SETION 1 FLUSH INSET INSTLLTION SETION 2 STNR INSTLLTION 1/4" FRME PNELS 3/4" OVERLY PNELS
OVERLL IMENSIONS FLUSH INSET INSTLLTION 38" (96.5) 25 7/8" (65.7) 20 5/8" (52.4) 10 5/16" (26.2) *8 (212.1) *73 1/4" (186.1) * 8 (212.1) 69 13/16" (177.3) SPEIFITIONS Overall Width 38" (96.5 cm) Overall Height 8 (212.1 cm) Overall epth 25 7/8" (65.7 cm) learance utout Width utout Height utout epth Plumbing Requirements Shipping Weight 38 3/4" (98.4 cm) 39" (99.1 cm) 84 1/2" (214.6 cm) 26 3/16" (66.5 cm) 1/4" O copper tubing or GE Smartonnect kit 570 lb (258.5 kg) *3 3/8" (8.6) FRONT VIEW * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84". ** llow 17" (43.2) min clearance for 115 door swing 35" (89.0) ase width *3" (7.6) SIE VIEW imensions include 3/4" custom cabinet panel TTENTION ELETRIIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n inidividual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. TOP VIEW 38 3/4" (98.4) ** llow 4" (10.2) min clearance to a wall for 90 door swing ** These freezers are equipped with a 2-position door stop. The factory-set 115 door swing can be adjusted to 90 if clearances to adjacent cabinets or walls is restricted. llow a 15" minimum clearance to wall for pan removal. If the 90 door stop position is used, pan access is maintained, but pan removal is restricted. imensions in parentheses are in centimeters unless otherwise noted. ctual product dimensions may vary due to manufacturing tolerances.
FLUSH INSET INSTLLTION 3/4" PNELS 84 1/2" (214.6) 26 3/16" (66.5) Flush inset depth 20 15/16" (53.2) epth to cleat Finished cleats 5 1/4" (13.3) 3/4" (1.9) Width of side cleats 84 1/2" (214.6) 3/4" TOP VIEW Finished cleats ase Trim ase 39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats ELE. 9" (22.9) 5 1/2" (14.0) 26 3/16" (66.5) 1/2" (1.3) 75" (190.5 ) From floor to bottom of electrical area FLUSH INSET INSTLLTION Mounting the junction box in this location will also allow for front accessability through access panel. Water supply area. WRNING: The freezer is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. W SIE VIEW NTI-TIP RKET 81 1/2" (207.0) SIE VIEW INSTLLE WITH NTI-TIP RKET Use two additional hole locations at end of brackets 7" (17.8) WTER (9.0) FRONT VIEW L racket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs Wall Studs 7" (17.8) FRONT VIEW OF UTOUT WITH NTI-TIP RKET The information below applies to all installation constructions: wall bracket, bolts and toggles will be supplied with the unit. The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. In installation opening, measure 81 ½ from floor and draw a horizontal line. Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32.5 of installation opening to ensure 2 wall studs are penetrated. The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied L bolts. See Installation Instructions for detailed instructions.
FLUSH INSET 3/4" PNEL IMENSIONS SINGLE INSTLLTION Grille PNEL SSEMLY ROSS SETION PNEL IMENSIONS 38" 9 5/8" 69 13/16" 1/4" Router ut epth for Hinge learance 3/4" Flush Inset PNEL SSEMLY ROSS SETION HINGE LERNES ROUTER 1/4" EEP FLUSH INSET 3/4" PNEL IMENSIONS UL INSTLLTION X Y Z HINGE LERNE X Y Z 1 1/4" 1" 1/2" FLUSH INSET INSTLLTION Trimmed freezers are designed to be customized with decorative panels. Fieldinstalled custom door and grille panels are required. djustment brackets allow 1/8 fine adjustment of panel position in 3 dimensions. Use templates provided to locate mounting brackets on the door and grille panels. Maximum total panel weight: Fresh food door panels 67 lbs. Grille panel 11 lbs Handles handles not included. ustom handle supplied by your cabinet maker may be used. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4 panels. Kit includes one handle 30 1/2 long. ZKHSS2: European tubular stainless steel handle designed to fit 3/4 panels. Kit includes one handle 64 1/4 long. Order #ZUGF2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. NOTE: For side-by-side installation of a leftand-right-hand door swing product only, see on following page. Grille PNEL IMENSIONS 74 1/8" 9 5/8" 69 13/16" 36 15/16" HINGE LERNE X Y Z 1 1/4" 1" 1/2" HINGE LERNES ROUTER 1/4" EEP Z Y X PNEL SSEMLY ROSS SETION 1/4" Router ut epth for Hinge learance 3/4" Flush Inset PNEL SSEMLY ROSS SETION
UL INSTLLTIONS FLUSH INSET INSTLLTION 3 7/8" (9.8) 75 1/8" (190.8) Finished Width 25 3/4" (65.4) 26 3/16" (66.5) Min. utout epth 84 1/2" (214.6) Finished Opening ELE. 5 1/2" ELE. 5 1/2" 7" (17.8) 9" (22.9) (13.9) WTER (9.0) 5 3/4" (14.6) 9" (22.9) 5 3/4" (14.6) FRONT VIEW (13.9) WTER (9.0) 7" (17.8) 75 1/2" (191.8 ) From floor to bottom of electrical area W SIE VIEW separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product. In a side-by-side installation of a left-andright-hand door swing product, 1 1/2 clearance between the units is required. Order ZUGF2 custom panel unified grille kit for this installation. In a side-by-side installation with same door swing, allow 4 clearance between the products to prevent the door swing interference. llow 15 minimum to a wall to achieve full interior drawer extension and pan removal. dditional clearances are required when using custom panels and handles. NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel kits will not fit this installation. In a side-by-side installation with right and left door hinges together, allow 5 minimum clearance between the two products to prevent one door from striking the other. dditional clearances required when using custom panels and handles. NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel kits will not fit this installation. UL PROUT LERNES 25" (63.5) min To wall 1 1/2" (3.8) 25" (63.5) min To wall 4" min (10.2) 15" (38.1) min To wall 130 swing 130 swing 5" (12.7) min
OVERLL IMENSIONS STNR INSTLLTION 25 1/8" (63.8) 36" (91.5) 23 7/8" (60.7) 1 7/8" (4.8) *84" (213.4) *8 (212.1) 69 5/8" (176.8) *73 1/4" (186.1) SPEIFITIONS Overall Width 36" (91.4 cm) Overall Height Overall epth learance utout Width 84" (213.4 cm) 25 3/8" (64.45 cm) 36 3/4" (93.4 cm) 35 1/2" (90.2 cm) utout Height 8-84 1/2" (212.1-214.6 cm) utout epth 24" (61 cm) *3" (7.6) FRONT VIEW * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. 35" (89.0) ase width *3 1/4" (8.3) SIE VIEW Plumbing Requirements Shipping Weight 1/4" O copper tubing or GE Smartonnect kit 569 lb ** llow 25" (63.5) min clearance for 130 door swing TTENTION ELETRIIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n inidividual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. TOP VIEW 36 3/4" (93.4) ** llow 4" (10.2) min clearance to a wall for 90 door swing **These units are equipped with a 2-position door stop. The factory set 130 door swing can be adjusted to 90 if clearance to adjacent cabinets or walls is restricted. llow 15" minimum clearance to wall for pan removal. If the 90 door stop position is used, pan access is maintained but pan removal is restricted. imensions in parentheses are in centimeters unless otherwise noted. ctual product dimension may vary due to manufacturing tolerances.
STNR INSTLLTION 2 5/16" (5.9) *8 min *84 1/2" max (212.1-214.6) *Trim will overlap additional 7/16" NTI-TIP RKET 35 1/2" (90.2) ELE. 5 1/2" (14.0) 5" (12.7) 9" (22.9) WTER (9.0) SIE VIEW INSTLLE WITH NTI-TIP RKET 81 1/2" (207.0) 5" (12.7) 75 1/2" (191.8 ) From floor to bottom of electrical area Use two additional hole locations at end of brackets 3 1/8" (7.9) 24" (61.0 ) 7/16" (1.1) Trim overlap 1 1/2" (3.8) L racket mounted into vertical wall studs Ensure holes selected are centered on the studs Wall Studs W FRONT VIEW OF UTOUT WITH NTI-TIP RKET STNR INSTLLTION Mounting the junction box in this location will also allow for front accessability through access panel. Water supply area. WRNING: The freezer is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. The information below applies to all installation constructions: wall bracket, bolts and toggles will be supplied with the unit. The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. In installation opening, measure 81 ½ from floor and draw a horizontal line. Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32.5 of installation opening to ensure 2 wall studs are penetrated. The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied L bolts. See Installation Instructions for detailed instructions.
USTOM SIE PNELS F 1 7/8" (4.8) 24" (61.0) 3/16" (.5) *84 *84" (213.4) *epending on installation height STNR INSTLLTION F Side panels must be used whenever the sides of the freezer will be exposed. The 1/4 side panels will slip into the side case trim. Secure the panels to the freezer with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer. *3" - 4" (7.6-10.2) *epending on installation height 2 9/16" (6.5)
1/4" FRME PNEL IMENSIONS SINGLE INSTLLTION STNR INSTLLTION PNEL SSEMLY ROSS SETION Grille Trim 1/4" Framed Supplied Handles Trimmed freezers are designed to be customized with decorative panels. Fieldinstalled custom door and grille panels are required. 1/4 Framed s: Order trim kit #ZKT36SLHH for 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: panel 67 lbs. Grille panel 11 lbs PNEL IMENSIONS 1/4" Framed 33 7/8" 8 7/8" 69 5/16" 3/4" OVERLY PNEL IMENSIONS SINGLE INSTLLTION Grille PNEL SSEMLY ROSS SETION Trim 1/4" acker.10" Spacer PNEL IMENSIONS 1/4" acker 33 7/8" 8 7/8" 69 5/16".10" Spacer 32 1/2" 7 5/8" 67 15/16" 3/4" Overlay 34 1/8" 9" 69 9/16".25" +.10" +.75" = 1.10" Total Thickness 3/4" Overlay Supplied Handles 3/4 Overlay s: Order trim kit #ZKT36SLHH for 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. spacer panel 0.10" thick must be placed between the overlay and backer panels. enter each panel over the other. ssemble the panels with glue and screws. Screws must be countersunk into the backer panel. NOTE: Left-to-right offset is not always equal to top-to-bottom offset. Maximum total panel weight: panel 67 lbs. Grille panel 11 lbs Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. ustom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional Tubular Stainless Steel Handle designed to fit 3/4" overlay panels. Kits include one handle - 30 1/2" long. ZKHSS2: European tubular stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle - 64 1/4" long.
STNR 1/4" FRME PNEL IMENSIONS UL INSTLLTION Grille PNEL IMENSIONS 1/4" Framed 69 7/8" 8 7/8" 69 5/16" 33 7/8" STNR INSTLLTION Trimmed freezers are designed to be customized with decorative panels. Fieldinstalled custom door and grille panels are required. 1/4 Framed s: Order trim kit #ZKT36SLHH for 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: panel 67 lbs. Grille panel 25 lbs Order ZUGF2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. PNEL SSEMLY ROSS SETION Trim 1/4" Framed Supplied Handles STNR 3/4" OVERLY PNEL IMENSIONS UL INSTLLTION PNEL SSEMLY ROSS SETION Grille Trim 1/4" acker.10" Spacer 3/4" Overlay Supplied Handles PNEL IMENSIONS 1/4" acker.10" Spacer 3/4" Overlay 69 7/8" 68 1/2" 70 1/8" 8 7/8" 7 5/8" 9" 69 5/16" 67 15/16" 69 9/16" 33 7/8" 32 1/2" 34 1/8".25" +.10" +.75" = 1.10" Total Thickness 3/4 Overlay s: Order trim kit #ZKT36SLHH for 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. spacer panel 0.10" thick must be placed between the overlay and backer panels. enter each panel over the other. ssemble the panels with glue and screws. Screws must be countersunk into the backer panel. NOTE: Left-to-right offset is not always equal to top-to-bottom offset. Maximum total panel weight: panel 67 lbs. Grille panel 25 lbs Order ZUGF2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. ustom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional Tubular Stainless Steel Handle designed to fit 3/4" overlay panels. Kits include one handle - 30 1/2" long. ZKHSS2: European tubular stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle - 64 1/4" long.
UL INSTLLTIONS STNR INSTLLTION 2 5/16" (5.9) 71 1/2" (181.6) Finished Width 24 3/16" (61.4) ELE. 5 1/2" ELE. 5 1/2" (13.9) (13.9) 24" (61.0) Min. utout epth separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product. 9" (22.9) 9" (22.9) dditional cutout width may be required when side panels are used. 8 min 84 1/2" max (212.1-214.6) Finished Opening 5" (12.7) WTER (9.0) 5" 5" (12.7) (12.7) WTER (9.0) 5" (12.7) 75 1/2" (191.8 ) From floor to bottom of electrical area W In a side-by-side installation of a leftand-right-hand door swing product, 1 clearance between the units is required. Order ZUG2: ustom panel unified grille kit for one continuous grille panel. In a side-by-side installation with same door swing, allow 2 minimum clearance between the products to prevent the door swing interference. llow 15 minimum to a wall to achieve full drawer extension and pan removal. dditional clearances are required when using custom panels and handles. NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel kits will not fit this installation. FRONT VIEW SIE VIEW In a side-by-side installation with right and left door hinges together, allow 5 minimum clearance between the two products to prevent one door from striking the other. dditional clearances required when using custom panels and handles. UL PROUT LERNES NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel kits will not fit this installation. 25" (63.5) min To wall 1" (2.5) 25" (63.5) min To wall 2" min (5.1) 15" (38.1) min To wall 130 swing 130 swing 5" (12.7) min
FETURES N ENEFITS ustom Model - an be personalized with cabinet-matching panels and handles Enhanced Temperature Management System - With precise electronic controls and thermistors, maintains ideal storage conditions for frozen foods oncealed Ice rawer - Provides quick and easy access to filtered ice GE Water Filtration System - Provides clean, fresh-tasting water to the freezer's icemaker ENERGY STR Qualification - s an ENERGY STR partner, GE has determined that Monogram all-freezers meet the ENERGY STR guidelines for energy efficiency djustable, Wire Shelves, Gallon-Szie ins and Pullout askets - llow customizable storage for foods and containers of varying sizes oncealed Halogen Lighting System - Illuminates contents without compromising space R