00 r. Greaves Rd. Kansas City, MO 00 (1) 1- F (1) - I and I CURTIN TYPE YNMIC FIRE MPERS 1 1 / N OUR UL RTE FOR USE IN YNMIC N STTIC SYSTEMS PPLICTION I fire dampers can be installed vertically in walls or horizontally in floors with fire resistance ratings of less than hours. The I carries a 1 1 / hour UL fire damper label and is classified as a dynamic damper for use in VC systems that remain in operation during a fire. I fire dampers can be installed vertically in walls or horizontally in floors with fire resistance ratings of hours or more. The I carries a hour UL fire damper label and are classified as a dynamic damper for use in VC systems that remain in operation during a fire. YNMIC CLOSURE RTINGS 000 fpm (. m/s) vertical mount only, up to x ( x ). 000 fpm (. m/s) vertical and horizontal mount, up to x ( x ). 00 fpm (. m/s) vertical or horizontal mount on all sizes. in. w.g. (1kPa) maximum pressure on all sizes. STNR CONSTRUCTION FRME gage (1.0) galvanized, steel channel. LES gage (.) galvanized curtain type. CLOSURE SPRINGS 01 stainless steel constant force or spring clip type. FUSILE LINK 1 F ( C) is standard. F (0 C) and F (1 C) are available. MPER SIZES The sizes listed below are for Style dampers. Refer to pages and for sizes of other style dampers. Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) for dampers no larger than w or h ( or ). ampers larger than w or h ( or ) have a minimum size of w or h ( or ). MIMUM SIZE Single Section Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) Multiple Section Vertical Installation "w x "h ( x 1), "w x "h (1 x ) or 1"w x "h (0 x )** **0"w x "h ( x ) for I orizontal Installation "w x "h ( x 1) OPTIONS FM pprovals as Specification Tested Product. Switch Package to remotely indicate damper blade position. FST ngle for one side angle installations. G Style for grille applications. G, Grille ccess Type for out of the wall/floor and no angle grille applications. OW, Out of Wall Type for out of wall/floor installations. Sleeve of various lengths and gages to insure field compliance with UL installation requirements. ccess oor factory mounted in common sleeve to ensure compliance with UL installation requirements. NOTE: Models I and I meet the requirements for fire dampers established by: National Fire Protection ssociation NFP Standards 0, 0 and 1 ICC International uilding Codes CSFM California State Fire Marshal Fire amper Listing (#-:00 and #-:00) New York City (S Listing #-1-S and #--S) UL CLSSIFIE UL Listing R1 eight Width SEE COMPLETE MRKING ON PROUCT eight Width FM pprovals Specification Tested Product (Option) () STYLE FRME N LES IN IRSTREM I OR STYLE IN GGE FCTORY SLEEVE Taped and sealed on vertical sizes up to "w x "h ( x ) and horizontal sizes up to "w x "h ( x ). Spec I & I-0/Replaces I & I-0 LL STTE SPECIFICTIONS RE SUJECT TO CNGE WITOUT NOTICE OR OLIGTION. Ruskin 0
MPER STYLES N SIZES Style lades out of airstream for high free area applications Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) for dampers no larger than w or 1 h ( or ). ampers larger than w or 1 h ( or ) have a minimum size of w or h ( or ) MIMUM SIZE Single Section Vertical Installation "w x "h ( x 1) orizontal Installation "w x 1"h ( x ) Multiple Section Vertical Installation "w x "h ( x ), "w x "h (1 x 1) or 1"w x 1"h (0 x )** **0"w x 1"h ( x ) for I orizontal Installation "w x "h ( x ) = uct Width = uct eight = Overall amper eight L = Sleeve Length Taped and sealed on vertical sizes up to "w x "h ( x 1) and horizontal sizes up to "w x 1"h ( x ). I or STYLE IN FCTORY SLEEVE 1 1 /" () C Style Welded style for high pressure, high free area applications Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) for dampers no larger than w or 1 h ( or ). ampers larger than w or 1 h ( or ) have a minimum size of w or h ( or ). MIMUM SIZE Single Section Vertical Installation "w x "h ( x 1) orizontal Installation "w x 1"h ( x ) Multiple Section Vertical Installation "w x "h ( x ), "w x "h (1 x 1) or 1"w x 1"h (0 x )** **0"w x 1"h ( x ) for I orizontal Installation "w x "h ( x ) " amper must be ordered with minimum 1 gage (1.) x = uct Width = uct eight = Overall amper eight factory sleeve. C and WC Style Sealed (C) or welded (WC) square or rectangular transition for maximum free area applications Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) for dampers no larger than w or h ( or 0). ampers larger than w or h ( or 0) have a minimum size of w or h ( or 1). MIMUM SIZE Single Section Vertical Installation 1"w x 1 h ( x ) orizontal Installation "w x "h ( x 0) Multiple Section Vertical Installation 0"w x "h (1 x 1), "w x "h ( x ) or "w x "h ( x 0)** ** w x h ( x 0) for I orizontal Installation "w x "h ( x ) + ( + 1) = uct Width = uct eight = Overall amper eight L = Sleeve Length Taped and sealed on sizes up to 1 w x 1 h ( x ) for vertical installation and w x h ( x 0) for horizontal installation. + ( + 1) I OR STYLE C IN FCTORY SLEEVE 1 1 /" () for C 1 /" () for WC CR and WR Style Sealed (CR) or welded (WR) round transition for 0% free area applications Vertical Installation " diameter orizontal Installation " () diameter MIMUM SIZE Vertical Installation Single Section 1" () diameter Multiple Sections " (1) diameter orizontal Installation Single Section " diameter Multiple Sections " () diameter + ( + 1) Taped and sealed on sizes up to 1 () in diameter for vertical installation and in diameter for horizontal installation. + ( + 1) 1 1 /" () for CR 1 /" () for WR = iameter = Overall amper eight L = Sleeve Length ia. I OR STYLE CR IN FCTORY SLEEVE
MPER STYLES N SIZES CO and WO Style Sealed (CO) or welded (WO) oval transition for 0% free area applications Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) for dampers no larger than w or h ( or 0). ampers larger than w or h ( or 0) have a minimum size of w or h ( or 1). MIMUM SIZE Vertical Installation Single Section 1"w x 1 h ( x ) Multiple Sections 0"w x "h (1 x 1), "w x "h ( x ) or "w x "h ( x 0)** ** w x h ( x 0) for I orizontal Installation Single Section "w x "h ( x 0) Multiple Sections "w x "h ( x ) + ( + 1) Taped and sealed on sizes up to 1 w x 1 h ( x ) for vertical installation and w x h ( x 0) for horizontal installation. + " + (1) 1 1 /" () for CO 1 /" () for WO = uct Width = uct eight = Overall amper eight L = Sleeve Length I OR STYLE CO IN FCTORY SLEEVE LO, LR and R Style Non-sealed oval (LO) or round (LR, R) transitions for low pressure applications. LO and LR transitions offset for 0% free area applications. R transition centered for use when 0% free area not required. Vertical Installation LR, R Styles " diameter LO Style "w x "h ( x ) orizontal Installation LR, R Styles " () diameter LO Style "w x "h ( x ) MIMUM SIZE Vertical Installation LR, R Styles 1" ( ) diameter LO Style 1"w x 1"h ( x ) orizontal Installation LR, R Styles " diameter LO Style "w x "h ( x 0) STYLE LO STYLE R STYLE LR 1 1 /" () when damper is sleeved 1 /" () when damper is not sleeved = uct Width = uct eight = Overall amper eight = iameter L = Sleeve Length
SSEMLY N IMENSIONL INFORMTION ampers normally fabricated approximately 1/" () less than given duct dimensions. (width) and (height) dimensions shown describe maximum UL Classified sizes. Ruskin recommends the authority having jurisdiction, the engineer and the contractor agree on the installation design prior to installation. I and I multiple section dampers ordered without sleeves are shipped in individual sections, for field assembly. I and I multiple section dampers ordered with factory furnished sleeves are normally shipped in complete assemblies. If TF or other flanged breakaway connections are to be used, order dampers with factory furnished sleeves actual size. STYLE MPERS VERTICL INSTLLTION Important Note: ampers larger than " x " ( x ) are multiple section dampers consisting of equal sections no larger than " x " ( x ). x x " () " () " () " () x x x " (1) x " () x x 0 () " () 1" (0) " (1) () " () 1 1 1 1 1 1 0 1 () (0) (0) () (1) () () () () () () () (0) () () () () () (1) () () () () lade imensions / / 1/ 1 / 1/ / / / / / / / 1 / 1/ 1 / 1 / 1/ 1 / 1 / 1 / 1 / 1/ / / / / () () () () () (1) (1) (0) (0) () () () (0) (0) () () () () () () () () () () () () () () () ORIZONTL INSTLLTION Important Note: ampers larger than " x " ( x ) are multiple section dampers consisting of equal sections no larger than " x " ( x ). lade p p imensions ) " () " () 1" " () " (1) " () " () " (1) 1 1 1 1 1 1 () (0) (0) () (1) () () () () () () 1 1 / 1 1 / 1/ 1 / 1/ / / / / / / / () () () () () (1) (1) (1) (1) (0) (0) (0) () () (0) (0) Important Notes: 1. ampers larger than " x " ( x ) are multiple section dampers consisting of equal sections no larger than 1" x " ( x ).. ampers larger than "w or "h ( x ) have a minimum size of "w or "h ( x ).
N C STYLE MPERS VERTICL INSTLLTION " () " " () () " (1) 1" " 1 () 1 1 1 1 1 1 0 1 () () () (0) (0) () (1) () () () () () () () (0) () () () () () (1) / / / / / / / 1 / / / 1 / 1 / 1 / / 1 / / / / / / / / / 0 / 1 / / / / / () () (1) () () () () () (00) () (1) () () () (0) (0) () () (0) (0) () (1) (0) () () () (0) For dampers larger than () W / / 1 / / 1 / / () () (0) () () " () " () 1" (0) " (1) " " (1) (1) 1" () Important Note: ampers larger than " x " ( x 1) are multiple section dampers consisting of equal sections no larger than " x " ( x ) overall. To determine the overall height ( dimension) of double high and triple high damper assemblies: dd /" (0) to the dimension. For example, a " () double high assembly is /" () overall height. " (11) triple high assembly is /" (1) overall height. The bottom sections on double and triple high assemblies are Style dampers. 0 () 1 () ORIZONTL INSTLLTION " () 1" () 1 1 1 1 1 1 () () () (0) (0) () (1) () () () / / / / / / / 1 / / / 1 / 1 / 1 / 1 / / 1 / / / () () (1) () () () () () (00) () (1) () (0) () () (0) 1" Max " () " () " () " () Important Notes: 1. ampers larger than " x 1" ( x ) are multiple section dampers consisting of equal sections no larger than 1" x " ( x ) overall.. ampers larger than "w or 1"h ( x ) have a minimum size of "w or "h ( x ). To determine the overall height ( dimension) of double high damper assemblies: dd 1 /" () to dimension on dampers over 1" () through " () and 1 /" (0) on all other dampers. For example, a damper with a " () dimension has an overall dimension of 1 /" (1). 1" ()
C, CO, WC, WO, LO N LC STYLE MPERS VERTICL INSTLLTION 1" () 1" () 1" () Important Note: ampers larger than 1" x 1" ( x ) are multiple section dampers consisting of equal sections no larger than " x " ( x ) overall. To determine the overall height ( dimension) of double high and triple high damper assemblies: dd /" () to the dimension. For example, a " () double high assembly is /" (0) overall height. " () triple high assembly is /" (1) overall height. The bottom sections on double and triple high assemblies are Style dampers with blades in the air stream. + " ( + 1) 0" (1) + " + (1) " () + " + (1) " () () 1" () + " + (1) " () " " 1 1 1 1 1 1 0 1 () () () (0) (0) () (1) () () () () () () () (0) () () () () () / / / / / / / 1 / / / 1 / 1 / 1 / / 1 / / / / / / / / / 0 / 1 / / / / / () () (1) () () () () () (00) () (1) () () () (0) (0) () () (0) (0) () (1) (0) () () () (0) " (1) " () + " ( + 1) " () 1" () " Important Notes: 1. ampers larger than " x " ( x 0) are multiple section dampers consisting of equal sections no larger than 1" x " ( x ) overall.. ampers larger than "w or "h ( x 0) have a minimum size of "w or "h ( x 1). To determine the overall height ( dimension) of double high damper assemblies: dd 1 /" () to dimension on dampers over " through " () and 1/" (0) to the dimension on all other dampers. For example, a " () double high assembly is 1 /" () overall height. 0" () double high assembly is 1 /" (1) overall height. ORIZONTL INSTLLTION + " ( + 1) " () + " ( + 1) " () " " () 1 1 1 1 1 () () () (0) (0) () (1) () () / / / / / / / 1 / / / 1 / 1 / 1 / 1 / / 1 / / / () () (1) () () () () () (00) () (1) () (0) () () (0)
CR, WR N LR STYLE MPERS VERTICL INSTLLTION 1" () Important Note: ampers larger than 1" () diameter are multiple section dampers consisting of equal sections no larger than " x " ( x ) overall. To determine the overall height ( dimension) of double high damper assemblies: dd /" () to dimension on dampers. For example, a 0" (1) double high assembly is /" () overall height. The bottom sections on double high assemblies are Style dampers with blades in the air stream. + " ( + 1) 1" () " (1) 1 1 1 1 1 1 0 1 () () () (0) (0) () (1) () () () () () () () (0) () () () () () / / / / / / / 1 / / / 1 / 1 / 1 / / 1 / / / / / / / / / 0 / 1 / / / / / () () (1) () () () () () (00) () (1) () () () (0) (0) () () (0) (0) () (1) (0) () () () (0) ORIZONTL INSTLLTION " 0 Important Note: ampers larger than " diameter are multiple section dampers consisting of equal sections no larger than 1" x " ( x ) overall. To determine the overall height ( dimension) of double high damper assemblies: dd 1 /" () to dimension on dampers over " through " () and 1 /" (0) on all other sizes. For example, a " () double high assembly is 1 /" () overall height. " () 1 1 1 1 1 () () () (0) (0) () (1) () () / / / / / / / 1 / / / 1 / 1 / 1 / 1 / / 1 / / / () () (1) () () () () () (00) () (1) () (0) () () (0)
LOR SVER OPTIONS TF OR UCTMTE REKWY CONNECTIONS Meet UL breakaway connection requirements without changing connectors. Ruskin fire dampers can be installed using non-matched flange connections for the breakaway requirement. ny flange connection can mate to a different type or model on Ruskin fire dampers. FST MOUNTING NGLE FST mounting angles are used in lieu of conventional, eight piece mounting angles and are installed on only one side of the wall when used with Ruskin I fire dampers. The FST angle can be fastened directly to the metal stud underneath the fire rated gypsum wallboard. VOC Content (g/l) - 0 Manufacturing Locations (MR Credit.1) Mira Loma, C 1 Parsons, KS Lexington, KY 00 Fairmont, WV LEE 0 Information Recycled Content (MR Credit.1 &.).% Post Consumer.% Pre-Consumer Post Industrial pproximate amper ssembly Weight lbs. per sq. ft. without sleeves lbs. per sq. ft. with ga. sleeves SUGGESTE SPECIFICTION FOR I Furnish and install, at locations shown on the plans, dynamic fire dampers tested, constructed and labeled in accordance with the latest edition of UL Standard. ampers shall have a fire rating of 1 1 / hours and shall meet the requirements of the latest edition of NFP0. Each damper shall include a 1 F ( C) or F (0 C) fusible link (specifier select) and shall be labeled for use in dynamic systems. ampers labeled for use in static systems only are not permitted. The damper shall be rated for dynamic closure at 00 fpm (.1 m/s) and inches w.g. (1 kpa) static pressure and shall be rated to close with airflow in either direction. Each dynamic fire damper shall include a steel sleeve and mounting angles furnished by the damper manufacturer to ensure appropriate installation. Submittal information shall include the fire protection rating, maximum velocity/pressure ratings and the manufacturer's UL installation instructions. The dampers shall be installed in accordance with the manufacturer s UL installation instructions. ynamic fire dampers shall be curtain type Ruskin model I. SUGGESTE SPECIFICTION FOR I Furnish and install, at locations shown on the plans, dynamic fire dampers tested, constructed and labeled in accordance with the latest edition of UL Standard. ampers shall have a fire rating of hours and shall meet the requirements of the latest edition of NFP0. Each damper shall include a 1 F ( C) or F (0 C) fusible link (specifier select) and shall be labeled for use in dynamic systems. ampers labeled for use in static systems only are not permitted. The damper shall be rated for dynamic closure to a minimum 00 fpm (.1 m/s) and inches w.g. (1 kpa) static pressure and shall be rated to close with airflow in either direction. Each dynamic fire damper shall include a steel sleeve and mounting angles furnished by the damper manufacturer to ensure appropriate installation. Submittal information shall include the fire protection rating, maximum velocity/pressure ratings and the manufacturer's UL installation instructions. The dampers shall be installed in accordance with the manufacturer s UL installation instructions. ynamic fire dampers shall be curtain type Ruskin model I. 00 r. Greaves Rd. Kansas City, MO 00 (1) 1- F (1) - www.ruskin.com Printed on recycled paper using vegetable based inks