.6 in) Magnetic Gap 8 mm (0. in).5 T Neodymium Inside Slug Both Sides Also available in and 6 Ω, data upon request THIELE & SMALL PARAMET 50 5. Ω Qes 0.7 Qms.5 Qts 0.6 Vas 7.5 dm (0.95 ft ) Sd 0 cm (50.0 in ) η 0. % ± 8 mm ± 0 mm 7 g 7.5 T m 0.7 mh 85 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 6 mm (0. in) 5 mm (9.6 in) Baffle Cutout Diameter 0 mm (9. in) mm (. in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver.5 dm (0.05 ft ).9 kg (6. lb).5 kg (7.7 lb) 95xx75 mm (.6x.6x6.89 in) RCK0NW6-8 Average SPL from 50 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 5

CL76 WOOFER 700 W 98.5 db 76 mm ( in) copper voice coil 5-000 Ventilated voice coil gap for reduced power compression 0 mm ( in) 6.5 Ω Nominal (AES) 50 W Continuous Program 700 W Sensitivity (W/m) 98.5 db 5-000 76 mm (.0 in) Copper Winding 7 mm (0.67 in) Magnetic Gap mm (0. in).05 T Neodymium Inside Slug Front Side Also available in 6 Ω, data upon request THIELE & SMALL PARAMET 8 5. Ω Qes 0. Qms.8 Qts 0. Vas 59 dm (. ft ) Sd 5 cm (80.9 in ) η 0.9 % ± 6.0 mm ± 8.5 mm 70 g. T m.5 mh 8 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. mm (. in) 99 mm (.77 in) Baffle Cutout Diameter 8 mm (. in) mm (5.59 in) Flange and Gasket Thickness 9 mm (0.5 in) Air volume occupied by driver. dm (0.08 ft ).0 kg (6.6 lb).9 kg (8.6 lb) 60x60x00 mm (.7x.7x7.87 in) RCKCL76-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 5

L76 WOOFER 800 W 00 db 76 mm ( in) aluminium voice coil 50-000 Neodymium magnet allows a very light yet powerful motor assembly Ventilated voice coil gap for reduced power compression 0 mm ( in) 6. Ω Nominal (AES) 00 W Continuous Program 800 W Sensitivity (W/m) 00 db 50-000 76 mm ( in) Winding 9 mm (0.75 in) Magnetic Gap 0 mm (0. in).5 T Neodymium Inside Slug Both Sides Also available in and 6 Ω, data upon request THIELE & SMALL PARAMET 50 5. Ω Qes 0. Qms. Qts 0. Vas 7 dm (.5 ft ) Sd 5 cm (80.9 in ) η 0. % ± 7.0 mm ± 6.5 mm 5 g 0. T m.0 mh 8 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 mm (. in) 98 mm (.7 in) Baffle Cutout Diameter 8 mm (. in) mm (5.5 in) Flange and Gasket Thickness mm (0.55 in) Air volume occupied by driver.5 dm (0.08 ft ).9 kg (8.6 lb).8 kg (0.58 lb) 60x60x00 mm (.7x.7x7.87 in) RCKL76-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 5

NW76 WOOFER 000 W 98.5 db 76 mm ( in) aluminium voice coil 0-000 Neodymium ring magnet allows a very high force factor and linear excursion demodulating ring for very low distortion Ventilated voice coil gap for reduced power compression Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in and 6 Ω, data upon request 0 mm ( in) 6.9 Ω 500 W 000 W 98.5 db 0-000 76 mm ( in) Copper 9 mm (0.75 in) mm (0. in). T Neodymium Ring Both Sides THIELE & SMALL PARAMET 0 5. Ω Qes 0.7 Qms.7 Qts 0.6 Vas 76 dm (.7 ft ) Sd 5 cm (80.9 in ) η 0.8 % ± 8 mm ± 0 mm 77 g 5.5 T m.5 mh 5 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 mm (. in) 98 mm (.7 in) Baffle Cutout Diameter 8 mm (. in) 7 mm (5.8 in) Flange and Gasket Thickness mm (0.55 in) Air volume occupied by driver.5 dm (0.08 ft ).9 kg (0.8 lb) 5.8 kg (.79 lb) 60x60x00 mm (.7x.7x7.87 in) RCKNW76-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 5

L88 WOOFER 00 W 98 db 88 mm (.5 in) aluminium voice coil 50-000 0 mm ( in) 6 Ω Nominal (AES) 700 W Continuous Program 00 W Sensitivity (W/m) 98 db 50-000 88 mm (.5 in) Winding mm (0.85 in) Magnetic Gap 0 mm (0. in).5 T Neodymium Inside Slug Front Side Also available in and 6 Ω, data upon request THIELE & SMALL PARAMET 5 5 Ω Qes 0.9 Qms 5 Qts 0.7 Vas 5 dm (.8 ft ) Sd 5 cm (80.9 in ) η 0. % ± 8 mm ± 9.5 mm 7 g 9.9 T m. mh 75 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 mm (. in) 98 mm (.7 in) Baffle Cutout Diameter 8 mm (. in) 0 mm (5.5 in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver.5 dm (0.08 ft ).8 (0.58 lb) 5.7 kg (.57 lb) 60x60x00 mm (.7x.7x7.87 in) RCKL88-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 55

BG00 SUBWOOFER 000 W 9 db 00 mm ( in) copper voice coil 0-000 demodulating ring for very low distortion FEA optimized Neodymium magnet assembly Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression 0 mm ( in) Minumum Impedance 5. Nominal (AES) 000 W Continuous Program 000 W Sensitivity (W/m) 9 db 0-000 00 mm ( in) Copper Winding 7 mm (.06 in) Magnetic Gap mm (0. in).5 T Neodymium Inside Slug Both Sides Also available in and 6 Ω, data upon request THIELE & SMALL PARAMET 9 5. Ω Qes 0.5 Qms 6.8 Qts 0. Vas dm (.5 ft ) Sd 5 cm (80.9 in ) η 0 0.7 % ± 0.5 mm ± mm 5 g T m.6 mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (.5 in) 99 mm (.8 in) Baffle Cutout Diameter 8 mm (. in) 7 mm (5. in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver.7 dm (0.09 ft ) 8. kg (8 lb) 9. kg (0.06) 60x60x00 mm (.7x.7x7.87 in) RCKBG00-8 Average SPL from 50 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 56

NBX00 SUBWOOFER 000 W 96 db 00 mm ( in) aluminium voice coil 0-500 demodulating ring for very low distortion FEA optimized Neodymium magnet assembly Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 0 mm ( in) 6.5 Ω 000 W 000 W 96 db 0-500 00 mm ( in) Copper 5 mm ( in) mm (0. in). T Neodymium Ring Both Sides THIELE & SMALL PARAMET 5. Ω Qes 0. Qms.9 Qts 0. Vas 5 dm (.8 ft ) Sd 5 cm (8 in ) η 0.5 % ± 0 mm ± 0 mm 7 g 5.6 T m.9 mh 70 Also available NBX 00 - within the specified range -0. defined as db greater then the Applied RMS Voltage is set to.8 V 0 mm (.6 in) 00 mm (.8 in) Baffle Cutout Diameter 80 mm ( in) mm (5.6 in) Flange and Gasket Thickness mm (0.7 in) Air volume occupied by driver dm (0. ft ) 8 kg (7.6 lb) 8.9 kg (9.6 lb) 60x60x00 mm (.7x.7x7.87 in) RCKNBX00-8 for 8 ohms. Average SPL from 50 to 00. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 57

L76 WOOFER 000 W 99 db 76 mm ( in) copper voice coil 0-000 Very light yet powerful motor assembly demodulating ring for very low distortion 59 mm ( in) Minumum Impedance 6. Ω Nominal (AES) 500 W Continuous Program 000 W Sensitivity (W/m) 99 db 0-000 76 mm ( in) Copper Winding mm (0.8 in) Magnetic Gap 0 mm (0. in).5 T Neodymium Inside Slug Front Side THIELE & SMALL PARAMET 5 Ω Qes 0. Qms 8. Qts 0. Vas dm (. ft ) Sd 707 cm (09.59 in ) η 0.7 % ± 8 mm ± 9.5 mm 85 g 9 T m. mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 59 mm (. in) mm (.5 in) Baffle Cutout Diameter mm (.7 in) 6 mm ( 6. in) Flange and Gasket Thickness mm (0.7 in) Air volume occupied by driver dm (0. ft ).5 kg (9.9 lb) 5.8 kg (.79 lb) 5x5x mm (6.7x6.7x8.8 in) RCKL76-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 58

L88 WOOFER 00 W 99 db 88 mm (.5 in) aluminium voice coil 5-000 Very light yet powerful motor assembly demodulating ring for very low distortion 59 mm ( in) 6.5 Ω Nominal (AES) 700 W Continuous Program 00 W Sensitivity (W/m) 99 db 5-000 88 mm (.5 in) Winding mm (0.85 in) Magnetic Gap 0 mm (0. in).5 T Neodymium Inside Slug Front Side Also available in and 6 Ω, data upon request THIELE & SMALL PARAMET 5 5 Ω Qes 0. Qms 7.8 Qts 0. Vas 0 dm (.6 ft ) Sd 707 cm (09.6 in ) η 0.9 % ± 8 mm ± 9.5 mm 86 g 9.9 T m. mh 5 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 59 mm (. in) mm (.5 in) Baffle Cutout Diameter mm (.7 in) 67 mm (6.57 in) Flange and Gasket Thickness mm (0.7 in) Air volume occupied by driver.5 dm (0. ft ).7 kg (0.6 lb) 6.0 kg (. lb) 5x5x mm (6.7x6.7x8.8 in) RCKL88-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 59

5L76 WOOFER 000 W 99.5 db 76 mm ( in) copper voice coil 0-000 Neodymium magnet allows a very light yet powerful motor assembly Ventilated voice coil gap for reduced power compression 80 mm (5 in) 6.7 Ω Nominal (AES) 500 W Continuous Program 000 W Sensitivity (W/m) 99.5 db 0-000 76 mm ( in) Copper Winding 8 mm (0.68 in) Magnetic Gap 0.5 mm (0. in).5 T Neodymium Inside Slug Both Sides Also available in Ω, data upon request THIELE & SMALL PARAMET 7 5. Ω Qes 0. Qms.5 Qts 0. Vas 95 dm (6.8 ft ) Sd 855 cm (.5 in ) η 0. % ± 7 mm ± 9 mm 96 g.5 T m.5 mh 5 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 7 mm (6.7 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver.5 dm (0. ft ).6 kg (0. lb) 5.9 kg ( lb) 5x5x mm (6.7x6.7x8.8 in) RCK5L76-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 60

5NW76 WOOFER 00 W 00.5 db 76 mm ( in) aluminium voice coil 0-000 demodulating ring for very low distortion Neodymium ring magnet allows a very high force factor and linear excursion Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in and 6 Ω, data upon request 80 mm (5 in) 6.9 Ω 600 W 00 W 00.5 db 0-000 76 mm ( in) Copper 9 mm (0.75 in) mm (0. in). T Neodymium Ring Both Sides THIELE & SMALL PARAMET 5. Ω Qes 0. Qms. Qts 0. Vas 0 dm (.5 ft ) Sd 855 cm (.5 in ) η 0. % ± 8 mm ± 0 mm 0 g 5.5 T m.5 mh 8 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 77 mm (7.0 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver.7 dm (0. ft ) 5.6 kg (. lb) 7 kg (5. lb) 5x5x mm (6.7x6.7x8.8 in) RCK5NW76-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 6

5L88 WOOFER 00 W 99 db 88 mm (.5 in) aluminium voice coil 5-000 Double silicone spider with optimized compliance demodulating ring for very low distortion Neodymium magnet allows a very light yet powerful motor assembly 80 mm (5 in) 6 Ω Nominal (AES) 700 W Continuous Program 00 W Sensitivity (W/m) 99 db 5-000 88 mm (.5 in) Winding mm (0.85 in) Magnetic Gap 0 mm (0.9 in).5 T Neodymium Inside Slug Front Side Also available in and 6 Ω, data upon request THIELE & SMALL PARAMET 5 5 Ω Qes 0.6 Qms 6. Qts 0. Vas 6 dm (.5 ft ) Sd 855 cm (.5 in ) η 0. % ± 8 mm ± 0 mm 0 g 0. T m.5 mh 5 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 77 mm (6.97 in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver.5 dm (0. ft ).6 kg (0. lb) 5.9 kg ( lb) 5x5x mm (6.7x6.7x8.8 in) RCK5L88-8 Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 6

5NA00 WOOFER 600 W 98 db 00 mm ( in) aluminium voice coil 5-000 FEA optimized Neodymium magnet assembly Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression 80 mm (5 in) 6.6 Ω Nominal (AES) 800 W Continuous Program 600 W Sensitivity (W/m) 98 db 5-000 00 mm ( in) Winding mm (0.9 in) Magnetic Gap mm (0. in). T Neodymium Inside Slug Front Side THIELE & SMALL PARAMET 7 5. Ω Qes 0.9 Qms 6. Qts 0.8 Vas 88 dm (. ft ) Sd 855 cm (.5 in ) η 0.9 % ± 0 mm ± 9 mm 6 g 6. T m. mh 6 within the specified range -0. Continuous Program Power is defined as db greater than the Applied RMS Voltage is set to.8v for 8 ohms. 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 80 mm (7.09 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 6 dm (0. ft ) 9. kg (0.5 lbs) 0.6 kg (.7 lb) 5x5x mm (6.7x6.7x8.8 in) RCK5NA00-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 6

5BG00 SUBWOOFER 000 W 9.5 db 00 mm ( in) copper voice coil 5-000 demodulating ring for very low distortion FEA optimized Neodymium magnet assembly Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression 80 mm ( in) Minumum Impedance 6 Ω Nominal (AES) 000 W Continuous Program 000 W Sensitivity (W/m) 9.5 db 5-000 00 mm ( in) Copper Winding 7 mm (.06 in) Magnetic Gap mm (0. in).5 T Neodymium Inside Slug Both Sides Also available in Ω, data upon request THIELE & SMALL PARAMET 6 5. Ω Qes 0.9 Qms 5.0 Qts 0. Vas 8 dm (.9 ft ) Sd 855 cm (.5 in ) η 0 0.8 % ± 0.5 mm ± mm 0 g T m.6 mh 7 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. Average SPL from 00 to 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 89 mm (7.5 in) Flange and Gasket Thickness mm (0.9 in) Air volume occupied by driver 6 dm (0. ft ) 8.6 kg (8.9 lb) 9.9 kg (.8 lb) 5x5x mm (6.7x6.7x8.8 in) RCK5BG00-8 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 6

5NBX00 SUBWOOFER 000 W 97 db 00 mm ( in) copper voice coil 5-500 FEA optimized Neodymium magnet assembly demodulating ring for very low distortion Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 80 mm (5 in) 6. Ω 000 W 000 W 97 db 5-500 00 mm ( in) Copper 5 mm (.0 in) mm (0. in). T Neodymium Ring Both Sides THIELE & SMALL PARAMET 6 5. Ω Qes 0. Qms. Qts 0.9 Vas 5 dm (. ft ) Sd 855 cm (.5 in ) η 0 % ± 0 mm ± 0 mm 5 g 5 T m mh 6 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (5.5 in) 7 mm (6.7 in) Baffle Cutout Diameter 5 mm (.9 in) 79 mm (7.05 in) Flange and Gasket Thickness mm (0.55 in) Air volume occupied by driver 6 dm (0. ft ) 9 kg (9.8 lb) 0. kg (. lb) 5x5x mm (6.7x6.7x8.8 in) RCK5NBX00-8 Average SPL from 50 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 65

5SW00 SUBWOOFER 000 W 95 db 00 mm ( in) split winding copper voice coil 0-500 Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression demodulating ring for very low distortion 57 mm peak-to-peak excursion before damage 80 mm (5 in) 6.5 Ω Nominal (AES) 500 W Continuous Program 000 W Sensitivity (W/m) 95 db 0-500 00 mm ( in) Copper Winding mm (.6 in) Magnetic Gap 6 mm (0.6 in).5 T Neodymium Inside Slug Both Sides Also available in Ω, data upon request THIELE & SMALL PARAMET 7 5. Ω Qes 0. Qms.8 Qts 0. Vas 0 dm (.9 ft ) Sd 855 cm (.5 in ) η 0.6 % ±.5 mm ± mm 76 g 5.6 T m. mh 08 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 90 mm (7.5 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 6 dm (0. ft ) 9.5 kg ( lb) 0.8 kg (.8 lb) 5x5x mm (6.7x6.7x8.8 in) RCK5SW00-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 66

5SW5 SUBWOOFER 00 W 96 db 6 mm (.5 in) split winding copper voice coil 5-500 Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression demodulating ring for very low distortion 60 mm peak-to-peak excursion before damage 80 mm (5 in) 6.5 Ω Nominal (AES) 700 W Continuous Program 00 W Sensitivity (W/m) 96 db 5-500 6 mm (.5 in) Copper Winding mm (. in) Magnetic Gap mm (0.55 in).5 T Neodymium Inside Slug Both Sides Also available in Ω, data upon request THIELE & SMALL PARAMET 5 5. Ω Qes 0.5 Qms. Qts 0. Vas 0 dm (.9 ft ) Sd 855 cm (.5 in ) η 0.8 % ±.5 mm ± mm 00 g 0 T m.8 mh 0 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 9 mm (5.5 in) 7 mm (6.7 in) Baffle Cutout Diameter 5 mm (.9 in) 9 mm (7.6 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 7 dm (0.5 ft ) kg (6. lb). kg (9. lb) 5x5x mm (6.7x6.7x8.8 in) RCK5SW5-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 67

8NBX00 SUBWOOFER 00 W 96.5 db 00 mm ( in) split winding copper voice coil 5-000 Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression demodulating ring for very low distortion 57 mm peak-to-peak excursion before damage Nominal (AES) Continuous Program Sensitivity (W/m) Winding Magnetic Gap Also available in Ω, data upon request 60 mm (8 in) 6 Ω 00 W 00 W 96.5 db 5-000 00 mm ( in) Copper 5 mm ( in) mm (0. in). T Neodymium Ring Both Sides THIELE & SMALL PARAMET 5 5. Ω Qes 0. Qms 5.6 Qts 0.8 Vas 98 dm (7 ft ) Sd 0 cm (87.6 in ) η 0 % ± 0 mm ± mm 7 g.8 T m.85 mh 87 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 60 mm (8 in) 0 mm (7. in) Baffle Cutout Diameter mm (6.6 in) 08 mm (8.9 in) Flange and Gasket Thickness mm (0.55 in) Air volume occupied by driver 8.5 dm (0.0 ft ) 9. kg (0.5 lb) 0.9 kg (.0 lb) 500x95x75 mm (9.68x9.8x0.8 in) RCK8NBX00-8 Average SPL from 00 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 68

8NW00 SUBWOOFER 00 W 98 db 00 mm ( in) copper voice coil 5-000 FEA optimized Neodymium magnet assembly allows the highest force factor and excursion capability Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression 60 mm (8 in) 6. Ω Nominal (AES) 00 W Continuous Program 00 W Sensitivity (W/m) 98 db 5-000 00 mm ( in) Copper Winding 5 mm ( in) Magnetic Gap mm (0.5 in). T Neodymium Inside Slug Both Sides Also available in Ω, data upon request THIELE & SMALL PARAMET 5. Ω Qes 0.7 Qms. Qts 0.6 Vas 5 dm (8.9 ft ) Sd 0 cm (87.6 in ) η 0.7 % ± 9 mm ± mm g 8 T m.7 mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 60 mm (8 in) 0 mm (7. in) Baffle Cutout Diameter mm (6.6 in) 09 mm (8. in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 8.5 dm (0.0 ft ) 9. kg (0.5 lb) 0.9 kg (.0 lb) 500x95x75 mm (9.68x9.8x0.8 in) RCK8NW00-8 Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 69

8SW00 SUBWOOFER 000 W 97 db 00 mm ( in) split winding copper voice coil 5-000 demodulating ring for very low distortion Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression 57 mm peak-to-peak excursion before damage 60 mm (8 in) Minumum Impedance 6.5 Ω Nominal (AES) 500 W Continuous Program 000 W Sensitivity (W/m) 97 db 5-000 00 mm ( in) Copper Winding mm (.6 in) Magnetic Gap mm (0.55 in).5 T Neodymium Inside Slug Both Sides Also available in Ω, data upon request THIELE & SMALL PARAMET 5 5. Ω Qes 0. Qms 5.9 Qts 0.8 Vas 80 dm (6. ft ) Sd 0 cm (87.6 in ) η 0.9 % ±.5 mm ± 6 mm g 6. T m. mh 87 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 60 mm (8 in) mm (7. in) Baffle Cutout Diameter mm (6.6 in) 9 mm (9. in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 0 dm (0.5 ft ) 0 kg ( lb).8 kg (6.0 lb) 500x500x00 mm (9.68x9.68x.8 in) RCK8SW00-8 Average SPL from 00 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 70

8SW5 SUBWOOFER 00 W 97 db 6 mm (.5 in) split winding copper voice coil 5-500 Double silicone spider with optimized compliance Ventilated voice coil gap fpr reduced power compression demodulating ring for very low distortion 60 mm peak-to-peak excursion before damage 60 mm (8 in) 6.5 Ω Nominal (AES) 700 W Continuous Program 00 W Sensitivity (W/m) 97 db 5-500 6 mm (.5 in) Copper Winding mm (. in) Magnetic Gap mm (0.55 in).6 T Neodymium Inside Slug Both Sides Also available in Ω, data upon request THIELE & SMALL PARAMET 5. Ω Qes 0. Qms 5.6 Qts 0. Vas 87.0 dm (6.5 ft ) Sd 0 cm (87.6 in ) η 0.9 % ± mm ± 6 mm 75 g 0. T m.9 mh 00 within the specified range -0. Continuous Program Power is defined as db greater than the Applied RMS Voltage is set to.8v for 8 ohms. 60 mm (8 in) mm (7. in) Baffle Cutout Diameter mm (6.6 in) mm (9.5 in) Flange and gasket thickness 6 mm (0.6 in) Air volume occupied by driver 0.5 dm (0.7 ft ).7 Kg (0. lb).9 kg (0.6 lb) 500x500x00 mm (9.68x9.68x.8 in) RCK8SW5-8 Average SPL from 50 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 7

8DS5 SUBWOOFER Preliminary data 00 W 98 db 6 mm (.5 in) split four layer winding aluminium voice coil 0-500 Neodymium magnet allows a very high force factor and linear excursion Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression demodulating ring for very low distortion 60 mm peak-to-peak excursion before damage 00 60 mm (8 in) Minumum Impedance 7 Ω Nominal (AES) 700 W Continuous Program 00 W Sensitivity (W/m) 98 db 0-500 6 mm (.5 in) Winding 0 mm (.57 in) Magnetic Gap mm (0.55 in) 0.8 T Neodymium Inside Slug Both Sides Also available in Ω, data upon request THIELE & SMALL PARAMET 0 5.0 Ω Qes 0. Qms. Qts 0. Vas 68 dm (5.9 ft ) Sd 0 cm (87.6 in ) η 0. % ± 6.5 mm ± mm 0 g 9 T m.85 mh within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 60 mm (8 in) 0 mm (7. in) Baffle Cutout Diameter mm (6.6 in) mm (9.5 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 0 dm (0.5 ft ) kg (6.6 lb).6 kg (9.98 lb) 500x95x75 mm (9.68x9.8x0.8 in) RCK8DS5-8 Average SPL from 00 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 7

8IPAL SUBWOOFER 00 W 97 db 6 mm (.5 in) split winding aluminium voice coil - 000 Neodymium magnet allows a very high force factor and linear excursion Ventilated voice coil gap for reduced power compression Available to oem manufacturers only 80 mm peak-to-peak excursion before damage 60 mm (8 in) Ω. Ω Nominal (AES) 700 W Continuous Program 00 W Sensitivity (W/m) 97 db - 000 6 mm (.5 in) Winding mm (.7 in) Magnetic Gap mm (0.7 in).5 T Neodymium Inside Slug Both Sides THIELE & SMALL PARAMET. Ω Qes 0. Qms. Qts 0. Vas 6 dm (5.8 ft ) Sd 0 cm (87.6 in ) η 0. % ± 0.0 mm ± 5 mm 0 g.5 T m 0.65 mh 8 within the specified range -0. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 60 mm (8.0 in) mm (7. in) Baffle Cutout Diameter mm (6.6 in) 6 mm (0.8 in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 0.5 dm (0.7 ft ) 6.6 kg (6.6 lb) 8.9 kg (,67 lb) 570x570x0 mm (.x.x.60 in) RCK8IPALM Average SPL from 00 to 000. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 7

DS5 SUBWOOFER 00 W 99 db 6 mm (.5 in) four layer winding aluminium voice coil 0-000 Neodymium magnet allows a very high force factor and linear excursion Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression demodulating ring for very low distortion 60 mm peak-to-peak excursion before damage 00 50 mm ( in) 6.5 Ω Nominal (AES) 700 W Continuous Program 00 W Sensitivity (W/m) 99 db 0-000 6 mm (.5 in) Winding 6 mm (. in) Magnetic Gap mm (0.55 in) 0.8 T Neodymium Inside Slug Both Sides Also available in Ω, data upon request THIELE & SMALL PARAMET 0 5. Ω Qes 0. Qms 0.0 Qts 0. Vas 69.0 dm (9.5 ft ) Sd 680 cm (60. in ) η 0.0 % ± 5 mm ± 6.5 mm 07 g 0.8 T m.6 mh 5 within the specified range -0. defined as db greater then the Applied RMS Voltage is set to.8 V for 8 ohms. 57 mm (.5 in) 57 mm (0.7 in) Baffle Cutout Diameter 508 mm (0 in) 55 mm (0.0 in) Flange and Gasket Thickness mm (0.5 in) Air volume occupied by driver 5 dm (0.5 ft ).8 kg (.6 lb) 7. kg (7.9 lb) 570x570x0 mm (.x.x.60 in) RCKDS5-8 Average SPL from 00 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 7

SW5 SUBWOOFER 000 W 96 db 5 mm (6 in) split winding copper voice coil 0-000 Double silicone spider with optimized compliance Ventilated voice coil gap for reduced power compression demodulating ring for very low distortion 60 mm peak-to-peak excursion before damage 50 mm ( in) Ω. Ω Nominal (AES) 000 W Continuous Program 000 W Sensitivity (W/m) 96 db 0-000 5 mm (6 in) Copper Winding 0 mm (.8 in) Magnetic Gap mm (0.5 in). T Neodymium Inside Slug Both Sides Also available in 8 6 Ω, data upon request THIELE & SMALL PARAMET. Ω Qes 0. Qms 7.0 Qts 0. Vas 00.0 dm (7.0 ft ) Sd 680 cm (60. in ) η 0. % ± 5 mm ± 6 mm 60 g.5 T m.5 mh 0 within the specified range -0. defined as db greater then the Applied RMS Voltage is set to.8 V for 8 ohms. 57 mm (.5 in) 57 mm (0.7 in) Baffle Cutout Diameter 508 mm (0 in) 6 mm (0. in) Flange and Gasket Thickness 6 mm (0.6 in) Air volume occupied by driver 6 dm (0.56 ft ) 8.5 kg (0.7 lb) 0.8 kg (5.86 lb) 570x570x0 mm (.x.x.60 in) RCKSW5- Average SPL from 00 to 500. Thiele-Small parameters are measured after a high level 0 sine wave preconditioning test. bcspeakers.com 75

FE COAX IALS Coaxial loudspeakers combine the features of our best cone loudspeakers and compression drivers into a one-piece, pointsource solution. Their format enables electroacoustical designers to build very compact, versatile systems. The majority of our more recent FCX and FHX series coaxial designs feature a single magnet structure for both the woofer and high frequency driver. This solution offers a more compact, lightweight, and cost effective solution than dual driver coaxial alternatives, with little or no impact on overall performance. All coaxial loudspeaker cones are treated with a protective waterproof coating and a fine mesh HF driver protection screen, allowing operation in a wide range of environments. The waveguides loaded on the compression drivers are designed in accordance with the latest theories, resulting in uniform angular coverage and high acoustical load, with very low distortion. Many of our coaxial loudspeakers are available in alternative impedance configurations. Please ask your B&C representative for more information. bcspeakers.com 76

FE COAX IALS 5FCX FE- COAXIAL 00 W 9 db 70 nominal coverage 60-8000 Nom. Diameter 7 mm (5 in) Nom. Impedance 6.5 Ω (), 6.5 Ω (HF) 60-8000 Dispersion Angle 70 Ferrite ()/Neo Ring (HF) Waterproof cone treatment Front side UNIT Sensitivity (W/m) 9 db Nom. (AES) 00 W Continuous Program 00 W mm (.7 in) Copper.07 T Kapton Winding 9.0 mm (0.5 in) Magnetic Gap 6.0 mm (0. in) HF UNIT Sensitivity (W/m) 07.5 db Nom. (AES) 0 W Continuous Program 0 W Diaphragm Material commended Crossover 5 Inductance Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. 5 mm (.5 in) Polyester.5 k.65 T 0. mh 6 mm (5.5 in) mm (5.6 in) Baffle Cutout Diameter mm (.8 in) 0 mm (. in) Flange and Gasket Thickness 8 mm (0. in).85 kg (. lb). kg (.85 lb) 55x55x50 mm (0.0x0.0x5.90 in) HF - Two hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. THIELE & SMALL PARAMET 6 5.6 Ω Qes 0.5 Qms 7.8 Qts 0.5 Vas 7 dm (0.5 ft ) Sd 95 cm (.7 in ) η 0 0.6 % ± mm ± 5 mm g 0.5 T m 0.8 mh HF RCK005FCX-8 MMDDE5-8 defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 77

FE COAX IALS 6FHX5 FE- COAXIAL 00 W 9 db 70 nominal coverage 85-8000 Nom. Diameter 70 mm (6.5 in) Nom. Impedance 6.5 Ω (), 7 Ω (HF) 85-8000 Dispersion Angle 70 Ferrite ()/Neo Ring (HF) Waterproof cone treatment Front side UNIT Sensitivity (W/m) 9 db Nom. (AES) 50 W Continuous Program 00 W 5 mm ( in) Copper.05 T Kapton Winding.0 mm (0,5 in) Magnetic Gap 6.0 mm (0. in) HF UNIT Sensitivity (W/m) 08.5 db 0 W Continuous Program 0 W Diaphragm Material commended Crossover 5 Inductance Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. 5 mm ( in) Polyester.5 k.65 T 0. mh 87 mm (7. in) 7 mm (6.7 in) Baffle Cutout Diameter 6 mm (5.75 in) mm (.8 in) Flange and Gasket Thickness mm (0.7 in).7 kg (5.9 lb).05 kg (6.7 lb) 55x55x50 mm (0.0x0.0x5.90 in) HF - Two hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. THIELE & SMALL PARAMET 85 5.5 Ω Qes 0. Qms 7.8 Qts 0.7 Vas 5 dm (0.8 ft ) Sd cm (0.5 in ) η 0 0.8 % ± 5 mm ± 5.7 mm 6 g. T m mh HF RCK06FHX5-8 MMDDE5-8 defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 78

FE COAX IALS 8CX FE COAXIAL 00 W 9 db 00 nominal coverage 75-0000 Nom. Diameter 0 mm (8 in) Nom. Impedance 6. Ω (), 7. Ω (HF) 75-0000 Dispersion Angle 00 Ferrite Ring Waterproof cone treatment None UNIT Sensitivity (W/m) 9 db Nom. (AES) 00 W Continuous Program 00 W 5 mm (.0 in) Copper. T Kapton Winding 6.0 mm (0.6 in) Magnetic Gap 8.0 mm (0. in) HF UNIT Sensitivity (W/m) 0 db Nom. (AES) 5 W Continuous Program 50 W Diaphragm Material commended Crossover 5 Inductance Also available in 6 Ω, data upon request Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. 5 mm (.0 in) Polyester.5 k.5 T 0. mh 5 mm (8.8 in) 0 mm (8. in) Baffle Cutout Diameter 87 mm (7. in) 5 mm (5. in) Flange and Gasket Thickness mm (0. in).0 kg (8.8 lb).7 kg (0. lb) 95xx75 mm (.6x.6x6.89 in) HF - Two hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. THIELE & SMALL PARAMET 7 5. Ω Qes 0.9 Qms. Qts 0.6 Vas 5 dm (0.55 ft ) Sd 0 cm (. in ) η 0.5 % ± 5 mm ± 5.5 mm g.5 T m. mh 89 HF RCK008CX-8 MMD0-8 defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 79

FE COAX IALS 8FCX5 FE COAXIAL 500 W 96 db 00 nominal coverage 69-8000 Single ferrite magnet assembly Nom. Diameter 0 mm (8 in) Nom. Impedance 6 Ω (), 7 Ω (HF) 69-8000 Dispersion Angle 00 Ferrite Ring Waterproof cone treatment Front side UNIT Sensitivity (W/m) 96 db Nom. (AES) 50 W Continuous Program 500 W 5 mm ( in).0 T Winding 7.5 mm (0.69 in) Magnetic Gap 8.0 mm (0. in) HF UNIT Sensitivity (W/m) 0 db 50 W Continuous Program 00 W Diaphragm Material commended Crossover 5 Inductance mm (.7 in) Polyimide.8 k.8 T 0. mh 5 mm (8.8 in) 0 mm (8. in) Baffle Cutout Diameter 87 mm (7. in) 8 mm (.6 in) Flange and Gasket Thickness 0 mm (0.7 in) 5. kg (. lb) 5.6 kg (. lb) 95xx75 mm (.6x.6x6.89 in) Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. THIELE & SMALL PARAMET 69.9 Ω Qes 0.6 Qms 6. Qts 0. Vas 6 dm (0.56 ft ) Sd 0 cm (. in ) η 0. % ± 6.5 mm ± 6 mm g.5 T m 0.9 mh 9 HF HF - Two hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. RCK008FCX-8 MMD00-8 defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 80

FE COAX IALS 0FCX6 FE COAXIAL 500 W 95 db 70 nominal coverage 65-8000 Single ferrite magnet assembly Nom. Diameter 50 mm (0 in) Nom. Impedance 6. Ω (), 7 Ω (HF) 65-8000 Dispersion Angle 70 Ferrite Ring Waterproof cone treatment Front side UNIT Sensitivity (W/m) 95 db Nom. (AES) 50 W Continuous Program 500 W 6 mm (.5 in) Copper 0.96 T Kapton Winding.0 mm (0.5 in) Magnetic Gap 8.0 mm (0. in) HF UNIT Sensitivity (W/m) 0 db Nom. (AES) 80 W Continuous Program 60 W Diaphragm Material commended Crossover 5 Inductance Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. 65 mm (.5 in) Titanium. k.6 T 0.5 mh 6 mm (0. in) 5 mm (9.6 in) Baffle Cutout Diameter 0 mm (8.8 in) 0 mm (5.5 in) Flange and Gasket Thickness.5 mm (0.5in) 5.65 kg (.8 lb) 6.5 kg (. lb) 60x60x00 mm (.7x.7x7.87 in) HF - Two hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. THIELE & SMALL PARAMET 6 5.5 Ω Qes 0. Qms 7.9 Qts 0. Vas 5 dm (0.89 ft ) Sd 0 cm (9. in ) η 0. % ± 5.5 mm ± 6 mm 6.5 g. T m. mh HF RCK0FCX6-8 MMD60TN-8M defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 8

FE COAX IALS FHX76 FE COAXIAL 700 W 98 db 60 x 0 nominal coverage 5-8000 Modified exponential horn flare for improved acoustic loading and controlled coverage Single ferrite magnet assembly Nom. Diameter 0 mm (6.5 in) Nom. Impedance 6 Ω (), 7. (HF) 5-8000 Dispersion Angle 60 x 0 Ferrite Ring Waterproof cone treatment Front side UNIT Sensitivity (W/m) 98 db Nom. (AES) 50 W Continuous Program 700 W 76 mm ( in) Copper.0 T Winding 6.5 mm (0.65 in) Magnetic Gap 8.0 mm (0. in) HF UNIT Sensitivity (W/m) 06 db Nom. (AES) 80 W Continuous Program 60 W 75 mm ( in) Diaphragm Material Titanium commended Crossover 5. k.8 T Inductance 0. mh 5 mm (. in) 98 mm (.7 in) Baffle Cutout Diameter 8 mm (. in) 69 mm (6.65 in) Flange and Gasket Thickness mm (0.5 in) 8.5 kg (8.7 lb) 0. kg (.7 lb) 5x5x mm (6.7x6.7x8.8 in) Also available in Ω, data upon request Also available FCX76 (without horn/ 80 disp.) Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. THIELE & SMALL PARAMET 8 5. Ω Qes 0.6 Qms 5. Qts 0. Vas 88 dm (. ft ) Sd 5 cm (80.9 in ) η 0.7 % ± 6.5 mm ± mm 7 g. T m.6 mh HF HF - Two hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. RCKFHX76-8 MMDBTN-8M defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 8

FE COAX IALS 5FCX76 FE COAXIAL 800 W 98 db 80 nominal coverage 0-8000 Single ferrite magnet assembly Nom. Diameter 80 mm (6.5 in) Nom. Impedance 6 Ω (), 7. (HF) 0-8000 Dispersion Angle 80 Ferrite Ring Waterproof cone treatment Front side UNIT Sensitivity (W/m) 98 db Nom. (AES) 00 W Continuous Program 800 W 76 mm ( in) Copper.0 T Winding 6.5 mm (0.65 in) Magnetic Gap 8.0 mm (0. in) HF UNIT Sensitivity (W/m) 05 db Nom. (AES) 80 W Continuous Program 60 W Diaphragm Material commended Crossover 5 Inductance 75 mm ( in) Titanium. k.9 T 0. mh 9 mm (5.5 in) 7 mm (6.7 in) Baffle Cutout Diameter 5 mm (.9 in) 99 mm (7.8 in) Flange and Gasket Thickness 6 mm (0.6 in) 9 kg (9.8 lb) 9.7 kg (. lb) 500x95x75 mm (9.68x9.8x0.8 in) Also available 5FHX76 (with 60 x 0 horn) Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. THIELE & SMALL PARAMET 0 5. Ω Qes 0.7 Qms 8. Qts 0. Vas 87 dm (6.6 ft ) Sd 855 cm (.5 in ) η 0.5 % ± 6.5 mm ± 7.5 mm 87 g 5.6 T m. mh 85 HF HF - Two hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. RCK5FCX76-8 MMDBTN-8M defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 8

COAX IALS Coaxial loudspeakers combine the features of our best cone loudspeakers and compression drivers into a one-piece, pointsource solution. Their format enables electroacoustical designers to build very compact, versatile systems. The majority of our more recent FCX and FHX series coaxial designs feature a single magnet structure for both the woofer and high frequency driver. This solution offers a more compact, lightweight, and cost effective solution than dual driver coaxial alternatives, with little or no impact on overall performance. All coaxial loudspeaker cones are treated with a protective waterproof coating and a fine mesh HF driver protection screen, allowing operation in a wide range of environments. The waveguides loaded on the compression drivers are designed in accordance with the latest theories, resulting in uniform angular coverage and high acoustical load, with very low distortion. Many of our coaxial loudspeakers are available in alternative impedance configurations. Please ask your B&C representative for more information. bcspeakers.com 8 bcspeakers.com 8

COAX IALS CXN6 COAXIAL Preliminary data 00 W 88 db 70 nominal coverage 00-8000.5 mm (0.85 ) HF unit exit diameter Neodymium magnet allows a very light yet powerful motor assembly demodulating ring for very low distortion Nom. Diameter 00 mm ( in) Nom. Impedance 6. Ω (), 6.5 Ω (HF) 00-8000 Dispersion Angle 70 Neodymium Inside Slug None UNIT Sensitivity (W/m) 88 db Nom. (AES) 00 W Continuous Program 00 W mm (. in) Copper.0 T Winding.0 mm (0. in) Magnetic Gap 6.0 mm (0. in) HF UNIT Sensitivity (W/m) 99 db Nom. (AES) 5 W Continuous Program 50 W Diaphragm Material commended Crossover 5 Inductance 6 mm (. in) HT Polymer.0 k.8 T 0. mh 7 mm (5.0 in) mm (.9 in) Baffle Cutout Diameter 0 mm (.06 in) 80 mm (.5 in) Flange and Gasket Thickness mm (0.0 in) 0.55 kg (. lb) 0.75 kg (.65 lb) 0x0x5 mm (8.7x8.7x.9 in) Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. THIELE & SMALL PARAMET 99 5.5 Ω Qes 0.76 Qms.5 Qts 0.7 Vas.9 dm (0.07 ft ) Sd 56.0 cm (8.68 in ) η 0 0.5 % ± mm ± 5 mm 6 g 5. T m 0.8 mh 0 HF HF - Two hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. RCK0CXN76-8 MMDDE0-8 defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 85

COAX IALS 6HCX5 COAXIAL 00 W 9 db 70 nominal coverage 90-8000 Single Neodymium magnet assembly Nom. Diameter 70 mm (6.5 in) Nom. Impedance 6 Ω (), 7.5 Ω (HF) 90-8000 Dispersion Angle 70 Neodymium Ring Waterproof cone treatment Front side UNIT Sensitivity (W/m) 9 db Nom. (AES) 50 W Continuous Program 00 W 5 mm ( in) Copper. T Kapton Winding.0 mm (0.5 in) Magnetic Gap 6.0 mm (0. in) HF UNIT Sensitivity (W/m) 05 db Nom. (AES) 5 W Continuous Program 50 W Diaphragm Material commended Crossover 5 Inductance 6 mm (. in) Polyester. k.8 T 0.06 mh 87 mm (7. in) 7 mm (6.7 in) Baffle Cutout Diameter 6 mm (5.7 in) 0 mm (. in) Flange and Gasket Thickness mm (0. in).55 kg (. lb).0 kg (. lb) 55x55x50 mm (0.0x0.0x5.90 in) Also available in 6 Ω, data upon request Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. HF - Two hours THIELE & SMALL PARAMET 89 5. Ω Qes 0. Qms 7.5 Qts 0.8 Vas 5 dm (0.8 ft ) Sd cm (0.5 in ) η 0 0.8 % ± 5 mm ± 5.5 mm 6 g 0.9 T m 0.8 mh HF test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. RCK06HCX5-8 MMD0-8 defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 86

COAX IALS 8CXN5 COAXIAL 500 W 97 db 00 nominal coverage 70-8000 Single Neodymium magnet assembly Nom. Diameter 0 mm (8 in) Nom. Impedance 6 Ω (), 7. Ω (HF) 70-8000 Dispersion Angle 00 Neodymium Ring Waterproof cone treatment Front side UNIT Sensitivity (W/m) 97 db Nom. (AES) 50 W Continuous Program 500 W 5 mm ( in) Aluminuim.5 T Winding 7.0 mm (0.67 in) Magnetic Gap 8.0 mm (0. in) HF UNIT Sensitivity (W/m) 0 db Nom. (AES) 50 W Continuous Program 00 W mm (.7 in) Diaphragm Material Polyimide commended Crossover 5.8 k.8 T Inductance 0. mh 5 mm (8.8 in) 0 mm (8. in) Baffle Cutout Diameter 87 mm (7. in) mm (. in) Flange and Gasket Thickness 0 mm (0. in).5 kg (5.5 lb). kg (6.8 lb) 95xx75 mm (.6x.6x6.89 in) Also available in and 6 Ω, data upon request Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. THIELE & SMALL PARAMET 68.9 Ω Qes 0.9 Qms.7 Qts 0.7 Vas 7 dm (0.60 ft ) Sd 0 cm (. in ) η 0.8 % ± 6 mm ± 6 mm g.6 T m 0.9 mh HF HF - Two hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. RCK008HCX5-8 MMD00-8 defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 87

COAX IALS CXN76 COAXIAL 700 W 99 db 80 nominal coverage 5-8000 Single Neodymium magnet assembly Nom. Diameter 0 mm ( in) Nom. Impedance 6.5 Ω (), (HF) 5-8000 Dispersion Angle 80 Neodymium Ring Waterproof cone treatment Front side UNIT Sensitivity (W/m) 99 db Nom. (AES) 50 W Continuous Program 700 W 76 mm ( in) Copper.5 T Winding 6. mm (0.6 in) Magnetic Gap 8.0 mm (0. in) HF UNIT Sensitivity (W/m) 05 db Nom. (AES) 80 W Continuous Program 60 W Diaphragm Material commended Crossover 5 Inductance 75 mm ( in) Polyester/Titanium. k.9 T 0. mh 5 mm (. in) 98 mm (.7 in) Baffle Cutout Diameter 8 mm (. in) 70 mm (6.7 in) Flange and Gasket Thickness mm (0.55 in) 5 kg ( lb) 6. kg (.89 lb) 5x5x mm (6.7x6.7x8.8 in) Also available in Ω, data upon request Also available 5HCX76 (with 60 x 0 horn) Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. HF - Two hours THIELE & SMALL PARAMET 5.0 Ω Qes 0. Qms 8.0 Qts 0.9 Vas 0 dm (. ft ) Sd 5 cm (80.9 in ) η 0. % ± mm ± 6 mm 7 g 7.6 T m 0.8 mh 0 HF test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. RCKCXN76-8 MMD90-8 defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 88

COAX IALS CXN88 COAXIAL Preliminary data 000 W 99 db 60 nominal coverage 55-8000 Single Neodymium magnet assembly demodulating ring for very low distortion Double silicone spider with optimized compliance Nom. Diameter 0 mm ( in) Nom. Impedance 6.6 Ω (), 8.5 Ω (HF) 55-8000 Dispersion Angle 60 Neodymium Ring Waterproof cone treatment Front side UNIT Sensitivity (W/m) 99 db Nom. (AES) 500 W Continuous Program 000 W 88 mm (.5 in) Aluminuim.0 T Winding.5 mm (0.85 in) Magnetic Gap 0.0 mm (0.9 in) HF UNIT Sensitivity (W/m) 05 db Nom. (AES) 80 W Continuous Program 60 W 75 mm (.0 in) Diaphragm Material Titanium commended Crossover 5. k.75 T Inductance 0. mh 5 mm (. in) 98 mm (.7 in) Baffle Cutout Diameter 8 mm (. in) 75 mm (6.89 in) Flange and Gasket Thickness mm (0.5 in) 6.0 kg (. lb) 7. kg (6.09 lb) 5x5x mm (6.7x6.7x8.8 in) Also available in and 6 Ω, data upon request Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. THIELE & SMALL PARAMET 55 5. Ω Qes 0.8 Qms 5.6 Qts 0.7 Vas 0 dm (. ft ) Sd 5 cm (80.9 in ) η 0. % ± 8.5 mm ± 9.0 mm 6 g. T m.05 mh 96 HF HF - Two hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. RCKCXN88-8 MMDDTN-8M defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 89

COAX IALS CXN76 COAXIAL 800 W 00 db 80 nominal coverage 5-8000 Single Neodymium magnet assembly Nom. Diameter 55 mm ( in) Nom. Impedance 6.5 Ω (), 8. Ω (HF) 5-8000 Dispersion Angle 80 Neodymium Ring Waterproof cone treatment Front Side UNIT Sensitivity (W/m) 00 db Nom. (AES) 00 W Continuous Program 800 W 76 mm ( in) Copper.5 T Winding 7.0 mm (0.67 in) Magnetic Gap 8.0 mm (0. in) HF UNIT Sensitivity (W/m) 05 db Nom. (AES) 5 80 W Continuous Program 6 60 W Diaphragm Material commended Crossover 7 Inductance Included by 6 db down points. Applied RMS Voltage is set to.8v - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. HF - Two hours test made with continuous pink noise signal (6 db crest factor) within the 75 mm ( in) Polyester/Titanium. k.8 T 0. mh 59 mm (. in) mm (.5 in) Baffle Cutout Diameter mm (.7 in) 88 mm (7. in) Flange and Gasket Thickness 5 mm (0.59 in) 5.6 kg (.5 lb) 7. kg (5.87 lb) 500x95x75 mm (9.68x9.8x0.8 in) Also available HCX76 (with 60 x 0 horn) THIELE & SMALL PARAMET 5 5. Ω Qes 0.9 Qms 8.5 Qts 0.8 Vas dm (.6 ft ) Sd 707 cm (09.59 in ) η 0.0 % ± 6 mm ± 8 mm 67 g 8. T m.0 mh 55 HF range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. Applied RMS Voltage is set to.8v 5 hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended RCKCXN76-8 MMD90-8M crossover frequency to 0 k. 6 defined as db greater than the 7 db/oct. or higher slope high-pass filter. bcspeakers.com 90

COAX IALS 5HCX76 COAXIAL 800 W 99 db 60 x 0 nominal coverage 0-8000 Modified exponential horn flare for improved acoustic loading and controlled coverage Single Neodymium magnet assembly Nom. Diameter Nom. Impedance Dispersion Angle Waterproof cone treatment UNIT Sensitivity (W/m) Nom. (AES) Continuous Program Winding Magnetic Gap HF UNIT Sensitivity (W/m) Nom. (AES) Continuous Program 80 mm (5 in) 6.0 Ω (lf), 8.0 Ω (hf) 0-8000 60 x0 Neodymium Ring Front side 99 db 00 W 800 W 76 mm ( in) Copper.5 T 6.5 mm (0.65 in) 8.0 mm (0. in) 07 db 80 W 60 W Diaphragm Material commended Crossover 5 Inductance 75 mm ( in) Titanium. k.9 T 0. mh 9 mm (5.5 in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) 00 mm (7.87 in) Flange and Gasket Thickness 6 mm (0.6 in) 5.6 kg (.5 lb) 7. kg (5.87 lb) 500x95x75 mm (9.68x9.8x0.8 in) Also available 5CXN76 (without horn / 80 disp) Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. HF - Two hours THIELE & SMALL PARAMET 8 5. Ω Qes 0. Qms 5.8 Qts 0.8 Vas 6 dm (8.6 ft ) Sd 855 cm (.5 in ) η 0.7% ±.5 mm ± 6 mm 8 g 7.8 T m 0.9 mh 6 HF test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. RCK5HCX76-8 MMDBTN-8 defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 9

COAX IALS 5CXN88 COAXIAL Preliminary data 000 W 99 db 80 nominal coverage 5-8000 Single Neodymium magnet assembly demodulating ring for very low distortion Double silicone spider with optimized compliance Nom. Diameter 80 mm (5 in) Nom. Impedance 5. (), 8.5 Ω (HF) 5-8000 Dispersion Angle 80 Neodymium Ring Waterproof cone treatment Front side UNIT Sensitivity (W/m) 99 db Nom. (AES) 500 W Continuous Program 000 W 88 mm (.5 in) Aluminuim. T Winding.0 mm (0.87 in) Magnetic Gap.0 mm (0. in) HF UNIT Sensitivity (W/m) 05 db Nom. (AES) 80 W Continuous Program 60 W 75 mm (.0 in) Diaphragm Material Titanium commended Crossover 5. k.75 T Inductance 0. mh 9 mm (5. in) 7 mm (.7 in) Baffle Cutout Diameter 5 mm (.9 in) mm (. in) Flange and Gasket Thickness 8 mm (8.58 in) 5.6 kg (.5 lb) 7. kg (5.87 lb) 500x95x75 mm (9.68x9.8x0.8 in) Also available in and 6 Ω, data upon request Included by 6 db down points. Applied RMS Voltage is set to.8v. - Two hour test made with continuous pink noise signal (6 db crest factor) within the range -0. Loudspeaker in free air. THIELE & SMALL PARAMET 6.5 Ω Qes 0.9 Qms 8. Qts 0.8 Vas 7 dm (.8 ft ) Sd 855 cm (.5 in ) η 0. % ± 8 mm ± 9.5 mm 9 g 0. T m.0 mh 58 HF HF - Two hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. and HF Power calculated on rated minimum impedance. RCK5CXN88-8 MMDDTN-8M defined as db greater than the 5 db/oct. or higher slope high-pass filter. bcspeakers.com 9

FE HF B&C Speakers has been a market leader in compression driver technology for decades. Our reliability and performance is second to none. We continue to work with a wide variety of materials to further improve the performance of our HF devices. Through our modeling programs we are able to analyze every aspect of the driver, and study the impact of key components on each design. levels, and creates a smooth top end. HT Polyester provides superior power handling and higher output levels in the upper octave ranges. Standard features in our compression drivers include copper shorting rings, FEA optimized phase plugs and edgewound, copper-clad, aluminium voice coil (CCAW) wire. We use four different diaphragm materials: Mylar, pure Titanium, Polyimide, and High Temperature (HT) Polyester. Each material has its own unique benefits and qualities. Mylar allows for an exceptionally smooth transient. Pure Titanium provides superb power handling and excellent reliability in the field. Polyimide achieves very high power handling and bcspeakers.com 9

FE HF DE0 FE HF ER 0 W 07 db 5 mm ( in) aluminium voice coil 500-8000 " horn throat diameter Polyester diaphragm Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 5 mm ( in) 6. Ω 0 W 0 W 07 db commended crossover 5 Inductance Diaphragm Material.5-8 k.5 k 5 mm ( in) CCAW () 0. mh Polyester.55 T Ferrite Ring Two M5 holes 80 on 76 mm ( in) diameter 90 mm (.5 in) 5 mm (. in) ( unit) 0.8 kg (.8 lb) (8 units) 7.05 kg (5.5 lb) (8 units) 5x5x65 mm (9.5x9.5x6.5 in) placement Diaphragm MMD00-8 Also available in 6 Ω, data upon request Driver mounted on B&C ME 0 horn. hour test made with continuous pink noise signal (6 db crest factor) within the specified range. Power calculated on rated minimum impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 9

FE HF DE FE HF ER 50 W 06 db 6 mm (. in) aluminium voice coil 500-8000 " horn throat diameter Polyester diaphragm Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 5 mm ( in) 7. 5 W 50 W 06 db commended crossover 5 Inductance Diaphragm Material.5-8 k. k 6 mm (. in) CCAW () 0. mh Polyester.5 T Ferrite Ring Two M5 holes 80 on 76 mm ( in) diameter 90 mm (.5 in) 9 mm ( in) ( unit) kg (. lb) (8 units) 8.9 kg (0 lb) (8 units) 5x5x65 mm (9.5x9.5x6.5 in) placement Diaphragm MMD0-8 Also available in 6 Ω, data upon request Also available DETC (Titanium diaphragm) Driver mounted on B&C ME 5 horn. hour test made with continuous within the specified range. Power calculated on rated minimum impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 95

FE HF DETN FE HF ER 60 W 05 db 6 mm (. in) aluminium voice coil 500-8000 " horn throat diameter Titanium diaphragm Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 5 mm ( in) 7. Ω 0 W 60 W 05 db commended crossover 5 Inductance Diaphragm Material.5-8 k. k 6 mm (. in) CCAW () 0. mh Titanium.5 T Ferrite Ring Two M5 holes 80 on 76 mm ( in) diameter Three M6 holes 0 on 57 mm (. in) diameter 90 mm (.5 in) 9 mm ( in) ( unit). kg (. lb) (8 units) 9. kg (0.7 lb) (8 units) 5x5x65 mm (9.5x9.5x6.5 in) placement Diaphragm MMD0TN-8 Also available in 6 Ω, data upon request Also available DE (Polyester diaphragm) Driver mounted on B&C ME 5 horn. hour test made with continuous pink noise signal (6 db crest factor) within the specified range. Power calculated on rated minimum impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 96

FE HF DE60 FE HF ER 80 W 07 db mm (.7 in) aluminium voice coil 500-8000 " horn throat diameter Polyester diaphragm Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 5 mm ( in) 7. Ω 0 W 80 W 07 db commended crossover 5 Inductance Diaphragm Material.5-8 k k mm (.7 in) CCAW () 0. mh Polyester.5 T Ferrite Ring Two M6 holes 80 on 76 mm ( in) diameter 0 mm ( in) 6 mm (. in) ( unit).6 kg (.5 lb) (8 units).9 kg (0.6 lb) (8 units) 5x5x65 mm (9.5x9.5x6.5 in) placement Diaphragm MMDDE60-8 Also available in 6 Ω, data upon request Also available DE00 (Titanium Diaphragm) Driver mounted on B&C ME 5 horn. hour test made with continuous within the specified range. Power calculated on rated minimum impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 97

FE HF DE80 FE HF ER 0 W 06.5 db mm (.7 in) aluminium voice coil 000-7000 " horn throat diameter Polyimide diaphragm Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 5 mm ( in) 7. Ω 60 W 0 W 06.5 db commended crossover 5 Inductance Diaphragm Material - 7 k k mm (.7 in) CCAW () 0. mh Polyimide.5 T Ferrite Ring Two M6 holes 80 on 76 mm ( in) diameter 0 mm (.0 in) 6 mm (. in) ( unit).6 kg (.5 lb) (8 units).9 kg (0.6 lb) (8 units) 5x5x65 mm (9.5x9.5x6.5 in) placement Diaphragm MMDDE80-8 Also available in 6 Ω, data upon request Also available DE 00 (Titanium Diaphragm) Driver mounted on B&C ME 5 horn. Hours test made with continuous pink noise signal (6 db crest factor) within the specified range. Power calculated on rated minimum impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms Nominal Impedance. Average SPL from 500 to 8000. 5 db/oct. or higher slope high-pass filter. Also available in the Polyester version: DE60 bcspeakers.com 98

FE HF DE50 FE HF ER 0 W 08.5 db mm (.7 in) aluminium voice coil 000-8000 " horn throat diameter Polyimide diaphragm Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 5 mm ( in) 7. 60 W 0 W 08.5 db commended crossover 5 Inductance Diaphragm Material - 8 k.6 k mm (.7 in) CCAW () 0. mh Polyimide.85 T Ferrite Ring Two M6 holes 80 on 76 mm ( in) diameter Three M6 holes 0 on 57 mm (. in) diameter 0 mm (.7 in) 6 mm (. in) ( unit). kg (.6 lb) ( units) 8.75 Kg (9. lb) ( units) 65x5x70 mm (0.x5.x6.69 in) placement Diaphragm MMDDE50-8 Also available in 6 Ω, data upon request Also available DE50TN (Titanium Diaphragm) Driver mounted on B&C ME 5 horn. hour test made with continuous within the specified range. Power calculated on rated minimum impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. Average SPL from 600 to 6000. 5 db/oct. or higher slope highpass filter. bcspeakers.com 99

FE HF DE68TN FE HF ER 60 W 08 db 65 mm (.5 in) aluminium voice coil 000-8000 Titanium diaphragm Ferrite magnet assembly with shorting copper cap. horn throat diameter Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 6 mm (. in) 7. Ω 80 W 60 W 08 db commended crossover 5 Inductance Diaphragm Material - 8 k. k 65 mm (.5 in) CCAW () 0.5 mh Titanium.75 T Ferrite Ring Two M6 holes 90 on 0 mm ( in) diameter 56 mm (6. in) 66 mm (.6 in) ( unit).8 kg (8.8 lb) ( units) 8.5 kg (8.9 lb) ( units) 0x0x90 mm (8.7x8.7x7.8 in) placement Diaphragm MMD68TN-8 Also available in 6 Ω, data upon request Driver mounted on B&C ME 90 horn. hour test made with continuous within the specified range. Power calculated on rated minimum impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 00

FE HF DE60TN FE HF ER 0 W 07 db 75 mm ( in) aluminium voice coil 000-8000." horn throat diameter Shorting coppercap for extended HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 6 mm (. in) 8.6 Ω 0 W 0 W 07 db commended crossover 5 Inductance Diaphragm Material - 8 k. k 75 mm ( in) CCAW () 0. mh Titanium.6 T Ferrite Ring Four M6 holes 90 on 0 mm ( in) diameter 56 mm (6. in) 66 mm (.6 in) ( unit). kg (9 lb) ( units) 8.8 kg (9. lb) ( units) 0x0x90 mm (8.7x8.7x7.8 in) placement Diaphragm MMDBTN-8M Also available in 6 Ω, data upon request Driver mounted on B&C ME 90 horn. hour test made with continuous within the range from the recommended crossover frequency to 0 k. impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 0

FE HF DE8TN FE HF ER 0 W 06.5 db 75 mm ( in) aluminium voice coil 500-8000." horn throat diameter Titanium diaphragm Shorting copper cap for extended HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 6 mm (. in) 8.5 Ω 0 W 0 W 06.5 db commended crossover 5 Inductance Diaphragm Material 0.5-8 k.0 k 75 mm ( in) CCAW () 0. mh Titanium.8 T Ferrite Ring Four M6 holes 90 on 0 mm ( in) diameter 70 mm (6.7 in) 6 mm (.5 in) ( unit).5 kg (9.9 lb) ( units) 9.6 kg (. lb) ( units) 0x0x90 mm (8.7x8.7x7.8 in) placement Diaphragm MMDATN-8 Also available in 6 Ω, data upon request Also available DE85 (Polyester/Titanium Diaphragm) Driver mounted on B&C ME 90 horn. hour test made with continuous pink noise signal (6 db crest factor) within the range from the recommended crossover frequency to 0 k. Power calculated on rated minimum impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 0

FE HF DE90TN FE HF ER 0 W 07.5 db 75 mm ( in) aluminium voice coil 500-8000." horn throat diameter Titanium diaphragm Shorting copper cap for extended HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 6 mm (. in) 8. Ω 0 W 0 W 07.5 db commended crossover 5 Inductance Diaphragm Material 0.5-8 k k 75 mm ( in) CCAW () 0. mh Titanium.8 T Ferrite Ring Four M6 holes 90 on 0 mm ( in) diameter 70 mm (6.7 in) 65 mm (.5 in) ( unit).5 kg (9.9 lb) ( units) 9.6 kg (. lb) ( units) 0x0x90 mm (8.7x8.7x7.8 in) placement Diaphragm MMDDTN-8M Also available in 6 Ω, data upon request Also available DE95TN (with 50 mm/.0 in exit) Driver mounted on B&C ME 90 horn. hour test made with continuous within the specified range. Power calculated on rated minimum impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 0

FE HF DE85TN FE HF ER 0 W 07 db 75 mm ( in) aluminium voice coil 500-8000 " horn throat diameter Titanium diaphragm Shorting copper cap for extended HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 50 mm ( in) 8. Ω 0 W 0 W 07 db commended crossover 5 Inductance Diaphragm Material - 8 k k 75 mm (.0 in) CCAW () 0.05 mh Titanium.8 T Ferrite Two M6 holes 90 on 0 mm ( in) diameter 70 mm (6.7 in) 6 mm (.5 in) ( unit).5 kg (9.9 lb) ( units) 9.6 kg (. lb) ( units) 0x0x90 mm (8.7x8.7x7.8 in) placement Diaphragm MMDATN-8 Also available in 6 Ω, data upon request Also available DE85 (Polyester/Titanium Diaphragm) Driver mounted on B&C ME 75 horn. hour test made with continuous within the specified range. Power calculated on rated minimum impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 0

FE HF DE750TN FE HF ER 0 W 07.5 db 75 mm ( in) aluminium voice coil 500-8000 " horn throat diameter Titanium diaphragm Shorting copper cap for extended HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 50 mm ( in) 7. 0 W 0 W 07.5 db commended crossover 5 Inductance Diaphragm Material 0.5-8 k 0.8 k 75 mm ( in) CCAW () 0. mh Titanium.9 T Ferrite Ring Four M6 holes 90 on 0 mm ( in) diameter 80 mm (7. in) 87 mm (. in) 6. kg (.9 lb) 6.5 kg (. lb) 90x90x0 mm (7.8x7.8x.7 in) placement Diaphragm MMDATN-8 Also available in 6 Ω, data upon request Driver mounted on B&C ME75 horn. hour test made with continuous within the specified range. Power calculated on rated minimum impedance. defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. Average SPL from 500 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 05

B&C Speakers has been a leader in compression driver technology for decades, and is now a market leader in the development of neodymium compression drivers for the professional audio market. We are constantly advancing the science of high frequency driver development and adding new products to our range. The use of Neodymium magnets in our high frequency drivers has not only allowed us to dramatically reduce the size and weight, but also to improve performance and overall value. Our reliability and performance is second to none. We continue to work with a variety of materials to further improve performance. Through our modeling programs we are able to analyze every aspect of the driver, and study the impact of key components on each design. We use four different diaphragm materials: Mylar, pure Titanium, Polyimide and High Temperature (HT) Polyester. Each material has its own unique benefits and qualities. Mylar allows for an exceptionally smooth transient. Pure Titanium provides superb power handling and excellent reliability in the field. Polyimide achieves very high power handling and levels, and creates a smooth top end. HT Polyester provides superior power handling and higher output levels in the upper octave ranges. The updated range of bent voice-coil former high frequency drivers are particularly noteworthy. The DE680TN, DE880TN, DE980TN, DE990TN and DE090TN high frequency drivers feature a robust titanium diaphragm that incorporates next generation surround geometry, together with a brand new, optimized phase plug. Significant research has yielded a new coil former that solidifies the diaphragm with negligible increase in mass. The result is improved high frequency linearity and reduced distortion. They represent an excellent solution for two-way point source enclosures, as well as for mounting a waveguide horn in multi-driver line array systems. HF bcspeakers.com 06

HF DE5 TWEETER 50 W 08 db 500-8000 Neodymium magnet assembly Nominal (AES) Continuous Program Sensitivity (W/m) 7 Ω 5 W 50 W 08 db.5-8 k commended crossover 5 k mm (.5 in) CCAW () Inductance 0. mh Diaphragm Material Polyester. T Neodymium Inside Slug Three M holes 0 on 9 mm (.6 in) diameter 00 mm ( in) 6 mm (.8 in) ( unit) 0.7 kg (.5 lb) (8 units) 6. kg (. lb) (8 units) 5x5x65 mm (9.5x9.5x6.5 in) placement Diaphragm MMD05-8 within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. db/oct. or higher slope high-pass filter. bcspeakers.com 07

HF DE7 HF ER 0 W 09 db 5 mm ( in) aluminium voice coil 000-8000 /" horn throat diameter Polyester diaphragm Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 9 mm (0.75 in) 6.6 Ω 0 W 0 W 09 db commended Crossover 5 Inductance Diaphragm material - 8 k.5 k 5 mm ( in) CCAW () 0. mh Polyester.65 T Neodymium Ring Two M holes 80 on 5 mm (. in) diameter 6 mm (. in) 5 mm (. in) 0.7 kg (0.7 lb) (8 units).5 kg (. lb) (8 units) 0x0x90 mm (5.x.x.5 in) placement Diaphragm MMDDE5-8 Also available in 6 Ω, data upon request Also available DE5 with 5 mm (0.5 in) exit Driver mounted on B&C ME7 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8v for 8 ohms. Average SPL from 000 to 6000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 08

HF DE0 HF ER 50 W 06 db 6 mm (. in) aluminium voice coil 000-8000 Ultra Compact 60 mm diameter HT Polymer diaphragm " horn throat diameter Throat diameter Nominal (AES) Continuous Program Sensitivity (W/m) 5 mm (.0 in) 5 W 50 W 06 db commended crossover 5 Inductance Diaphragm Material - 8 k k 6 mm (. in) CCAW () 0. mh HT Polymer.8 T Neodymium Ring Two M5 holes 80 on 5 mm (.05 in) diameter 60 mm (.6 in) 5 mm (.8 in) ( unit) 0. kg (0.7 lb) (8 units) kg (8.8 lb) (8 units) 5x5x65 mm (9.5x9.5x6.5 in) placement Diaphragm MMDDE08-8 Also available in 6 Ω, data upon request Driver mounted on B&C ME 5 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 09

DE00TN HF ER 00 W 06 db mm (.7 in) aluminium voice coil 00-8000 Titanium diaphragm Compact Neodymium magnet assembly with shorting copper cap for extended HF " horn throat diameter HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 5 mm ( in) 7.7 Ω 50 W 00 W 06 db commended crossover 5 Inductance Diaphragm Material. - 8 k.5 k mm (.7 in) CCAW () 0. mh Titanium.8 T Neodymium Ring Two M6 holes 80 on 76 mm ( in) diameter 85 mm (.in) mm (.7 in) ( unit) 0.8 kg (.8 lb) (8 units) 6.7 kg (.7 lb) (8 units) 5x5x65 mm (9.5x9.5x6.5 in) placement Diaphragm MMD00TN-8 Also available in 6 Ω, data upon request Also available DE00 (Polyimide Diaphragm) Driver mounted on B&C ME5 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 0

HF DE50 HF ER 00 W 07 db mm (.7 in) aluminium voice coil 000-8000 Titanium diaphragm Shorting copper cap for extended HF Optimized Neodymium magnet assembly " horn throat diameter Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 5 mm ( in) 7.6 Ω 50 W 00 W 07 db commended crossover 5 Inductance Diaphragm Material - 8 k.5 k mm (.7 in) CCAW () 0. mh Titanium.9 T Neodymium Ring Two M6 holes 80 on 76 mm ( in) diameter Three M6 holes 0 on 57 mm (. in) diameter 0 mm ( in) 5 mm ( in) ( unit). kg (. lb) (8 units).85 kg (6. lb) (8 units) 5x5x65 mm (9.5x9.5x6.5 in) placement Diaphragm MMD50-8 Also available in 6 Ω, data upon request Driver mounted on B&C ME 5 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com

DE550TN HF ER 0 W 08 db 5 mm ( in) aluminium voice coil 000-7000 HT Polymer diaphragm " horn throat diameter HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 5 mm ( in) 8. Ω 70 W 0 W 08 db commended crossover 5 Inductance Diaphragm Material - 7 k. k 5 mm (.0 in) CCAW () 0. mh Titanium.0 T Neodymium Ring Two M6 holes 80 on 76 mm ( in) diameter 9 mm (.6 in) 9 mm (.9 in) ( unit).5 kg (.76 lb) (8 units) 0.65 kg (.8 lb) (8 units) 0x0x50 mm (8.7x8.7x5.9 in) placement Diaphragm MMD550TN-8 Also available in 6 Ω, data upon request Also available DE550 (HT Polymer Diaphragm) Driver mounted on B&C ME5 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 db/oct. or higher slope high-pass filter. bcspeakers.com

DE680TN HF ER 60 W 08 db 65 mm (.5 in) CCAW voice coil 000-8000 Neodymium magnet assembly with shorting copper cap Titanium diaphragm." horn throat diameter HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 6 mm (. in) 7.7 Ω 80 W 60 W 08 db commended crossover 5 Inductance Diaphragm Material - 8 k. k 65 mm (.5 in) CCAW () 0.5 mh Titanium.8 T Neodymium Ring Four M6 holes 90 on 0 mm ( in) diameter 5 mm (.5 in) 5 mm (.0 in) ( unit).75 kg (.85 lb) ( units) 7.5 kg (6. lb) ( units) 65x5x70 mm (0.x5.x6.69 in) placement Diaphragm MMD680TN-8 Also available in 6 Ω, data upon request Driver mounted on B&C ME 90 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com

DE880TN HF ER 0 W 08 db 75 mm ( in) aluminium voice coil 500-8000 Neodymium magnet assembly with shorting copper cap Titanium diaphragm." horn throat diameter HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 6 mm (. in) 8. Ω 0 W 0 W 08 db commended crossover 5 Inductance Diaphragm Material 0.5-8 k. k 75 mm ( in) CCAW () 0. mh Titanium.85 T Neodymium Ring Four M6 holes 90 on 0 mm ( in) diameter mm (.9 in) 5. mm (. in) ( unit). kg (5. lb) ( units) 9.8 kg (.6 lb) ( units) 95x60x80 mm (.6x6.0x7.09 in) placement Diaphragm MMDDTN-8M Also available in 6 Ω, data upon request Driver mounted on B&C ME 90 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com

DE980TN HF ER 0 W 08.5 db 75 mm ( in) aluminium voice coil 500-8000 Neodymium magnet assembly with shorting copper cap Titanium diaphragm." horn throat diameter HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 6 mm (. in) 8. Ω 0 W 0 W 08.5 db commended crossover 5 Inductance Diaphragm Material 0.5-8 k. k 75 mm (.0 in) CCAW () 0. mh Titanium.05 T Neodymium Ring Four M6 holes 90 on 0 mm ( in) diameter mm (.9 in) 5.5 mm (. in) ( unit). kg (5. lb) ( units) 9.8 kg (.6 lb) ( units) 95x60x80 mm (.6x6.0x7.09 in) placement Diaphragm MMDDTN-8M Also available in 6 Ω, data upon request Also available DE985TN (" exit) Driver mounted on B&C ME 90 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 5

DE990TN HF ER 00 W 07.5 db 86 mm (. in) aluminium voice coil 500-8000 Neodymium magnet assembly with shorting copper cap." horn throat diameter HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 6 mm (. in) 7.6 Ω 00 W 00 W 07.5 db commended crossover 5 Inductance Diaphragm Material 500-8 k.0 k 86 mm (. in) CCAW () 0. mh Titanium.9 T Neo Inside Ring Four M6 holes 90 on 0 mm ( in) diameter 8 mm (.65 in) 6 mm (.8 in) ( unit).85 kg (.08 lb) ( units) 8.0 kg (7.6 lb) ( units) 65x5x70 mm (0.x5.x6.69 in) placement Diaphragm MMD5ETN-8M Also available in 6 Ω, data upon request Driver mounted on B&C ME90 horn within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 6

DE885TN HF ER 0 W 08.5 db 75 mm ( in) aluminium voice coil 800-8000 Neodymium magnet assembly with shorting copper cap Titanium diaphragm " horn throat diameter HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 50 mm (.0 in) 0 W 0 W 08.5 db commended crossover 5 Inductance Diaphragm Material 0.8-8 k.0 k 75 mm ( in) CCAW () 0. mh Titanium.85 T Neodymium Ring Four M6 holes 90 on 0 mm ( in) diameter mm (.88 in) 89 mm (.5 in) ( unit).9 kg (5.9 lb) ( units) 0. kg (.9 lb) ( units) 0x65x0 mm (.0x6.5x9.05 in) placement Diaphragm MMDDTN-8M Also available in 6 Ω, data upon request Driver mounted on B&C ME60 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 7

DE90TN HF ER 0 W 08.5 db 75 mm ( in) aluminium voice coil 500-8000 Neodymium magnet assembly with shorting copper cap Titanium diaphragm." horn throat diameter HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) mm (. in) 7. 0 W 0 W 08.5 db commended Crossover 5 Inductance Diaphragm material 0.5-0 k. k 75 mm (.0 in) CCAW () 0. mh Titanium.05 T Neodymium Ring Two M holes 90 on 0 mm ( in) diameter mm (5. in) 5 mm (.05 in). kg (5.9 lb) ( units) 0. Kg (.9 lb) ( units) 95x60x80 mm (.6x6.0x7.09 in) placement Diaphragm MMDBTN-8M Also available in 6 Ω, data upon request Driver mounted on B&C ME90 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8v for 8 ohms. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 8

DE080TN HF ER 80 W 09 db 00 mm ( in) aluminium voice coil 500-0000 Neodymium magnet assembly with shorting copper cap Titanium diaphragm.5" horn throat diameter HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 8 mm (.5 in) 8. Ω 0 W 80 W 09 db commended crossover 5 Inductance Diaphragm Material 0.5-0 k k 00 mm ( in) CCAW () 0.8 mh Titanium.95 T Neodymium Ring Four M6 holes 90 on 0 mm ( in) diameter 5 mm (6. in) 60 mm (. in). kg (7.5 lb).7 kg (8. lb) 90x90x00 mm (7.8x7.8x.9 in) placement Diaphragm MMDBTN-8M Also available in 6 Ω, data upon request Also available DE085TN (" exit) Driver mounted on B&C ME90 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 9

DE090TN HF ER 0 W 08 db 00 mm ( in) aluminium voice coil 500-0000 Neodymium magnet assembly with shorting copper cap Titanium diaphragm." horn throat diameter HF Throat Diameter Nominal (AES) Continuous Program Sensitivity (W/m) 6 mm (. in) 8. Ω 0 W 0 W 08.0 db commended crossover 5 Inductance Diaphragm Material 0.5-0 k 0.8 k 00 mm ( in) CCAW () 0.8 mh Titanium.9 T Neo Inside Ring Four M6 holes 90 on 0 mm ( in) diameter 7 mm (5.0 in) 5 mm (5.0 in) ( unit).9 kg (.9 lb) ( units) 8. kg (8.08 lb) ( units) 95x60x80 mm (.6x6.0x7.09 in) placement Diaphragm MMDCTN-8M Also available in 6 Ω, data upon request Driver mounted on B&C ME60 horn. within the range -0. Power calculated on rated minimum defined as db greater than the Applied RMS Voltage is set to.8 V for 8 ohms. 5 db/oct. or higher slope high-pass filter. bcspeakers.com 0

LINE ARR A Y S O U RCES Over the last decades, there has been a dramatic shift towards line arrays in the professional arena. This has emphasized the importance of a superior high frequency horn and driver combinations. B&C s high frequency drivers have long been considered the industry standard, but line array systems require controlled coverage patterns. We have researched many aspects of line array waveguides, and are proud to offer our customers a complete series of high frequency solutions for line array systems. acoustic lenses create a well-behaved phasecoherent wavefront up to 5 k, and offer a very high Active Radiating Factor. Our engineering team has performed all of the critical tests to ensure that each aspect of line array performance has been carefully considered. The WGX and WG series are available as a complete assembly, combined with a wide variety of our and. exit high frequency drivers. The WGX and WG series are based on our state of the art neodymium compression drivers coupled to a proprietary waveguide. These specially designed bcspeakers.com

WG00 LINE ARRAY SOURCE 00 W 08.5 db mm (.7 in) aluminium voice coil 00-8000 Line Array optimized Waveguide with DE00 driver Polyimide diaphragm Compact Neodymium magnet assembly 0 max horizontal coverage LINE ARR A Y S O U RCES Horizontal Coverage 0 max Active Radiating Factor 9.5 % commended Crossover.5 k Waveguide Material Cast 7.7 Ω Nominal (AES) 50 W Continuous Program 00 W Sensitivity (W/m) 08.5 db 5. - 8 k mm (.7 in) Inductance 0.8 mh Diaphragm Material Polyimide.8 T Neodymium Ring MOUNTING A SHIPPING INFORMATION Waveguide Baffle Cutout 0x5 mm (x in) Driver diameter 86 mm (. in) Dimensions x87x55 mm (.x.5x6. in). kg (.9 lb).5 kg (.0 lb) 0x95x80 mm (.7x.7x7. in) HORIZONTAL ANGLE frequency VERTICAL ANGLE frequency 5 0 80 50 0 90 60 0 0 0 60 90 0 50 80 6 5 0 db/oct. or higher slope high-pass filter. Driver mounted on B&C ME 90 horn. within the range from the recommended crossover frequency to 0 k. impedance. defined as db greater than the 6 80 50 0 90 60 0 0 0 60 90 0 50 80 Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 Waveguide mounted on 90 x 0 bell horn. bcspeakers.com

WGX880TN LINE ARRAY SOURCE 0 W 08 db 75 mm ( in) aluminium voice coil 500-7000 Line Array optimized Waveguide with DE880TN driver Titanium diaphragm Neodymium magnet assembly with shorting copper cap 0 max horizontal coverage LINE ARR A Y S O U RCES Horizontal Coverage 0 max Active Radiating Factor 9.7 % commended Crossover 0.8 k Waveguide Material Cast 8. Ω Nominal (AES) 0 W Continuous Program 0 W Sensitivity (W/m) 08 db 5 0.5-7 k 75 mm ( in) CCAW Diaphragm Material Titanium.85 T Neodymium Ring MOUNTING A SHIPPING INFORMATION Waveguide Baffle Cutout 5x5 mm (6x in) Driver diameter mm (.9 in) Dimensions 6x0x5 mm (6.x5.x9. in). kg (6.8 lb). kg (7.05 lb) 5x0x75 mm (9.6x5.5x6.9 in) HORIZONTAL ANGLE 5 0 VERTICAL ANGLE frequency 80 50 0 90 60 0 0 0 60 90 0 50 80 6 5 0 db/oct. Or higher slope high-pass filter. within the range from the recommended crossover frequency to 0 k. impedance. defined as db greater then the frequency 6 80 50 0 90 60 0 0 0 60 90 0 50 80 Applied RMS Voltage is set to.8 V for 8 ohms. 5 Waveguide mounted on 90 x 0 bell horn. bcspeakers.com

WGX090TN LINE ARRAY SOURCE 0 W 08 db 00 mm ( in) aluminium voice coil 500-8000 Line Array optimized Waveguide with DE090TN driver Titanium diaphragm Neodymium magnet assembly with shorting copper cap 0 max horizontal coverage LINE ARR A Y S O U RCES Horizontal Coverage 0 max Active Radiating Factor 9.7 % commended Crossover 0.8 k Waveguide Material Cast Nominal (AES) 0 W Continuous Program 0 W Sensitivity (W/m) 08 db 5 500-8 k 00 mm (.0 in) CCAW Inductance 0.8 mh Diaphragm Material Titanium.9 T Neo Inside Ring MOUNTING A SHIPPING INFORMATION Waveguide Baffle Cutout 5x5 mm (6x in) Driver diameter 7 mm (5.0 in) Dimensions 6x0x mm (6.x5.x9. in).9 kg (6.9 lb) kg (6.6 lb) 5x0x75 mm (9.6x5.5x6.9 in) HORIZONTAL ANGLE frequency VERTICAL ANGLE frequency 5 0 80 50 0 90 60 0 0 0 60 90 0 50 80 6 5 0 db/oct. or higher slope high-pass filter. Driver mounted on B&C ME 90 horn. within the range from the recommended crossover frequency to 0 k. impedance. defined as db greater than the 6 80 50 0 90 60 0 0 0 60 90 0 50 80 Applied RMS Voltage is set to.8 V for 8 ohms and V for 6 ohms. Average SPL from 000 to 8000. 5 Waveguide mounted on 90 x 0 bell horn. bcspeakers.com

HOR NS The range of B&C electro-acoustic systems is completed by a series of high frequency horns. The range includes constant directivity models that are known for their great consistency in angular coverage, and exponential models that optimize acoustical load and acoustic energy transfer. Standardized diameters give designers the freedom to choose the best driver/horn combination for each project. bcspeakers.com 5

ME0 HORN " throat entry Hyperbolic cosine flare 90 x 60 nominal coverage Excellent loading down to.5 k 6 horizontal angle 6 0 vertical angle Throat Diameter 5 mm ( in) 0 0-6 0 0 0-6 0 Nominal Coverage Horizontal 90 Vertical 60 Cutoff Frequency.5 k Material ABS Dimensions 0.5x0.5x90 mm (5.x5.x.5 in) 00 0 - -8 - -0-6 60 90 k k 0 k 00 0 - -8 - -0-6 60 90 0 HOR NS MOUNTING A SHIPPING INFORMATION Four 6mm(0.5 in) holes 90 on 76 mm ( in) diameter Baffle Cutout Dimensions 0x0 mm (x. in) ( unit) 0.5 kg (0. lb) (0 units) 6 Kg (. lb) (0 units) 50x50x90 mm (.x.8x5. in) Horn mounted on B&C DE500 compression driver. 0 50 5 0 8 k k 6 k HORIZONTAL ANGLE frequency VERTICAL ANGLE frequency 0 80 50 0 90 60 0 0 0 60 90 0 50 80 6 5 0 80 50 80 50 0 90 60 0 0 0 60 90 0 50 80 6 ME0 HORN " throat entry Excellent loading down to.5 k 90 x 60 nominal coverage Exponential flare 6 horizontal angle 6 0 vertical angle Throat Diameter 5 mm ( in) 0 0-6 0 0 0-6 0 Nominal Coverage Horizontal 90 Vertical 60 Cutoff Frequency.5 k Material Cast Dimensions 5x5x90 mm (5.7x5.7x.6 in) 00 0 - -8 - -0-6 60 90 k k 0 k 00 0 - -8 - -0-6 60 90 0 MOUNTING A SHIPPING INFORMATION Two 6mm(0.5 in) holes 80 on 76 mm ( in) diameter Baffle Cutout Dimensions ( unit) 8x mm (.6x. in) 0.5 kg ( lb) (0 units).0 Kg (6. lb) (0 units) 50x50x90 mm (.x.8x5. in) Horn mounted on B&C DE500 compression driver. 0 50 5 0 8 k k 6 k HORIZONTAL ANGLE frequency VERTICAL ANGLE frequency 0 80 50 0 90 60 0 0 0 60 90 0 50 80 6 5 0 80 50 80 50 0 90 60 0 0 0 60 90 0 50 80 6 bcspeakers.com 6

ME5 HORN " throat entry Exponential flare 90 x 0 nominal coverage Excellent loading down to k 6 0 horizontal angle 6 0 vertical angle Throat Diameter 5 mm ( in) 0 0-6 0 0 0-6 0 Nominal Coverage Horizontal 90 Vertical 0 Cutoff Frequency k Material Cast Dimensions 0x.5x mm (.5x5.6x.9 in) 00 0 - -8 - -0-6 60 90 k k 0 k 00 0 - -8 - -0-6 60 90 0 HOR NS 8 k MOUNTING A SHIPPING INFORMATION 0 80 50 k 6 k 0 80 50 Two 6.5 mm (0.5 in) holes 80 on 76 mm ( in) diameter Baffle Cutout Dimensions 60x0 mm (0.x. in) ( unit) 0.8 kg (.8 lb) (0 units).9 Kg (0.8 lb) (0 units) 50x50x85 mm (.x.8x7. in) HORIZONTAL ANGLE frequency VERTICAL ANGLE frequency 80 50 0 90 60 0 0 0 60 90 0 50 80 80 50 0 90 60 0 0 0 60 90 0 50 80 Horn mounted on B&C DE5 compression driver. 5 0 6 5 0 6 ME90 HORN." throat entry Constant directivity 80 x 60 nominal coverage Excellent loading down to 900 6 0 horizontal angle 6 0 vertical angle Throat Diameter 6 mm (. in) 0 0-6 0 0 0-6 0 Nominal Coverage Horizontal 80 Vertical 60 Cutoff Frequency 900 Material Cast 70x70.5x8 mm (0.6x0.6x5. in) 00 0 - -8 - -0-6 60 90 k k 0 00 0 - -8 - -0-6 60 90 0 k MOUNTING A SHIPPING INFORMATION 0 80 50 8 k k 6 k 0 80 50 Four 6.5 mm (0.5 in) holes 90 on 0 mm ( in) diameter Baffle Cutout Dimensions 5x5 mm (8.8x8.8 in) 0. kg (. lb).9 Kg (. lb) 90x90x70 mm (.x.x6.7 in) HORIZONTAL ANGLE frequency VERTICAL ANGLE frequency 80 50 0 90 60 0 0 0 60 90 0 50 80 80 50 0 90 60 0 0 0 60 90 0 50 80 5 0 6 5 0 6 Horn mounted on B&C DE900 compression driver. bcspeakers.com 7

HOR NS ME60 HORN " throat entry 60 x 0 nominal coverage Constant directivity Excellent loading down to 800 6 0 horizontal angle 6 0 vertical angle Throat Diameter 50 mm ( in) Nominal Coverage Horizontal 60 Vertical 0 Cutoff Frequency 800 Material Cast Dimensions 70x7x0 mm (0.6x9.x7.9 in) 00 0 0-6 - -8 - -0-6 0 60 90 00 0 0-6 - -8 - -0-6 0 60 90 k MOUNTING A SHIPPING INFORMATION Four 6.5 mm (0.5 in) holes 90 on 0 mm ( in) diameter Baffle Cutout Dimensions x07 mm (9.x8. in).6 kg (.5 lb). Kg (.8 lb) 90x60x60 mm (.x0.x0. in) 0 0 0 80 6 0-6 - 00 HORIZONTAL ANGLE 60 frequency 00 VERTICAL ANGLE 60 frequency -8 - -0-6 k 0 0 0 k 8 k 0 0 50 k 0 6 k 80 50 0 6 0-6 - -8 - -0-6 0 0 0 50 80 90 90 90 90 60 60 0 0 0 0 80 50 0 0 0 Horn mounted on B&C DE750 compression driver. 0 60 0 90 0 60 0 90 0 0 50 50 50 0 5 0 80 0 50 80 6 5 0 80 6 80 bcspeakers.com 8