DV28 This light can be surface mounted in areas needing low level lighting for steps, walkways, doorways and for general lighting on larger boats. The bolted bezel is machined stainless steel 316 L and ensures a strong exterior for exposed areas. It is available with a frosted and clear lens depending on which light version you choose. This light uses the best quality materials and is designed for longevity and tested for water tightness to IP66. The DV28 is available in 12 or 24 volt with a twin MR11 lamp option, maximum wattage 20 watts per lamp and 12 or 24 volt LED. LED colors available are cool white, warm white, blue and red. DV28 technical specifications Application for: Steps, walkways, doorways Finish: Polished stainless steel 316 L Bezel: Bolted Glass lens: Clear or frosted Power supply: 12 volt d.c./a.c halogen - 3.2 amps 24 volt d.c. halogen - 1.6 amps 12 volt d.c. LED - 0.38 amps 24 volt d.c. LED - 0.19 amps Lamp: Two 20w halogen 12/24 volt 12 or 24 volt LED available in cool white, warm white, blue and red Dimensions: Bezel: 5.7 / 145mm x 3.54 / 90mm Depth: 3.4 / 86mm Cut-out: 4.4 / 112mm x 2.24 / 57mm IP rating: 66 All information is subject to change without prior notice, please confirm details prior to ordering. For further technical installation information, please visit www.seavision.com, T. 954 760 4447 Toll Free 1 866 772 0130 F. 954 525 3261 sales@seavision.com www.seavision.com
DV28 Light, 12VDC or 24 VDC Introduction: Congratulations on the purchase of your new deck light. Underwater Lights USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to enhance your boating experience. These lights can be installed in your vessel for aesthetics, security and safety. General Operating Information: The two commercial grade Halogen lamps used in this light will provide robust and reliable operation under normal operating conditions. Also, each lamp can independently swivel in the forward looking direction to achieve the desired illumination. General Safety Information: This light is intended for vessel exterior (rain or indirect water spray) lighting applications. Always disconnect and lock-out power before working on light. Technical Specifications: Lamps = Two 20 watt - Halogen - 3000 Kelvin color temperature - Approximately 4,000 hours life Note: Each lamp can swivel ±15 from centerline (or within a 30 included angle cone) in the forward looking direction Glass = Borosilicate glass - 3.2mm (0.125 ) thick - 101mm (4 ) wide x 46mm (1.8 ) high net aperture Dimensions = 145mm (5.7 ) wide x 90mm (3.54 ) high x 86mm (3.4 ) deep - 534 grams ( 1.2 lbs) Mounting = Fits through a 112mm (4.4 ) wide x 57mm (2.24 ) high oval hole Construction = Stainless steel - Marine aluminum alloy - White PTFE (Teflon) Power supply = 12VDC / AC - 3.2 Amps, 24VDC - 1.6 Amps - Minimum operating temperature -30 C (-22 F) Troubleshooting: Please contact our technical support staff in Florida at 1-954-760-4447, Monday to Friday from 8:00 am to 5:00 pm EST. Warranty: Underwater Lights USA, LLC warrants this light to be free from defects in workmanship and materials for a period of one year from the date of original purchase (except lamps). Further, misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as fire, flood and lightning, unauthorized repair or modifications will void said warranty. Should your light prove defective during the warranty period, promptly contact Underwater Lights USA, LLC for an RMA number and then return the light freight prepaid with the RMA number clearly marked on the outside of the shipping container. Fax: 1-954-525-3261 Internet: www.seavision.com Email: sales@seavision.com DOC:022706-3
DV28 Light, 12VDC or 24 VDC Installation: After selecting a flat surface, cut a 112mm (4.4 ) wide x 57mm (2.24 ) high oval hole through said surface at the desired location. Caution! Check that no electrical wiring, fuel lines, oil lines, water lines etc., pass near or through the intended hole location. Remove six Socket Flat Head Screws (13), Front Flange (2) and six supplied Phillips Flat Head Screws (11). Place Main Body (1) with Large Body O-Ring (9) through above oval hole and carefully secure using six Phillips Flat Head Screws (11). Note: Depending upon installation surface material, six small pilot holes may be required. Place Front Flange (2) onto Main Body (1) and secure using six Socket Flat Head Screws (13). Connect the first wire lead to a switched and fused power source then connect the second wire lead to good ground. Note: The light has no electrical polarity. Serviceable Parts: Lamp replacement is done by removing six Socket Flat Head Screws (13) and Front Flange (2), pulling the old Lamp (17) out of the Lamp Socket (16), carefully pushing a new Lamp (17) into the Lamp Socket (16), installing the Front Flange (2) onto the Main Body (1) and securing with six Socket Flat Head Screws (13). Caution! Ensure that the new lamp is clean and free of dust, dirt, grease, oil, water and finger prints. Additionally, Glass (3) and Front Flange (2) are a permanently bonded assembly. BALLOON PART DESCRIPTION 1 28001 MAIN BODY* 2 28006 FRONT FLANGE, STAINLESS STEEL, MIRROR FINISH* 3 28014 GLASS, CLEAR* 4 28019 SWIVEL CONE 5 28053 INTERNAL RETAINING RING 6 28022 28023 SWIVEL FRAME, STAINLESS STEEL, BRUSHED FINISH* SWIVEL FRAME, STAINLESS STEEL, NATURAL FINISH* 7 28030 BACK COVER 8 28031 SMALL BODY O-RING 9 28032 LARGE BODY O-RING 10 28033 M5 x 0.8 STAINLESS STEEL HEX NUT 11 28034 12 28035 13 28036 14 28037 No. 8 x 3/4 LG STAINLESS STEEL PHILLIPS FLAT HEAD SCREW M3 x 0.5 x 20 LG STAINLESS STEEL M5 x 0.8 x 8 LG STAINLESS STEEL SOCKET FLAT HEAD SCREW 15 28038 CABLE STRAIN RELIEF 16 28039 LAMP SOCKET 17 28040 28043 LAMP, 20 WATT, 12VDC* LAMP, 20 WATT, 24 VDC* 18 28044 M3 x 0.5 x 6 LG STAINLESS STEEL SOCKET HEAD CAP SCREW 19 28045 REFLECTOR, 30 BEAM ANGLE* *PLEASE CALL FOR OTHER LIGHT COMPONENT CONFIGURATIONS Fax: 1-954-525-3261 Internet: www.seavision.com Email: sales@seavision.com DOC:022706-3
DV28 Light, 12VDC or 24VDC LED Array Introduction: Congratulations on the purchase of your new deck light. Underwater Lights USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to enhance your boating experience. These lights can be installed in your vessel for aesthetics, security and safety. General Operating Information: The commercial grade Light Emitting Diode (LED) technology used in this light will provide robust and reliable operation under normal operating conditions. General Safety Information: This light is intended for vessel exterior (rain or indirect water spray) lighting applications. Always disconnect and lock-out power before working on light. Technical Specifications: Light source = Three cool white, warm white, blue or red LED arrays - 4.5 Watts total - Approximately 10,000 hours life Glass = Borosilicate glass - 3.2mm (0.125 ) thick - 101mm (4 ) wide x 46mm (1.8 ) high net aperture Dimensions = 145mm (5.7 ) wide x 90mm (3.54 ) high x 86mm (3.4 ) deep - 525 grams ( 1.1 lbs) Mounting = Fits through a 112mm (4.4 ) wide x 57mm (2.24 ) high oval hole Construction = Stainless steel - Marine aluminum alloy - White PTFE (Teflon) Power supply = 12VDC - 0.38 Amps, 24VDC - 0.19 Amps Troubleshooting: Please contact our technical support staff in Florida at 1-954-760-4447, Monday to Friday from 8:00 am to 5:00 pm EST. Warranty: Underwater Lights USA, LLC warrants this light to be free from defects in workmanship and materials for a period of one year from the date of original purchase. Further, misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as fire, flood and lightning, unauthorized repair or modifications will void said warranty. Should your light prove defective during the warranty period, promptly contact Underwater Lights USA, LLC for an RMA number and then return the light freight prepaid with the RMA number clearly marked on the outside of the shipping container. Fax: 1-954-525-3261 Email: sales@seavision.com DOC:022806-5
DV28 Light, 12VDC or 24VDC LED Array Installation: After selecting a flat surface, cut a 112mm (4.4 ) wide x 57mm (2.24 ) high oval hole through said surface at the desired location. Caution! Check that no electrical wiring, fuel lines, oil lines, water lines etc., pass near or through the intended hole location. Remove six Socket Flat Head Screws (11), Front Flange (2) and six supplied Phillips Flat Head Screws (9). Place Main Body (1) with Large Body O-Ring (7) through above oval hole and carefully secure using six Phillips Flat Head Screws (9). Note: Depending upon installation surface material, six small pilot holes may be required. Place Front Flange (2) onto Main Body (1) and secure using six Socket Flat Head Screws (11). Connect red wire lead to a switched and fused power source. Connect black wire lead to a good ground. Serviceable Parts: LED array assembly replacement is done by removing six Socket Flat Head Screws (11), Front Flange (2), two Socket Head Cap Screws (10), LED Array Mounting Plate (4), disconnecting wire leads and then reversing said procedure to assemble. Additionally, Glass (3) and Front Flange (2) are a permanently bonded assembly. BALLOON PART DESCRIPTION 1 28001 MAIN BODY* 2 28006 FRONT FLANGE, STAINLESS STEEL, MIRROR FINISH* 3 28014 GLASS, CLEAR* 4 28048 LED ARRAY MOUNTING PLATE 5 28030 BACK COVER 6 28031 SMALL BODY O-RING 7 28032 LARGE BODY O-RING 8 28033 M5 x 0.8 STAINLESS STEEL HEX NUT 9 28034 No. 8 x 3/4 LG STAINLESS STEEL PHILLIPS FLAT HEAD SCREW 10 28052 SOCKET HEAD CAP SCREW 11 28036 M5 x 0.8 x 8 LG STAINLESS STEEL SOCKET FLAT HEAD SCREW 12 28037 13 28038 CABLE STRAIN RELIEF 14 28061 28062 COOL WHITE LED ARRAY, 12VDC* COOL WHITE LED ARRAY, 24VDC* 15 28060 M3 x 0.5 x 5 LG STAINLESS STEEL *PLEASE CALL FOR OTHER LIGHT COMPONENT CONFIGURATIONS Fax: 1-954-525-3261 Email: sales@seavision.com DOC:022806-5